xin/rt-thread-am
1
0
Fork 0
Code Issues Pull requests Projects Releases Packages Wiki Activity Actions

import RT-Thread@9217865c without bsp, libcpu and components/net

Browse source
This commit is contained in:
Zihao Yu 2023-05-20 16:23:33 +08:00
commit e2376a3709
1414 changed files with 390370 additions and 0 deletions
Download patch file Download diff file Expand all files Collapse all files

49
documentation/README.md Normal file
View file

@ -0,0 +1,49 @@
# Manual Catalogue
- [RT-Thread Introduction](introduction/introduction.md)
- [Start Guide: Simulate STM32F103 on KEIL simulator](quick-start/quick-start.md)
**Kernel**
- [Kernel Basics](basic/basic.md)
- [Thread Management](thread/thread.md)
- [Clock&Timer Management](timer/timer.md)
- [Inter-thread Synchronization](thread-sync/thread-sync.md)
- [Inter-thread Communication](thread-comm/thread-comm.md)
- [Memory Management](memory/memory.md)
- [Interrupt Management](interrupt/interrupt.md)
- [Kernel Porting](kernel-porting/kernel-porting.md)
**Tool**
- [User Manual of Env](env/env.md)
- [SCons](scons/scons.md)
**Device**
- [I/O Device Framework](device/device.md)
- [PIN Device](device/pin/pin.md)
- [UART Device](device/uart/uart.md)
- [ADC Device](device/adc/adc.md)
- [I2C Bus Device](device/i2c/i2c.md)
- [SPI Device](device/spi/spi.md)
- [PWM Device](device/pwm/pwm.md)
- [RTC Device](device/rtc/rtc.md)
- [HWTIMER Device](device/hwtimer/hwtimer.md)
- [WATCHDOG Device](device/watchdog/watchdog.md)
- [WLAN Device](device/wlan/wlan.md)
- [Sensor Device](device/sensor/sensor.md)
**Components**
- [FinSH Console](finsh/finsh.md)
- [Virtual File System](filesystem/README.md)
- [utest Framework](utest/utest.md)
- [Dynamic Module: dlmodule](dlmodule/README.md)
- [Socket Abstraction Layer: SAL](sal/sal.md)
- [AT Commands](at/at.md)
- [POSIX Interface](posix/README.md)
- [Ulog Log](ulog/ulog.md)
- [Power Management: PM](pm/pm.md)
- [Network Framework](network/network.md)

897
documentation/at/at.md Normal file
View file

@ -0,0 +1,897 @@
# AT Commands #
## Introduction to AT Commands
The AT command set was originally a control protocol invented by Dennis Hayes, initially used to control dial-up modems. Later, with the upgrade of network bandwidth, low-speed dial-up modems with very low speed essentially exited the general market, but the AT command set was retained. However, the AT command set lived on when major mobile phone manufacturers jointly developed a set of commands to control the GSM modules of mobile phones. The AT command set evolved on this basis and added the GSM 07.05 standard and the later GSM 07.07 standard to achieve more robust standardization.
After seeing use in GPRS control, 3G modules and similar devices, AT commands gradually become the de facto standard in product development. Nowadays, AT commands are also widely used in embedded development. AT commands are the protocol interfaces of the main chip and communication module. The hardware interface is usually the serial port, so the main control device can complete various operations through simple commands and hardware design.
**AT commands are a way of facilitating device connections and data communication between an AT Server and an AT Client.** The basic structure is shown below:
![AT Command Set](figures/at_framework.jpg)
1. The AT command consists of three parts: prefix, body, and terminator. The prefix consists of the character AT; the body consists of commands, parameters, and possibly used data; the terminator typically is `<CR><LF>` (`"\r\n"`).
2. The implementation of AT functionality requires the AT Server and the AT Client to work together.
3. An AT Server mainly receives commands sent by the AT Client, interprets the received commands and parameter formats, and delivers corresponding response data or actively sends data.
4. An AT Client is mainly used to send commands, wait for the AT Server to respond, and parse the AT Server response data or the actively sent data to obtain related information.
5. A variety of data communication methods (UART, SPI, etc.) are supported between an AT Server and an AT Client. Currently, the most commonly used communications protocol is UART.
6. The data that the AT Server sends to the AT Client is divided into two types: response data and URC data.
- Response Data: The AT Server response status and information received by the AT Client after sending the command.
- URC Data: Data that the AT Server actively sends to the AT Client generally appears only in some special cases, such as when a WiFi connection is disconnected, while it's receiving TCP data, etc. These situations often require special user handling.
With the popularization of AT commands, more and more embedded products use AT commands. The AT commands are used as the protocol interfaces of the main chip and the communication module. The hardware interface is generally a serial port, so that the master device can performs a variety of operations using simple commands and hardware design.
Although the AT command set has standardization to a certain degree, the AT commands supported by different chips are not completely unified, which directly increases the complexity to use. There is no uniform way to handle the sending and receiving of AT commands and the parsing of data.
In order to facilitate the user to use AT commands which can be easily adapted to different AT modules, RT-Thread provides AT components for AT Device connectivity and data communication. The implementation of the AT components consists of both a client and a server.
## Introduction to AT Components
The AT component is based on the implementation of the `AT Server` and `AT Client` of the RT-Thread system. The component completes the AT command transmission, command format and parameter parsing, command response, response data reception, response data parsing, URC data processing, etc..
**Command data interaction process.**
Through the AT component, the device can use the serial port to connect to other devices to send and receive parsed data. It can be used as an AT Server to allow other devices or even the computer to connect to complete the response of sending data. It can also start the CLI mode in the local shell to enable the device to support AT Server and AT Client at the same time. The usage of both modes simultaneously is mostly used for device development and debugging.
**AT component resource usage:**
- AT Client: 4.6K ROM and 2.0K RAM；
- AT Server: 4.0K ROM and 2.5K RAM；
- AT CLI: 1.5K ROM and almost no RAM is used.
Overall, the AT component resources are extremely small, making them ideal for use in embedded devices with limited resources. The AT component code is primarily located in `rt-thread/components/net/at/`. What follows are the main function of both AT Servers and AT Clients.
**Main Functions of AT Server:**
- Basic commands: A variety of common basic commands are implemented (ATE, ATZ, etc.);
- Command compatibility: Commands are case-insensitive, which increases command compatibility;
- Command detection: Commands support custom parameter expressions and implement self-detection of received command parameters;
- Command registration: User-defined commands can be easily added, in a way, similar to how the `finsh/msh` command is added;
- Debug mode: An AT Server CLI command line interaction mode is provided, which is mainly used for device debugging.
**Main Functions of AT Client:**
- URC data processing: The complete URC data processing method;
- Data analysis: Supports the analysis of custom response data, and facilitates the acquisition of relevant information in the response data;
- Debug mode: Provides AT Client CLI command line interaction mode, mainly used for device debugging;
- AT Socket: An extension of AT Client function, it uses the AT command set to send and receive as the basis. This is implemented through the standard BSD Socket API, which completes the data sending and receiving function, and enables users to implement complete device networking and data communication through AT commands.
- Multi-client support: The AT component supports multiple clients running simultaneously.
## AT Server ##
### AT Server Configuration ###
When we use the AT Server feature in the AT component, we need to define the following configuration in rtconfig.h:
| **Macro Definition** | **Description** |
| ---- | ---- |
|RT_USING_AT| Enable AT component |
|AT_USING_SERVER |Enable AT Server function|
|AT_SERVER_DEVICE |Define the serial communication device name used by AT Server on the device to ensure that it is not used and the device name is unique, such as `uart3` device.|
|AT_SERVER_RECV_BUFF_LEN|The maximum length of data received by the AT Server device|
|AT_CMD_END_MARK_CRLF|Determine the line terminator of the received command |
|AT_USING_CLI | Enable server-command-line interaction mode |
|AT_DEBUG|Enable AT component DEBUG mode to display more debug log information |
|AT_PRINT_RAW_CMD | Enable real-time display AT command communication data mode for easy debugging |
For different AT devices, there are several formats of the line terminator for the sending commands: `"\r\n"`、`"\r"`、`"\n"` - the user needs to select the corresponding line terminator in accordance to the device type connected to the AT Server and then determine the end of transmission command, defined as follows:
| **Macro Definition** | **Terminator** |
| ---- | ---- |
| AT_CMD_END_MARK_CRLF | `"\r\n"` |
| AT_CMD_END_MARK_CR | `"\r"` |
| AT_CMD_END_MARK_LF | `"\n"` |
The above configuration options can be added by Env tool. The specific path in Env is as follows:
```c
RT-Thread Components --->
Network --->
AT commands --->
[*] Enable AT commands
[*] Enable debug log output
[*] Enable AT commands server
(uart3) Server device name
(256) The maximum length of server data accepted
The commands new line sign (\r\n) --->
[ ] Enable AT commands client
[*] Enable command-line interface for AT commands
[ ] Enable print RAW format AT command communication data
```
After the add configuration is complete, you can use the command line to rebuild the project, or use `scons` to compile.
### AT Server Initialization ###
After enabling the AT Server in Env, you need to initialize it at startup to enable the AT Server function. If the component has been initialized automatically, no additional initialization is required. Otherwise, you need to call the following function in the initialization task:
```c
int at_server_init(void);
```
The AT Server initialization function, which belongs to the application layer function, needs to be called before using the AT Server function or using the AT Server CLI function. `at_server_init()` function completes initialization of resources stored by AT commands, such as data segment initialization, AT Server device initialization, and semaphore usage by the AT Server. It also creates an at_server thread for parsing the received data in the AT Server.
After the AT Server is successfully initialized, the device can be used as an AT Server to connect to an AT Client's serial device for data communication, or use a serial-to-USB conversion tool to connect to a PC, so that the PC-side serial debugging assistant can communicate with the AT Client.
### Add custom AT commands ###
At present, the format of the AT command set used by AT devices of different manufacturers does not have a completely uniform standard, so the AT Server in the AT component only supports some basic general AT commands, such as ATE, AT+RST, etc. These commands can only be used to meet the basic operation of the device. If users want to use more functions, they need to implement custom AT Server commands for different AT devices. The AT component provides an AT command addition method similar to the FinSH/msh command addition method, which is convenient for users to implement the required commands.
The basic commands currently supported by AT Server are as follows:
- AT: AT test command;
- ATZ: The device is restored to factory settings;
- AT+RST: Reboot device;
- ATE: ATE1 turns on echo, ATE0 turns off echo;
- AT&L: List all commands;
- AT+UART: Set the serial port information.
AT commands can implement different functions depending on the format of the incoming parameters. For each AT command, there are up to four functions, as described below:
- Test Function: `AT+<x>=?`, used to query the command's parameter, format and value range;
- Query Function: `AT+<x>?`, used to return the current value of the command parameter;
- Setting Function: `AT+<x>=...`, used for user-defined parameter values;
- Execution Function: `AT+<x>`, used to perform related operations.
The four functions of each command do not need to be fully implemented. When you add an AT Server command, you can implement one or several of the above functions according to your needs. Unimplemented functions can be represented by `NULL`. Then the custom function can be added to the list of basic commands. The addition method is similar to the way the `finsh/msh` commands are added. The function for adding commands is as follows:
```c
AT_CMD_EXPORT(_name_, _args_expr_, _test_, _query_, _setup_, _exec_);
```
|**Parameter** |**Description** |
| ---------- | ------------------------------- |
| `_name_ ` | AT command name |
| `_args_expr_` | AT command parameter expression; (NULL means no parameter, `<>` means mandatory parameter and `[]` means optional parameter） |
| `_test_` | AT test function name; (NULL means no parameter) |
| `_query_` | AT query function name; (ibid.) |
| `_setup_` | AT setup function name; (ibid.) |
| `_exec_` | AT performs the function name; (ibid.) |
The AT command registration example is as follows. The `AT+TEST` command has two parameters. The first parameter is a mandatory parameter, and the second parameter is an optional parameter. The command implements the query function and the execution function:
```c
static at_result_t at_test_exec(void)
{
at_server_printfln("AT test commands execute!");
return 0;
}
static at_result_t at_test_query(void)
{
at_server_printfln("AT+TEST=1,2");
return 0;
}
AT_CMD_EXPORT("AT+TEST", =<value1>[,<value2>], NULL, at_test_query, NULL, at_test_exec);
```
### AT Server APIs
#### Send Data to the Client (no newline)
```c
void at_server_printf(const char *format, ...);
```
This function is used by the AT Server to send fixed-format data to the corresponding AT Client serial device through the serial device. The data ends without a line break. Used to customize the function functions of AT commands in AT Server.
| **Parameter** | **D**escription |
|------|-------------------------|
| format | Customize the expression of the input data |
| ... | Input data list, variable parameters |
#### Send Data to the Client (newline)
```c
void at_server_printfln(const char *format, ...);
```
This function is used by the AT Server to send fixed-format data to the corresponding AT Client serial device through the serial device, with a newline at the end of the data. Used to customize the function functions of AT commands in AT Server.
| **Parameter** | **Description** |
|------|-------------------------|
| format | Customize the expression of the input data |
| ... | Input data list, variable parameters |
#### Send Command Execution Results to the Client
```c
void at_server_print_result(at_result_t result);
```
This function is used by the AT Server to send command execution results to the corresponding AT Client serial device through the serial device. The AT component provides a variety of fixed command execution result types. When you customize a command, you can use the function to return the result directly;
| **Parameter** | **Description** |
|------|-----------------|
| result | Command execution result type |
The command execution result type in the AT component is given in the enumerated type, as shown in the following table:
| Types of Command Execution Result | Description |
|------------------------|------------------|
| AT_RESULT_OK | Command Execution Succeeded |
| AT_RESULT_FAILE | Command Execution Failed |
| AT_RESULT_NULL | Command No Result |
| AT_RESULT_CMD_ERR | Command Input Error |
| AT_RESULT_CHECK_FAILE | Parameter Expression Matching Error |
| AT_RESULT_PARSE_FAILE | Parameter Parsing Error |
See the following code to learn how to use the `at_server_print_result` function:
```c
static at_result_t at_test_setup(const char *args)
{
if(!args)
{
/* If the parameter error after incoming orders, returns expression match error results */
at_server_print_result(AT_RESULT_CHECK_FAILE);
}
/* Return to successful execution under normal conditions */
at_server_print_result(AT_RESULT_OK);
return 0;
}
static at_result_t at_test_exec(void)
{
// execute some functions of the AT command.
/* This command does not need to return results */
at_server_print_result(AT_RESULT_NULL);
return 0;
}
AT_CMD_EXPORT("AT+TEST", =<value1>,<value2>, NULL, NULL, at_test_setup, at_test_exec);
```
#### Parsing Input Command Parameters
```c
int at_req_parse_args(const char *req_args, const char *req_expr, ...);
```
Among the four functions of an AT command, only the setting function has an input parameter, and the input parameter is to remove the rest of the AT command. For example, for a given command input `"AT+TEST=1,2,3,4"`, set the input parameter of the function to the parameter string `"=1,2,3,4"`.
The command parsing function is mainly used in the AT function setting function, which is used to parse the incoming string parameter and obtain corresponding multiple input parameters for performing the following operations. The standard `sscanf` parsing grammar used in parsing grammar here will also be described in detail later in the AT Client parameter parsing function.
| **Parameter** | **Description** |
|---------|-----------------------------------------------|
| req_args | The incoming parameter string of the request command |
| req_expr | Custom parameter parsing expression for parsing the above incoming parameter data |
| ... | Output parsing parameter list, which is a variable parameter |
| **Return** | -- |
| >0 | Successful, returns the number of variable parameters matching the parameter expression |
| =0 | Failed, no parameters matching the parameter expression |
| -1 | Failed, parameter parsing error |
See the following code to learn how to use the at_server_print_result function:
```c
static at_result_t at_test_setup(const char *args)
{
int value1,value2;
/* The input standard format of args should be "=1, 2", "=%d, %d" is a custom parameter parsing expression, and the result is parsed and stored in the value1 and value2 variables. */
if (at_req_parse_args(args, "=%d,%d", &value1, &value2) > 0)
{
/* Data analysis succeeds, echoing data to AT Server serial device */
at_server_printfln("value1 : %d, value2 : %d", value1, value2);
/* The data is parsed successfully. The number of parsing parameters is greater than zero. The execution is successful. */
at_server_print_result(AT_RESULT_OK);
}
else
{
/* Data parsing failed, the number of parsing parameters is not greater than zero, and the parsing failure result type is returned. */
at_server_print_result(AT_RESULT_PARSE_FAILE);
}
return 0;
}
/* Add the "AT+TEST" command to the AT command list. The command parameters are formatted as two mandatory parameters <value1> and <value2>. */
AT_CMD_EXPORT("AT+TEST", =<value1>,<value2>, NULL, NULL, at_test_setup, NULL);
```
#### Porting-related interfaces
The AT Server supports a variety of basic commands (ATE, ATZ, etc.) by default. The function implementation of some commands is related to hardware or platform and requires user-defined implementation. The AT component source code `src/at_server.c` file gives the weak function definition of the migration file. The user can create a new migration file in the project to implement the following function to complete the migration interface, or modify the weak function to complete the migration interface directly in the file.
1. Device restart function: `void at_port_reset(void);`. This function completes the device soft restart function and is used to implement the basic command AT+RST in AT Server.
2. The device restores the factory settings function: `void at_port_factory_reset(void);`. This function completes the device factory reset function and is used to implement the basic command ATZ in AT Server.
3. Add a command table in the link script (add only in gcc, no need to add in Keil and IAR).
If you use the gcc toolchain in your project, you need to add the *section* corresponding to the AT server command table in the link script. Refer to the following link script:
```c
/* Constant data goes into FLASH */
.rodata :
{
...
/* section information for RT-thread AT package */
. = ALIGN(4);
__rtatcmdtab_start = .;
KEEP(*(RtAtCmdTab))
__rtatcmdtab_end = .;
. = ALIGN(4);
} > CODE
```
## AT Client
### AT Client Configuration
When using the AT Client feature in the AT component, the following configuration in rtconfig.h needs to be defined:
```c
#define RT_USING_AT
#define AT_USING_CLIENT
#define AT_CLIENT_NUM_MAX 1
#define AT_USING_SOCKET
#define AT_USING_CLI
#define AT_PRINT_RAW_CMD
```
- `RT_USING_AT`: Used to enable or disable the AT component;
- `AT_USING_CLIENT`: Used to enable the AT Client function;
- `AT_CLIENT_NUM_MAX`: Maximum number of AT clients supported at the same time.
- `AT_USING_SOCKET`: Used by the AT client to support the standard BSD Socket API and enable the AT Socket function.
- `AT_USING_CLI`: Used to enable or disable the client command line interaction mode.
- `AT_PRINT_RAW_CMD`: Used to enable the real-time display mode of AT command communication data for easy debugging.
The above configuration options can be added directly to the `rtconfig.h` file or added by the Env. The specific path in Env is as follows:
```c
RT-Thread Components --->
Network --->
AT commands --->
[*] Enable AT commands
[ ] Enable debug log output
[ ] Enable AT commands server
[*] Enable AT commands client
(1) The maximum number of supported clients
[*] Enable BSD Socket API support by AT commnads
[*] Enable command-line interface for AT commands
[ ] Enable print RAW format AT command communication data
```
After the configuration is complete, you can use the command line to rebuild the project, or use `scons` to compile.
### AT Client Initialization ###
After configuring the AT Client, you need to initialize it at startup to enable the AT Client function. If the component has been initialized automatically, no additional initialization is required. Otherwise, you need to call the following function in the initialization task:
```c
int at_client_init(const char *dev_name, rt_size_t recv_bufsz);
```
The AT Client initialization function, which belongs to the application layer function, needs to be called before using the AT Client function or using the AT Client CLI function. The `at_client_init()` function completes the initialization of the AT Client device, the initialization of the AT Client porting function, the semaphore and mutex used by the AT Client, and other resources, and creates the `at_client` thread for parsing the data received in the AT Client and for processing the URC data.
### AT Client data receiving and sending ###
The main function of the AT Client is to send AT commands, receive data, and parse data. The following is an introduction to the processes and APIs related to AT Client data reception and transmission.
Related structure definition:
```c
struct at_response
{
/* response buffer */
char *buf;
/* the maximum response buffer size */
rt_size_t buf_size;
/* the number of setting response lines
* == 0: the response data will auto return when received 'OK' or 'ERROR'
* != 0: the response data will return when received setting lines number data */
rt_size_t line_num;
/* the count of received response lines */
rt_size_t line_counts;
/* the maximum response time */
rt_int32_t timeout;
};
typedef struct at_response *at_response_t;
```
In the AT component, this structure is used to define a control block for AT command response data, which is used to store or limit the data format of the AT command response data.
- `buf` is used to store the received response data. Note that the data stored in the buf is not the original response data, but the data of the original response data removal terminator (`"\r\n"`). Each row of data in the buf is split by '\0' to make it easy to get data by row.
- `buf_size` is a user-defined length of the received data that is most supported by this response. The length of the return value is defined by the user according to his own command.
- `line_num` is the number of rows that the user-defined response data needs to receive. **If there is no response line limit requirement, it can be set to 0.**
- `line_counts` is used to record the total number of rows of this response data.
- `timeout` is the user-defined maximum response time for this response data.
`buf_size`, `line_num`, `timeout` parameters in the structure are restricted conditions, which are set when the structure is created, and other parameters are used to store data parameters for later data analysis.
Introduction to related API interfaces:
#### Create a Response Structure
```c
at_response_t at_create_resp(rt_size_t buf_size, rt_size_t line_num, rt_int32_t timeout);
```
| **Parameter** | **Description** |
|---------|-----------------------------------------|
| buf_size | Maximum length of received data supported by this response |
| line_num | This response requires the number of rows of data to be returned. The number of rows is divided by a standard terminator (such as "\r\n"). If it is 0, it will end the response reception after receiving the "OK" or "ERROR" data; if it is greater than 0, it will return successfully after receiving the data of the current set line number. |
| timeout | The maximum response time of the response data, receiving data timeout will return an error |
| **Return** | -- |
| != NULL | Successful, return a pointer to the response structure |
| = NULL | Failed, insufficient memory |
This function is used to create a custom response data receiving structure for later receiving and parsing the send command response data.
#### Delete a Response Structure
```c
void at_delete_resp(at_response_t resp);
```
| **Parameter** | **Description** |
|----|-------------------------|
| resp | The response structure pointer to be deleted |
This function is used to delete the created response structure object, which is generally paired with the **at_create_resp** creation function.
#### Set the Parameters of Response Structure
```c
at_response_t at_resp_set_info(at_response_t resp, rt_size_t buf_size, rt_size_t line_num, rt_int32_t timeout);
```
| **Parameter** | **Description** |
|---------|----------------------------------|
| resp | Response structure pointer that has been created |
| buf_size | Maximum length of received data supported by this response |
| line_num | This response requires the number of rows of data to be returned. The number of lines is divided by the standard terminator. If it is 0, the response is received after receiving the "OK" or "ERROR" data. If it is greater than 0, the data is successfully returned after receiving the data of the currently set line number. |
| timeout | The maximum response time of the response data, receiving data timeout will return an error. |
| **Return** | -- |
| != NULL | Successful, return a pointer to the response structure |
| = NULL | Failed, insufficient memory |
This function is used to set the response structure information that has been created. It mainly sets the restriction information on the response data. It is generally used after creating the structure and before sending the AT command. This function is mainly used to send commands when the device is initialized, which can reduce the number of times the response structure is created and reduce the code resource occupation.
#### Send a Command and Receive a Response
```c
rt_err_t at_exec_cmd(at_response_t resp, const char *cmd_expr, ...);
```
| **Parameter** | **Description** |
|---------|-----------------------------|
| resp | Response structure body pointer created |
| cmd_expr | Customize the expression of the input command |
| ... | Enter the command data list, a variable parameter |
| **Return** | -- |
| >=0 | Successful |
| -1 | Failed |
| -2 | Failed, receive response timed out |
This function is used by the AT Client to send commands to the AT Server and wait for a response. `resp` is a pointer to the response structure that has been created. The AT command uses the variable argument input of the match expression. **You do not need to add a command terminator at the end of the input command.**
Refer to the following code to learn how to use the above AT commands to send and receive related functions:
```c
/*
* Program listing: AT Client sends commands and receives response routines
*/
#include <rtthread.h>
#include <at.h> /* AT component header file */
int at_client_send(int argc, char**argv)
{
at_response_t resp = RT_NULL;
if (argc != 2)
{
LOG_E("at_cli_send [command] - AT client send commands to AT server.");
return -RT_ERROR;
}
/* Create a response structure, set the maximum support response data length to 512 bytes, the number of response data lines is unlimited, and the timeout period is 5 seconds. */
resp = at_create_resp(512, 0, rt_tick_from_millisecond(5000));
if (!resp)
{
LOG_E("No memory for response structure!");
return -RT_ENOMEM;
}
/* Send AT commands and receive AT Server response data, data and information stored in the resp structure */
if (at_exec_cmd(resp, argv[1]) != RT_EOK)
{
LOG_E("AT client send commands failed, response error or timeout !");
return -ET_ERROR;
}
/* Command sent successful */
LOG_D("AT Client send commands to AT Server success!");
/* Delete response structure */
at_delete_resp(resp);
return RT_EOK;
}
#ifdef FINSH_USING_MSH
#include <finsh.h>
/* Output at_Client_send to msh */
MSH_CMD_EXPORT(at_Client_send, AT Client send commands to AT Server and get response data);
#endif
```
The implementation principle of sending and receiving data is relatively simple. It mainly reads and writes the serial port device bound by the AT client, and sets the relevant number of rows and timeout to limit the response data. It is worth noting that the `res` response needs to be created first. The structure passed `in_exec_cmd` function is for data reception. When the `at_exec_cmd` function's parameter `resp` is NULL, it means that the data sent this time **does not consider processing the response data and directly returns the result**.
### AT Client Data Parsing Method ###
After the data is normally acquired, the response data needs to be parsed, which is one of the important functions of the AT Client. Parsing of data in the AT Client provides a parsed form of a custom parsing expression whose parsing syntax uses the standard `sscanf` parsing syntax. Developers can use the custom data parsing expression to respond to useful information in the data, provided that the developer needs to review the relevant manual in advance to understand the basic format of the AT Server device response data that the AT Client connects to. The following is a simple AT Client data parsing method through several functions and routines.
#### Get Response Data for the Specified Line Number
```c
const char *at_resp_get_line(at_response_t resp, rt_size_t resp_line);
```
| **Parameter** | **Description** |
|----------|-----------------------------|
| resp |Response structure pointer |
| resp_line | Required line number for obtaining data |
| **Return** | -- |
| != NULL | Successful, return a pointer to the corresponding line number data |
| = NULL | Failed, input line number error |
This function is used to get a row of data with the specified line number in the AT Server response data. The line number is judged by the standard data terminator. The above send and receive functions `at_exec_cmd` have recorded and processed the data and line numbers of the response data in the `resp` response structure, where the data information of the corresponding line number can be directly obtained.
#### Get Response Data by the Specified Keyword
```c
const char *at_resp_get_line_by_kw(at_response_t resp, const char *keyword);
```
| **Parameter** | **Description** |
|-------|-----------------------------|
| resp |Response structure pointer |
| keyword | Keyword information |
| **Return** | -- |
| != NULL | Successful, return a pointer to the corresponding line number data |
| = NULL | Failed, no keyword information found |
This function is used to get a corresponding row of data by keyword in the AT Server response data.
#### Parse Response Data for the Specified Line Number
```c
int at_resp_parse_line_args(at_response_t resp, rt_size_t resp_line, const char *resp_expr, ...);
```
| **Parameter** | **Description** |
|----------|---------------------------------|
| resp |Response structure pointer |
| resp_line | Parsed data line number required, **from the start line number count 1** |
| resp_expr | Custom parameter parsing expression |
| ... | Parsing the parameter list as a variable parameter |
| **Return** | -- |
| >0 | Successful, return the number of parameters successfully parsed |
| =0 | Failed, no parameters matching the parsing expression |
| -1 | Failed, parameter parsing error |
This function is used to get a row of data with the specified line number in the AT Server response data, and parse the parameters in the row data.
#### Parse Response Data for a Row with Specified Keyword
```c
int at_resp_parse_line_args_by_kw(at_response_t resp, const char *keyword, const char *resp_expr, ...);
```
| **Parameter** | **Description** |
|----------|---------------------------------|
| resp |Response structure pointer |
| keyword | Keyword information |
| resp_expr | Custom parameter parsing expression |
| ... | Parsing the parameter list as a variable parameter |
| **Return** | -- |
| >0 | Successful, return the number of parameters successfully parsed |
| =0 | Failed, no parameters matching the parsing expression |
| -1 | Failed, parameter parsing error |
This function is used to get a row of data containing a keyword in the AT Server response data and parse the parameters in the row data.
The data parsing syntax uses the standard `sscanf` syntax, the content of the syntax is more, developers can search their parsing syntax, here two procedures are used to introduce the simple use method.
#### Serial Port Configuration Information Analysis Example
The data sent by the client:
```c
AT+UART?
```
The response data obtained by the client:
```c
UART=115200,8,1,0,0\r\n
OK\r\n
```
The pseudo code is parsed as follows:
```c
/* Create a server response structure, the maximum length of user-defined receive data is 64 */
resp = at_create_resp(64, 0, rt_tick_from_millisecond(5000));
/* Send data to the server and receive response data in the resp structure */
at_exec_cmd(resp, "AT+UART?");
/* Analyze the serial port configuration information, 1 means parsing the first line of response data, '%*[^=]' means ignoring the data before the equal sign */
at_resp_parse_line_args(resp, 1,"%*[^=]=%d,%d,%d,%d,%d", &baudrate, &databits, &stopbits, &parity, &control);
printf("baudrate=%d, databits=%d, stopbits=%d, parity=%d, control=%d\n",
baudrate, databits, stopbits, parity, control);
/* Delete server response structure */
at_delete_resp(resp);
```
#### IP and MAC Address Resolution Example ####
The data sent by the client:
```c
AT+IPMAC?
```
The response data obtained by the server:
```c
IP=192.168.1.10\r\n
MAC=12:34:56:78:9a:bc\r\n
OK\r\n
```
The pseudo code is parsed as follows:
```c
/* Create a server response structure, the maximum length of user-defined receive data is 128 */
resp = at_create_resp(128, 0, rt_tick_from_millisecond(5000));
at_exec_cmd(resp, "AT+IPMAC?");
/* Customize the parsing expression to parse the information in the current line number data */
at_resp_parse_line_args(resp, 1,"IP=%s", ip);
at_resp_parse_line_args(resp, 2,"MAC=%s", mac);
printf("IP=%s, MAC=%s\n", ip, mac);
at_delete_resp(resp);
```
The key to parsing data is to correctly define the expression. Because the response data of the different device manufacturers is not unique to the response data of the AT device, only the form of the custom parsing expression can be obtained to obtain the required information. The design of the `at_resp_parse_line_args` parsing parameter function is based on the `sscanf` data parsing method. Before using it, the developer needs to understand the basic parsing syntax and then design the appropriate parsing syntax in combination with the response data. If the developer does not need to parse the specific parameters, you can use the `at_resp_get_line` function to get the specific data of a row.
### AT Client URC Data Processing ###
The processing of URC data is another important feature of AT Client. URC data is the data that is actively sent by the server. It cannot be received by the above data sending and receiving functions. The URC data format and function are different for different devices. Therefore, the URC data processing mode needs to be customized. The AT component provides a list management method for the processing of URC data. Users can customize the addition of URC data and its execution functions to the management list, so the processing of URC data is also the main porting work of AT Client.
Related structure:
```c
struct at_urc
{
const char *cmd_prefix; // URC data prefix
const char *cmd_suffix; // URC data suffix
void (*func)(const char *data, rt_size_t size); // URC data execution function
};
typedef struct at_urc *at_urc_t;
```
Each URC data has a structure control block that defines and determines the prefix and suffix of the URC data, as well as the execution function of the URC data. A piece of data can be defined as URC data only if it matches the prefix and suffix of the URC exactly. The URC data execution function is executed immediately after the matching URC data is obtained. So developers adding a URC data requires a custom matching prefix, suffix, and execution function.
#### URC Data List Initialization
```c
void at_set_urc_table(const struct at_urc *table, rt_size_t size);
```
| **Parameter** | **Description** |
|-----|-----------------------|
| table | URC data structure array pointer |
| size | Number of URC data |
This function is used to initialize the developer-defined URC data list, mainly used in the AT Client porting function.
The example of AT Client migration is given below. This example mainly shows the specific processing of URC data in the `at_client_port_init()` porting function. The developer can directly apply it to his own porting file, or customize the implementation function to complete the AT Client porting.
```c
static void urc_conn_func(const char *data, rt_size_t size)
{
/* WIFI connection success information */
LOG_D("AT Server device WIFI connect success!");
}
static void urc_recv_func(const char *data, rt_size_t size)
{
/* Received data from the server */
LOG_D("AT Client receive AT Server data!");
}
static void urc_func(const char *data, rt_size_t size)
{
/* Device startup information */
LOG_D("AT Server device startup!");
}
static struct at_urc urc_table[] = {
{"WIFI CONNECTED", "\r\n", urc_conn_func},
{"+RECV", ":", urc_recv_func},
{"RDY", "\r\n", urc_func},
};
int at_client_port_init(void)
{
/* Add multiple URC data to the URC list and execute the URC function when receiving data that matches both the URC prefix and the suffix */
at_set_urc_table(urc_table, sizeof(urc_table) / sizeof(urc_table[0]));
return RT_EOK;
}
```
### AT Client Other APIs Introduction
#### Send Specified Length Data
```c
rt_size_t at_client_send(const char *buf, rt_size_t size);
```
| **Parameter** | **Description** |
|----|-----------------------------|
| buf | Pointer to send data |
| size | Length of data sent |
| **Return** | -- |
| >0 | Successful, return the length of the data sent |
| <=0 | Failed |
This function is used to send the specified length data to the AT Server device through the AT Client device, which is mostly used for the AT Socket function.
#### Receive Specified Length Data
```c
rt_size_t at_client_recv(char *buf, rt_size_t size,rt_int32_t timeout);
```
| **Parameter** | **Description** |
|----|-----------------------------|
| buf | Pointer to receive data |
| size | Maximum length for receiving data |
| timeout | Receive data timeout (tick) |
| **Return** | -- |
| >0 | Successful, return the length of the data received successfully |
| <=0 | Failed, receiving data error or timeout |
This function is used to receive data of a specified length through the AT Client device, and is mostly used for the AT Socket function. This function can only be used in URC callback handlers.
#### Set the line terminator for receiving data ####
```c
void at_set_end_sign(char ch);
```
| Parameter | 描述 |
| ----- | ----- |
|ch | Line terminator |
| **Return** | **描述** |
|- | - |
This function is used to set the line terminator, which is used to judge the end of a row of data received by the client, and is mostly used for the AT Socket function.
#### Waiting for module initialization to complete ####
```c
int at_client_wait_connect(rt_uint32_t timeout);
```
| Parameter | Description |
| ----- | ----- |
|timeout | Waiting timeout |
| **Return** | **Description** |
|0 | Successful |
|<0 | Failed, no data returned during the timeout period |
This function is used to cyclically send AT commands when the AT module starts, until the module responds to the data, indicating that the module is successfully started.
### AT Client Multi-Client Support ###
In general, the device as the AT Client only connects to one AT module (the AT module acts as the AT Server) and can directly use the above functions of data transmission and reception and command parsing. In a few cases, the device needs to connect multiple AT modules as the AT Client. In this case, the multi-client support function of the device is required.
The AT component provides support for multi-client connections and provides two different sets of function interfaces: **Single-Client Mode Functions** and **Multi-Client Mode Functions**.
- Single-Client Mode Function: This type of function interface is mainly used when the device is connected to only one AT module, or when the device is connected to multiple AT modules, it is used in the **first AT client**.
- Multi-Client Mode Function: This type of function interface mainly uses devices to connect multiple AT modules.
The advantages and disadvantages of the two different mode functions and in different application scenarios are as follows:
![at client modes comparison](figures/at_multiple_client.jpg)
The single client mode function definition is mainly different from the single connection mode function. The definition of the incoming client object is different. The single client mode function uses the first initialized AT client object by default, and the multi-client mode function can pass in the user-defined custom client object. The function to get the client object is as follows:
```c
at_client_t at_client_get(const char *dev_name);
```
This function obtains the AT client object created by the device through the incoming device name, which is used to distinguish different clients when connecting multiple clients.
The single client mode and multi-client mode function interface definitions differ from the following functions:：
| Single-Client Mode Functions | Multi-Client Mode Functions |
| ----------------------------| ---------------------------------------|
| at_exec_cmd(...) | at_obj_exec_cmd(client, ...) |
| at_set_end_sign(...) | at_obj_set_end_sign(client, ...) |
| at_set_urc_table(...) | at_obj_set_urc_table(client, ...) |
| at_client_wait_connect(...) | at_client_obj_wait_connect(client, ...) |
| at_client_send(...) | at_client_obj_send(client, ...) |
| at_client_recv(...) | at_client_obj_recv(client, ...) |
The two modes of client data transmission and parsing are basically the same, and the function usage process is different, as shown below:
```c
/* Single client mode function usage */
at_response_t resp = RT_NULL;
at_client_init("uart2", 512);
resp = at_create_resp(256, 0, 5000);
/* Send commands using a single client mode function */
at_exec_cmd(resp, "AT+CIFSR");
at_delete_resp(resp);
```
```c
/* Multi-client mode functions usage */
at_response_t resp = RT_NULL;
at_client_t client = RT_NULL;
/* Initialize two AT clients */
at_client_init("uart2", 512);
at_client_init("uart3", 512);
/* Get the corresponding AT client object by name */
client = at_client_get("uart3");
resp = at_create_resp(256, 0, 5000);
/* Send commands using multi-client mode functions */
at_obj_exec_cmd(client, resp, "AT+CIFSR");
at_delete_resp(resp);
```
The process differences used by other functions are similar to the above `at_obj_exec_cmd()` function. The main function is to obtain the client object through the `at_client_get()` function, and then determine which client is the client through the incoming object to achieve multi-client support.
## FAQs
### Q: What should I do if the log on the shell shows an error when enabling the AT command to send and receive data real-time printing function. ?
**A:** Increase the baudrate of the serial port device corresponding to the shell to 921600, improve the serial port printing speed, and prevent the printing error when the data is too large.
### Q: When the AT Socket function is started, the compile prompt "The AT socket device is not selected, please select it through the env menuconfig".
**A:** After the AT Socket function is enabled, the corresponding device model is enabled in the at device package by default. Enter the at device package, configure the device as an ESP8266 device, configure WIFI information, re-generate the project, compile and download.
### Q: AT Socket function data reception timeout or data reception is not complete.
**A:** The error may be that the receive data buffer in the serial device used by the AT is too small (RT_SERIAL_RB_BUFSZ default is 64 bytes), and the data is overwritten after the data is not received in time. The buffer size of the serial port receiving data (such as 256 bytes) is appropriately increased.

BIN
documentation/at/figures/at_framework.jpg Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 7.2 KiB

BIN
documentation/at/figures/at_multiple_client.jpg Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 36 KiB

747
documentation/basic/basic.md Normal file
View file

@ -0,0 +1,747 @@
# Kernel Basics
This chapter gives a brief introduction to the software architecture of the RT-Thread kernel, beginning with its composition and implementation. While also introducing RT-Thread kernel-related concepts for beginners.
After understanding this chapter, readers will have an elementary understanding of the RT Thread kernel and will be able to answer questions such as -
- What are the constituents of the kernel?
- How does the system startup?
- How is the memory distributed?
- What are the methods of kernel configuration?
In the nutshell, this is only a brief introduction to software architecture decomposition and implementation of the real-time kernel. This will give understanding and concepts of how RT-Thread kernel works togther. After learning from this chapter, readers will have basic knowledge of each kernel components, system booting up proccesses, memory allocation and distrubtion, and methods of kernel configuration.
## **Table of Contents**
1. [Introduction to RT-Thread Kernel](#introduction-to-rt-thread-kernel)
2. [RT-Thread Startup Process](#rt-thread-startup-process)
3. [RT-Thread Program Memory Distribution](#rt-thread-program-memory-distribution)
4. [RT-Thread Automatic Initialization Mechanism](#rt-thread-automatic-initialization-mechanism)
5. [RT-Thread Kernel Object Model](#rt-thread-kernel-object-model)
## Introduction to RT-Thread Kernel
Kernel is the most basic and fundenmental part of an Operating System. Kernel service library and RT-Thread kernel libraries are interfacing between hardware and components/service layer. This includes the implementation of real-time kernel service library (rtservice.h/kservice.c) and other RT-Thread kernel libraries such as object management, thread management and scheduler, inter-thread communication management, clock management and memory management respectively. Below diagram is the core architecture diagram of the core kernel.
![RT-Thread Kernel and its Substructure](figures/03kernel_Framework.png)
Implementation of core kernel libraries are similar to a small set of standard C runtime library and it can run independently. For example, Standard C library (C runtime library) provides "strcpy", "memcpy", "printf", "scanf" and other function implementations. RT-Thread kernel libraries also provide the function implementations which are mainly used by Core Kernel. However, to avoid name conflicts, specifically functions' names are preceded with rt_.
The built of the Kernel will be vary depending on the complier. For example, using GNU GCC compiler, it will use more implementation from the standard C library. Last but not least, the minimum resource requirements of the Kernel is 3KB ROM and 1.2KB RAM.
### Thread Scheduling
Thread is the smallest scheduling unit in the RT-Thread operating system. The thread scheduling algorithm is a **Priority-based Full Preemptive Multi-Thread** scheduling algorithm.
The system can support up to 256(0 - 255) thread priorities. For systems with tight resources, configurations with 8 or 32 thread priorities can be chosen(For example, STM32 has 32 thread priorities as per the default configuration). Lower numbers have a higher priority where 0 represents the highest priority furthermore the lowest priority(highest number) is reserved for idle threads.
RT-Thread supports the creation of multiple threads with the same priority. Threads having the same priority are scheduled with a Time Slice Rotation Scheduling algorithm so that each thread runs for the same amount of time.
The number of threads is bounded by the memory of the hardware platform and not the system.
Thread management will be covered in detail in the "Thread Management" chapter.
### Clock Management
RT-Thread's Clock management is based upon a **clock beat**, which is the smallest clock unit in the RT-Thread operating system.
The RT-Thread timer provides two types of timer mechanisms:
- **One-Shot Timer** - Triggers only one timer event after startup and then stops automatically.
- **Periodic Trigger Timer** - Periodically triggers timer events until the user manually stops the timer or it will continue to operate.
The RT-Thread timer can be set to the `HARD_TIMER` or the `SOFT_TIMER` mode depending on the context in which the timeout function is executed.
The timer service is concluded using a timer timing callback i.e. a timeout function. The user can select the appropriate type of timer according to their real-time requirements for timing processing.
Timer will be explained further in the "Clock Management" chapter.
### Synchronization between Threads
RT-Thread uses thread semaphores, mutexes, and event sets to achieve inter-thread synchronization.
Thread synchronizations happen through the acquisition and release of semaphore and mutexes.
The mutex uses priority inheritance to solve the common priority inversion problem in the real-time system. The thread synchronization mechanism allows threads to wait according to priorities or to acquire semaphores/mutexes following the First In First Out(FIFO) method.
Event sets are primarily used for synchronization between threads, they can achieve one-to-many and many-to-many synchronization. It allows "**OR** trigger"(*independent synchronization*) and "**AND** trigger"(*associative synchronization*) suitable for situations where threads are waiting for multiple events.
The concepts of semaphores, mutexes, and event sets are detailed in the "Inter-Thread Synchronization" chapter.
### Inter-Thread Communication
RT-Thread supports communication mechanisms such as mailbox, message queue, etc. The mailbox's message length is fixed to 4 bytes. Whereas, message queue can receive messages in variable size and cache the messages in its own memory space.
Compared to a message queue, a mailbox is more efficient. The sending action of the mailbox and message queue can be safely used in an ISR (Interrupt Service Routine). The communication mechanism allows threads to wait by priority or to acquire by the First In First Out (FIFO) method.
The concept of mailbox and message queue will be explained in detail in the "Inter-Thread Communication" chapter.
### Memory Management
RT-Thread allows:
1. Static Memory Pool
2. Dynamic Memory Pool
When the static memory pool has available memory, the time allocated to the memory block will be constant.
When the static memory pool is empty, the system will then request for suspending or blocking the thread of the memory block. The thread will abandon the request and return if the memory block is not obtained after waiting for a while, or the thread will abandon and return immediately. The waiting time depends on the waiting time parameter set when the memory block is applied. When other threads release the memory block to the memory pool, the system will wake up the thread if there are suspended threads waiting to be allocated of memory blocks.
Under circumstances of different system resources, the dynamic memory heap management module respectively provides memory management algorithms for small memory systems and SLAB memory management algorithms for large memory systems.
There is also a dynamic memory heap management called memheap, suitable for memory heaps in systems with multiple addresses that can be discontinuous. Using memheap, the user can "paste" multiple memory heaps together, letting them operate as if operating a memory heap.
The concept of memory management will be explained in the "Memory Management" chapter.
### I/O Device Management
RT-Thread uses I2C, SPI, USB, UART, etc., as peripheral devices and is uniformly registered through the device. It realized a device management subsystem accessed by the name, and it can access hardware devices according to a unified API interface. On the device driver interface, depending on the characteristics of the embedded system, corresponding events can be attached to different devices. The driver notifies the upper application program when the device event is triggered.
The concept of I/O device management will be explained in the "Device Model" and "General Equipment" chapters.
## RT-Thread Startup Process
The understanding of most codes usually starts from learning the startup process. We will firstly look for the source of the startup. Taking MDK-ARM as an example, the user program entry for MDK-ARM is the main() function located in the main.c file. The launching of the system starts from the assembly code startup_stm32f103xe.s, jumps to the C code, initializes the RT-Thread system function, and finally enters the user program entry main().
To complete the RT-Thread system function initialization before entering main(), we used the MDK extensions `$Sub$$` and `$Super$$`. Users can add the prefix of `$Sub$$` to main to make it a new function `$Sub$$main`.
`$Sub$$main` can call some functions to be added before main (here, RT-Thread system initialization function is added). Then, call `$Super$$main` to the main() function so that the user does not have to manage the system initialization before main().
For more information on the use of the `$Sub$$` and `$Super$$`extensions, see the ARM® Compiler v5.06 for μVision®armlink User Guide.
Let's take a look at this code defined in components.c:
```c
/* $Sub$$main Function */
int $Sub$$main(void)
{
rtthread_startup();
return 0;
}
```
Here, the `$Sub$$main` function simply calls the rtthread_startup() function. RT-Thread allows multiple platforms and multiple compilers, and the rtthread_startup() function is a uniform entry point specified by RT-Thread, so the `$Sub$$main` function only needs to call the rtthread_startup() function (RT-Thread compiled using compiler GNU GCC is an example where it jumps directly from the assembly startup code section to the rtthread_startup() function and starts the execution of the first C code).
The rtthread_startup() function can be found in the code of components.c, the startup process of RT-Thread is as shown below:
![System startup process](figures/03Startup_process.png)
Code for the rtthread_startup() function is as follows:
```c
int rtthread_startup(void)
{
rt_hw_interrupt_disable();
/* Board level initialization: system heap initialization is required inside the function */
rt_hw_board_init();
/* Print RT-Thread version information */
rt_show_version();
/* Timer initialization */
rt_system_timer_init();
/* Scheduler initialization */
rt_system_scheduler_init();
#ifdef RT_USING_SIGNALS
/* Signal initialization */
rt_system_signal_init();
#endif
/* Create a user main() thread here */
rt_application_init();
/* Timer thread initialization */
rt_system_timer_thread_init();
/* Idle thread initialization */
rt_thread_idle_init();
/* Start scheduler */
rt_system_scheduler_start();
/* Will not execute till here */
return 0;
}
```
This part of the startup code can be roughly divided into four parts:
1. Initialize hardware related to the system.
2. Initialize system kernel objects, such as timers, schedulers, and signals.
3. Create the main thread initialize various modules in the main thread one by one.
4. Initialize the timer thread, idle thread, and start the scheduler.
Set the system clock in rt_hw_board_init() to provide heartbeat and serial port initialization for the system, bound to the system's input and output terminals to this serial port. Subsequent system operation information will be printed out from the serial port later.
The main() function is the user code entry for RT-Thread, and users can add their own applications to the main() function.
```c
int main(void)
{
/* user app entry */
return 0;
}
```
## RT-Thread Program Memory Distribution
The general MCU contains storage space that includes the on-chip Flash and the on-chip RAM. RAM is equivalent to memory, and Flash is comparable to a hard disk. The compiler classifies a program into several parts stored in different memory areas of the MCU.
After the Keil project is compiled, there will be a prompt stating the occupied space by the corresponding program, for example:
```
linking...
Program Size: Code=48008 RO-data=5660 RW-data=604 ZI-data=2124
After Build - User command \#1: fromelf --bin.\\build\\rtthread-stm32.axf--output rtthread.bin
".\\build\\rtthread-stm32.axf" - 0 Error(s), 0 Warning(s).
Build Time Elapsed: 00:00:07
```
The Program Size mentioned above contains the following sections:
1. **Code**: Code Segment, section of code that stores the program
2. **RO-data**: Read-Only data segment, stores the constants defined in the program
3. **RW-data**: Read and Write data segment, stores global variables initialized to non-zero values
4. **ZI-data**: 0 data segment, stores uninitialized global variables and initialized-to-0 variables
After compiling the project, there will be a generated .map file that describes the size and address of each function. The last few lines of the file also illustrate the relationship between the above fields:
```
Total RO Size (Code + RO Data) 53668 ( 52.41kB)
Total RW Size (RW Data + ZI Data) 2728 ( 2.66kB)
Total ROM Size (Code + RO Data + RW Data) 53780 ( 52.52kB)
```
1. RO Size contains Code and RO-data, indicating the size of the Flash occupied by the program
2. RW Size contains RW-data and ZI-data, indicating the size of the RAM occupied when operating
3. ROM Size contains Code, RO Data, and RW Data. Indicating the size of the Flash occupied by the programming system;
Before the program runs, the file entity needs to be flashed into the STM32 Flash, usually a bin or hex file. The burned file is called an executable image file. The left part in the figure below shows the memory distribution after the executable image file is flashed into STM32 which includes the RO and RW segments. The RO segment stores data of Code and RO-data, and the RW segment holds the data of RW-data. Since ZI-data is 0, it is not included in the image file.
STM32 is launched from Flash by default after power-on. After launching, RW-data (initialized global variable) the RW segment is transferred to RAM, but the RO segment is not transferred. Meaning the execution code of the CPU is read from the Flash. The ZI segment is allocated according to the ZI address and size is given by the compiler, and the RAM area is cleared.
![RT-Thread Memory Distribution](figures/03Memory_distribution.png)
The dynamic memory heap is unused RAM space, and the memory blocks requested and released by the application come from this space.
Like the following example:
```c
rt_uint8_t* msg_ptr;
msg_ptr = (rt_uint8_t*) rt_malloc (128);
rt_memset(msg_ptr, 0, 128);
```
The 128-byte memory space pointed by the `msg_ptr` pointer in the code is in the dynamic memory heap space.
Some global variables are stored in the RW segment and the ZI segment. The RW segment holds the global variable with the initial value (the global variable in the constant form is placed in the RO segment, which is a read-only property), and uninitialized global variable is stored in the ZI segment, as in the following example:
```c
#include <rtthread.h>
const static rt_uint32_t sensor_enable = 0x000000FE;
rt_uint32_t sensor_value;
rt_bool_t sensor_inited = RT_FALSE;
void sensor_init()
{
/* ... */
}
```
The `sensor_value` is stored in the ZI segment and is automatically initialized to zero after system startup (some library functions provided by the user program or compiler are initialized to zero). The sensor_inited variable is stored in the RW segment, and the sensor_enable is stored in the RO segment.
## RT-Thread Automatic Initialization Mechanism
The automatic initialization mechanism means that the initialization function does not need to be called by explicit function. It only needs to be declared by macro definition at the function definition, and it will be executed during system startup.
For example, calling a macro definition in the serial port driver to inform the function that needs to be called to initialize the system. The code is as follows:
```c
int rt_hw_usart_init(void) /* Serial port initialization function */
{
... ...
/* Register serial port 1 device */
rt_hw_serial_register(&serial1, "uart1",
RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX,
uart);
return 0;
}
INIT_BOARD_EXPORT(rt_hw_usart_init); /* Use component auto-initialization mechanism */
```
The last part of the sample code INIT_BOARD_EXPORT(rt_hw_usart_init) indicates that the automatic initialization function is used. In this way, rt_hw_usart_init() function is automatically called by the system, so where is it called?
In the system startup flowchart, there are two functions: rt_components_board_init() and rt_components_init(), subsequent functions inside the box with the underlying color represent functions that are automatically initialized, where:
1. “board init functions” are all initialization functions declared by INIT_BOARD_EXPORT(fn).
2. “pre-initialization functions” are all initialization functions declared by INIT_PREV_EXPORT(fn).
3. “device init functions” are all initialization functions declared by INIT_DEVICE_EXPORT(fn).
4. “components init functions” are all initialization functions declared by INIT_COMPONENT_EXPORT(fn).
5. “enviroment init functions” are all initialization functions declared by INIT_ENV_EXPORT(fn).
6. “application init functions” are all initialization functions declared by INIT_APP_EXPORT(fn).
The rt_components_board_init() function executes earlier, mainly to initialize the relevant hardware environment. When this function is executed, it will traverse the initialization function table declared by INIT_BOARD_EXPORT(fn) and call each function.
The rt_components_init() function is called and executed in the main thread created after the operating system is running. At this time, the hardware environment and the operating system have been initialized and the application-related code can be executed. The rt_components_init() function will transverse through the remaining few initialization function tables declared by macros.
RT-Thread's automatic initialization mechanism uses a custom RTI symbol segment, it puts the function pointer that needs to be initialized at startup into this segment and forms an initialization function table which will be traversed during system startup. It calls the functions in the table to achieve the purpose of automatic initialization.
The macro interface definitions used to implement the automatic initialization function are described in the following table:
|Initialization sequence|Macro Interface |Description |
|----------------|------------------------------------|----------------------------------------------|
| 1 | INIT_BOARD_EXPORT(fn) | Very early initialization, the scheduler has not started yet. |
| 2 | INIT_PREV_EXPORT(fn) | Mainly used for pure software initialization, functions without too many dependencies |
| 3 | INIT_DEVICE_EXPORT(fn) | Peripheral driver initialization related, such as network card devices |
| 4 | INIT_COMPONENT_EXPORT(fn) | Component initialization, such as file system or LWIP |
| 5 | INIT_ENV_EXPORT(fn) | System environment initialization, such as mounting file systems |
| 6 | INIT_APP_EXPORT(fn) | Application initialization, such as application GUI |
Initialization function actively declares through these macro interfaces, such as INIT_BOARD_EXPORT (rt_hw_usart_init), the linker will automatically collect all the declared initialization functions, placed in the RTI symbol segment, the symbol segment is located in the RO segment of the memory distribution. All functions in this RTI symbol segment are automatically called when the system is initialized.
RT-Thread Kernel Object Model
---------------------
### Static and Dynamic Objects
The RT-Thread kernel is designed with object-oriented method. The system-level infrastructures are all kernel objects such as threads, semaphores, mutexes, timers, and more. Kernel objects fall into two categories: static kernel objects and dynamic kernel objects. Static kernel objects are usually placed in RW and ZI segments, initialized in the program after system startup; dynamic kernel objects are created from the memory heap and then manually initialized.
The following code is an example of static threads and dynamic threads:
```c
/* Thread 1 object and stack used while running */
static struct rt_thread thread1;
static rt_uint8_t thread1_stack[512];
/* Thread 1 entry */
void thread1_entry(void* parameter)
{
int i;
while (1)
{
for (i = 0; i < 10; i ++)
{
rt_kprintf("%d\n", i);
/* Delay 100ms */
rt_thread_mdelay(100);
}
}
}
/* Thread 2 entry */
void thread2_entry(void* parameter)
{
int count = 0;
while (1)
{
rt_kprintf("Thread2 count:%d\n", ++count);
/* Delay 50ms */
rt_thread_mdelay(50);
}
}
/* Thread routine initialization */
int thread_sample_init()
{
rt_thread_t thread2_ptr;
rt_err_t result;
/* Initialize thread 1 */
/* The thread entry is thread1_entry and the parameter is RT_NULL
* Thread stack is thread1_stack
* Priority is 200 and time slice is 10 OS Tick
*/
result = rt_thread_init(&thread1,
"thread1",
thread1_entry, RT_NULL,
&thread1_stack[0], sizeof(thread1_stack),
200, 10);
/* Start thread */
if (result == RT_EOK) rt_thread_startup(&thread1);
/* Create thread 2 */
/* The thread entry is thread2_entry and the parameter is RT_NULL
* Stack space is 512, priority is 250, and time slice is 25 OS Tick
*/
thread2_ptr = rt_thread_create("thread2",
thread2_entry, RT_NULL,
512, 250, 25);
/* Start thread */
if (thread2_ptr != RT_NULL) rt_thread_startup(thread2_ptr);
return 0;
}
```
In this example, thread1 is a static thread object and thread2 is a dynamic thread object. The memory space of the thread1 object, including the thread control block thread1 and the stack space thread1_stack are all determined while compiling, because there is no initial value in the code and they are uniformly placed in the uninitialized data segment. The space used by thread2 is dynamically allocated includes the thread control block (the content pointed to by thread2_ptr) and the stack space.
Static objects take up RAM space and is not depend on the memory heap manager. When allocating static objects, the time needed is determined. Dynamic objects depend on the memory heap manager. It requests RAM space while running. When the object is deleted, the occupied RAM space is released. These two methods have their own advantages and disadvantages, and can be selected according to actual needs.
### Kernel Object Management Structure
RT-Thread uses the kernel object management system to access/manage all kernel objects. Kernel objects contain most of the facilities in the kernel. These kernel objects can be statically allocated static objects and dynamic objects allocated from the system memory heap. .
Because of this design for kernel object, RT-Thread is able to not depend on the specific memory allocation method, and the flexibility of the system is greatly improved.
RT-Thread kernel objects include: threads, semaphores, mutexes, events, mailboxes, message queues and timers, memory pools, device drivers, and more. The object container contains information about each type of kernel object, including object type, size, and so on. The object container assigns a linked list to each type of kernel object. All kernel objects are linked to the linked list. The kernel object container and linked list of RT-Thread are shown in the following figure:
![RT-Thread Kernel Object Container and Linked List](figures/03kernel_object.png)
The following figure shows the derivation and inheritance relationships of various kernel objects in RT-Thread. For each specific kernel object and object control block, in addition to the basic structure, they have their own extended attributes (private attributes). Take thread control block for an example, the base object is extended, attributes like thread state, precedence and so on are added. These attributes are not used in the operation of the base class object and are only used in operations related to a specific thread. Therefore, from the object-oriented point of view, each concrete object can be considered as a derivative of an abstract object, inheriting the attributes of the base object and extending the attributes related to itself.
![RT-Thread Kernel Object Inheritance Relationship](figures/03kernel_object2.png)
In the object management module, a common data structure is defined to store the common attributes of various objects. Each specific object only needs to add some special attributes of its own and its own feature will be clearly expressed.
The advantages of this design approach are:
(1) Improve the reusability and scalability of the system. It is easy to add new object categories. It only needs to inherit the attributes of the general object and add a small amount of extension.
(2) Provide a unified object operation mode, simplify the operation of various specific objects, and improve the reliability of the system.
Derivations from object control block rt_object in the above figure includes: thread object, memory pool object, timer object, device object and IPC object (IPC: Inter-Process Communication. In RT-Thread real-time operating system, IPC objects is used for synchronization and communicate between threads); derivations from IPC objects includes: semaphores, mutexes, events, mailboxes, message queues, signals, etc.
### Object Control Block
Data structure of kernel object control block:
```c
struct rt_object
{
/* Kernel object name */
char name[RT_NAME_MAX];
/* Kernel object type */
rt_uint8_t type;
/* Parameters to the kernel object */
rt_uint8_t flag;
/* Kernel object management linked list */
rt_list_t list;
};
```
Types currently supported by kernel objects are as follows:
```c
enum rt_object_class_type
{
RT_Object_Class_Thread = 0, /* Object is thread type */
#ifdef RT_USING_SEMAPHORE
RT_Object_Class_Semaphore, /* Object is semaphore type */
#endif
#ifdef RT_USING_MUTEX
RT_Object_Class_Mutex, /* Object is mutex type */
#endif
#ifdef RT_USING_EVENT
RT_Object_Class_Event, /* Object is event type */
#endif
#ifdef RT_USING_MAILBOX
RT_Object_Class_MailBox, /* Object is mailbox type */
#endif
#ifdef RT_USING_MESSAGEQUEUE
RT_Object_Class_MessageQueue, /* Object is message queue type */
#endif
#ifdef RT_USING_MEMPOOL
RT_Object_Class_MemPool, /* Object is memory pool type */
#endif
#ifdef RT_USING_DEVICE
RT_Object_Class_Device, /* Object is device type */
#endif
RT_Object_Class_Timer, /* Object is timer type */
#ifdef RT_USING_MODULE
RT_Object_Class_Module, /* Object is module */
#endif
RT_Object_Class_Unknown, /* Object is unknown */
RT_Object_Class_Static = 0x80 /* Object is a static object */
};
```
From the above type specification, we can see that if it is a static object, the highest bit of the object type will be 1 (which is the OR operation of RT_Object_Class_Static and other object types and operations). Otherwise it will be dynamic object, and the maximum number of object classes that the system can accommodate is 127.
### Kernel Object Management
Data structure of kernel object container:
```c
struct rt_object_information
{
/* Object type */
enum rt_object_class_type type;
/* Object linked list */
rt_list_t object_list;
/* Object size */
rt_size_t object_size;
};
```
A class of objects is managed by an rt_object_information structure, and each practical instance of such type of object is mounted to the object_list in the form of a linked list. The memory block size of this type of object is identified by object_size (the memory block each practical instance of each type of object is the same size).
#### Initialization Object
An uninitialized static object must be initialized before it can be used. The initialization object uses the following interfaces:
```c
void rt_object_init(struct rt_object* object ,
enum rt_object_class_type type ,
const char* name)
```
When this function is called to initialize the object, the system will place the object into the object container for management, that is, initialize some parameters of the object, and then insert the object node into the object linked list of the object container. Input parameters of the function is described in the following table:
|Parameters|Description |
| -------- | ------------------------------------------------------------ |
| object | The object pointer that needs to be initialized must point to a specific object memory block, not a null pointer or a wild pointer. |
| type | The type of the object must be a enumeration type listed in rt_object_class_type, RT_Object_Class_Static excluded. (For static objects, or objects initialized with the rt_object_init interface, the system identifies it as an RT_Object_Class_Static type) |
| name | Name of the object. Each object can be set to a name, and the maximum length for the name is specified by RT_NAME_MAX. The system does not care if it uses ’`\0`’as a terminal symbol. |
#### Detach Object
Detach an object from the kernel object manager. The following interfaces are used to detach objects:
```c
void rt_object_detach(rt_object_t object);
```
Calling this interface makes a static kernel object to be detached from the kernel object container, meaning the corresponding object node is deleted from the kernel object container linked list. After the object is detached, the memory occupied by the object will not be released.
#### Allocate object
The above descriptions are interfaces of objects initialization and detachment, both of which are under circumstances that object-oriented memory blocks already exist. But dynamic objects can be requested when needed. The memory space is freed for other applications when not needed. To request assigning new objects, you can use the following interfaces:
```c
rt_object_t rt_object_allocate(enum rt_object_class_typetype ,
const char* name)
```
When calling the above interface, the system first needs to obtain object information according to the object type (especially the size information of the object type for the system to allocate the correct size of the memory data block), and then allocate memory space corresponding to the size of the object from the memory heap. Next, to start necessary initialization for the object, and finally insert it into the object container linked list in which it is located. The input parameters for this function are described in the following table:
|Parameters |Description |
| ------------------ | ------------------------------------------------------------ |
| type | The type of the allocated object can only be of type rt_object_class_type other than RT_Object_Class_Static. In addition, the type of object allocated through this interface is dynamic, not static. |
| name | Name of the object. Each object can be set to a name, and the maximum length for the name is specified by RT_NAME_MAX. The system does not care if it uses ’`\0`’as a terminal symbol. |
|**Return** | —— |
| object handle allocated successfully | Allocate successfully |
| RT_NULL | Fail to allocate |
#### Delete Object
For a dynamic object, when it is no longer used, you can call the following interface to delete the object and release the corresponding system resources:
```c
void rt_object_delete(rt_object_t object);
```
When the above interface is called, the object is first detached from the object container linked list, and then the memory occupied by the object is released. The following table describes the input parameters of the function:
|Parameter|Description |
|----------|------------|
| object | object handle |
#### Identify objects
Identify whether the specified object is a system object (static kernel object). The following interface is used to identify the object:
```c
rt_err_t rt_object_is_systemobject(rt_object_t object);
```
Calling the rt_object_is_systemobject interface can help to identify whether an object is a system object. In RT-Thread operating system, a system object is also a static object, RT_Object_Class_Static bit is set to 1 on the object type identifier. Usually, objects that are initialized using the rt_object_init() method are system objects. The input parameters for this function are described in the following table:
Input parameter of rt_object_is_systemobject()
|**Parameter**|Description |
|----------|------------|
| object | Object handle |
RT-Thread Kernel Configuration Example
----------------------
An important feature of RT-Thread is its high degree of tailorability, which allows for fine-tuning of the kernel and flexible removal of components.
Configuration is mainly done by modifying the file under project directory - rtconfig.h. User can conditionally compile the code by opening/closing the macro definition in the file, and finally achieve the purpos e of system configuration and cropping, as follows:
（1）RT-Thread Kernel part
```c
/* Indicates the maximum length of the name of the kernel object. If the maximum length of the name of the object in the code is greater than the length of the macro definition,
* the extra part will be cut off. */
#define RT_NAME_MAX 8
/* Set the number of aligned bytes when bytes are aligned. Usually use ALIGN(RT_ALIGN_SIZE) for byte alignment.*/
#define RT_ALIGN_SIZE 8
/* Define the number of system thread priorities; usually define the priority of idle threads with RT_THREAD_PRIORITY_MAX-1 */
#define RT_THREAD_PRIORITY_MAX 32
/* Define the clock beat. When it is 100, it means 100 tick per second, and a tick is 10ms. */
#define RT_TICK_PER_SECOND 100
/* Check if the stack overflows, if not defined, close. */
#define RT_USING_OVERFLOW_CHECK
/* Define this macro to enable debug mode, if not defined, close. */
#define RT_DEBUG
/* When debug mode is enabled: When the macro is defined as 0, the print component initialization information is turned off. When it is defined as 1, it is enabled. */
#define RT_DEBUG_INIT 0
/* When debug mode is enabled: When the macro is defined as 0, the print thread switching information is turned off. When it is defined as 1, it is enabled. */
#define RT_DEBUG_THREAD 0
/* Defining this macro means the use of the hook function is started, if not defined, close. */
#define RT_USING_HOOK
/* Defines the stack size of idle threads. */
#define IDLE_THREAD_STACK_SIZE 256
```
（2）Inter-thread synchronization and communication part, the objects that will be used in this part are semaphores, mutexes, events, mailboxes, message queues, signals, and so on.
```c
/* Define this macro to enable the use of semaphores, if not defined, close. */
#define RT_USING_SEMAPHORE
/* Define this macro to enable the use of mutexes, if not defined, close. */
#define RT_USING_MUTEX
/* Define this macro to enable the use of events, if not defined, close. */
#define RT_USING_EVENT
/* Define this macro to enable the use of mailboxes, if not defined, close. */
#define RT_USING_MAILBOX
/* Define this macro to enable the use of message queues, if not defined, close. */
#define RT_USING_MESSAGEQUEUE
/* Define this macro to enable the use of signals, if not defined, close. */
#define RT_USING_SIGNALS
```
（3）Memory Management Part
```c
/* Start the use of static memory pool */
#define RT_USING_MEMPOOL
/* Define this macro to start the concatenation of two or more memory heap , if not defined, close. */
#define RT_USING_MEMHEAP
/* Start algorithm for small memory management */
#define RT_USING_SMALL_MEM
/* Turn off SLAB memory management algorithm */
/* #define RT_USING_SLAB */
/* Start the use of heap */
#define RT_USING_HEAP
```
（4）Kernel Device Object
```c
/* Indicates the start of useing system devices */
#define RT_USING_DEVICE
/* Define this macro to start the use of system console devices, if not defined, close. */
#define RT_USING_CONSOLE
/* Define the buffer size of the console device. */
#define RT_CONSOLEBUF_SIZE 128
/* Name of the console device. */
#define RT_CONSOLE_DEVICE_NAME "uart1"
```
（5）Automatic Initialization Method
```c
/* Define this macro to enable automatic initialization mechanism, if not defined, close. */
#define RT_USING_COMPONENTS_INIT
/* Define this macro to set application entry as main function */
#define RT_USING_USER_MAIN
/* Define the stack size of the main thread */
#define RT_MAIN_THREAD_STACK_SIZE 2048
```
（6）FinSH
```c
/* Define this macro to start the use of the system FinSH debugging tool, if not defined, close. */
#define RT_USING_FINSH
/* While starting the system FinSH: the thread name is defined as tshell */
#define FINSH_THREAD_NAME "tshell"
/* While turning the system FinSH: use history commands. */
#define FINSH_USING_HISTORY
/* While turning the system FinSH: define the number of historical command lines. */
#define FINSH_HISTORY_LINES 5
/* While turning the system FinSH: define this macro to open the Tab key, if not defined, close. */
#define FINSH_USING_SYMTAB
/* While turning the system FinSH: define the priority of the thread. */
#define FINSH_THREAD_PRIORITY 20
/* While turning the system FinSH：define the stack size of the thread. */
#define FINSH_THREAD_STACK_SIZE 4096
/* While turning the system FinSH：define the length of command character. */
#define FINSH_CMD_SIZE 80
/* While turning the system FinSH: define this macro to enable the MSH function. */
#define FINSH_USING_MSH
/* While turning the system FinSH：when MSH function is enabled, macro is defined to use the MSH function by default. */
#define FINSH_USING_MSH_DEFAULT
/* While turning the system FinSH：define this macro to use only the MSH function. */
#define FINSH_USING_MSH_ONLY
```
（7）About MCU
```c
/* Define the MCU used in this project is STM32F103ZE; the system defines the chip pins by defining the chip type. */
#define STM32F103ZE
/* Define the clock source frequency. */
#define RT_HSE_VALUE 8000000
/* Define this macro to enable the use of UART1. */
#define RT_USING_UART1
```
>In practice, the system configuration file rtconfig.h is automatically generated by configuration tools and does not need to be changed manually.
Common Macro Definition Description
--------------
Macro definitions are often used in RT-Thread. For example, some common macro definitions in the Keil compilation environment:
1）rt_inline, definition is as follows, static keyword is to make the function only available for use in the current file; inline means inline, after modification using static, the compiler is recommended to perform inline expansion when calling the function.
```c
#define rt_inline static __inline
```
2）rt_used，definition is as follows, the purpose of this macro is to explain to the compiler that this code is useful, compilation needs to be saved even if it is not called in the function. For example, RT-Thread auto-initialization uses custom segments, using rt_used will retain custom code snippets.
```c
#define rt_used __attribute__((used))
```
3）RT_UNUSED，definition is as follows, indicates that a function or variable may not be used. This attribute prevents the compiler from generating warnings.
```c
#define RT_UNUSED __attribute__((unused))
```
4）rt_weak，definition is as follows, often used to define functions, when linking the function, the compiler will link the function without the keyword prefix first and link the function modified by weak if it can't find those functions.
```c
#define rt_weak __weak
```
5）ALIGN(n)，definition is as follows, is used to align its stored address with n bytes when allocating an address space to an object. Here, n can be the power of 2. Byte alignment not only facilitates quick CPU access, but also save memory space if byte alignment is properly used.
```c
#define ALIGN(n) __attribute__((aligned(n)))
```
6）RT_ALIGN(size,align)，definition is as follows, to increase size to a multiple of an integer defined by align. For example, RT_ALIGN(13,4) will return to 16.
```c
#define RT_ALIGN(size, align) (((size) + (align) - 1) & ~((align) - 1))
```

BIN
documentation/basic/figures/03Memory_distribution.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 18 KiB

BIN
documentation/basic/figures/03Startup_process.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 52 KiB

BIN
documentation/basic/figures/03kernel_Framework.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 58 KiB

BIN
documentation/basic/figures/03kernel_object.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 15 KiB

BIN
documentation/basic/figures/03kernel_object2.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 16 KiB

318
documentation/contribution_guide/coding_style_cn.md Normal file
View file

@ -0,0 +1,318 @@
# RT-Thread 编程风格
这是一份 RT-Thread 开发人员的开发指引。RT-Thread 做为一份开源软件，它需要由不同的人采用合作的方式完成，这份文档是开发人员的一个指引。RT-Thread 的开发人员请遵守这样的编程风格。同时对于使用 RT-Thread 的用户，也可通过这份文档了解 RT-Thread代码内部一些约定从而比较容易的把握到 RT-Thread 的实现方式。
## 1.目录名称
目录名称如果无特殊的需求，请使用全小写的形式；目录名称应能够反映部分的意思，例如各芯片移植由其芯片名称构成或芯片类别构成；components 目录下能够反映组件的意义。
## 2.文件名称
文件名称如果无特殊的需求(如果是引用其他地方，可以保留相应的名称)，请使用全小写的形式。另外为了避免文件名重名的问题，一些地方请尽量不要使用通用化、使用频率高的名称。
设备驱动源码文件：`drv_class.c` 的命名方式，如：
- drv_spi.c
- drv_gpio.c
## 3.头文件定义
C 语言头文件为了避免多次重复包含，需要定义一个符号。这个符号的定义形式请采用如下的风格：
```c
#ifndef __FILE_H__
#define __FILE_H__
/* header file content */
#endif
```
即定义的符号两侧采用 "__" 以避免重名，另外也可以根据文件名中是否包含多个词语而采用 "_" 连接起来。
## 4.文件头注释
在每个源文件文件头上，应该包括相应的版权信息，Change Log 记录：
```c
/*
* Copyright (c) 2006-2020, RT-Thread Development Team
*
* SPDX-License-Identifier: Apache-2.0
*
* Change Logs:
* Date Author Notes
* 2006-03-18 Bernard the first version
* 2006-04-26 Bernard add semaphore APIs
*/
```
例如采用如上的形式。
## 5.结构体定义
结构体名称请使用小写英文名的形式，单词与单词之间采用 "_" 连接，例如：
```c
struct rt_list_node
{
struct rt_list_node *next;
struct rt_list_node *prev;
};
```
其中，**"{"，"}" 独立占用一行**，后面的成员定义使用缩进的方式定义。
结构体等的类型定义请以结构体名称加上 "_t" 的形式作为名称，例如：
```c
typedef struct rt_list_node rt_list_t;
```
因为内核中对象引用方便的缘故，采用了对象内核指针作为类型定义的形式，例如：
```c
typedef struct rt_timer* rt_timer_t;
```
## 6.宏定义
在RT-Thread中，请使用大写英文名称作为宏定义，单词之间使用 "_" 连接，例如：
```c
#define RT_TRUE 1
```
## 7.函数名称、声明
函数名称请使用小写英文的形式，单词之间使用 "_" 连接。提供给上层应用使用的 API接口，必须在相应的头文件中声明；如果函数入口参数是空，必须使用 void 作为入口参数，例如：
```c
rt_thread_t rt_thread_self(void);
```
内部静态函数命名：以下划线开头，使用 `_class_method` 格式，不携带`_rt_`开头，如内核或驱动文件中的函数命名：
```c
/* IPC object init */
static rt_err_t _ipc_object_init()
/* UART driver ops */
static rt_err_t _uart_configure()
static rt_err_t _uart_control()
```
调用注册设备接口的函数命名：使用 `rt_hw_class_init()` 格式，举例：
```c
int rt_hw_uart_init(void)
int rt_hw_spi_init(void)
```
## 8.注释编写
请使用**英文**做为注释，使用中文注释将意味着在编写代码时需要来回不停的切换中英文输入法从而打断编写代码的思路。并且使用英文注释也能够比较好的与中国以外的技术者进行交流。
**语句注释**：
源代码的注释不应该过多，更多的说明应该是代码做了什么，仅当个别关键点才需要一些相应提示性的注释以解释一段复杂的算法它是如何工作的。对语句的注释只能写在它的**上方或右方**，其他位置都是非法的。
```c
/* 你的英文注释 */
```
**函数注释**：
注释以 `/**` 开头，以 ` */` 结尾，中间写入函数注释，组成元素如下，每个元素描述之间空一行，且首列对齐：
- @brief + 简述函数作用。在描述中，着重说明该函数的作用，每句话首字母大写，句尾加英文句号。
- @note + 函数说明。在上述简述中未能体现到的函数功能或作用的一些点，可以做解释说明，每句话首字母大写，句尾加英文句号。
- @see + 相关 API 罗列。若有与当前函数相关度较高的 API，可以进行列举。
- @param + 以参数为主语 + be 动词 + 描述，说明参数的意义或来源。
- @return + 枚举返回值 + 返回值的意思，若返回值为数据，则直接介绍数据的功能。
- @warning + 函数使用注意要点。在函数使用时，描述需要注意的事项，如使用环境、使用方式等。每句话首字母大写，句尾加英文句号。
注释模版请参见：rt-thread/src/ipc.c 源码文件，英文注释请参考使用 grammarly 以及谷歌翻译。
```C
/**
* @brief The function will initialize a static event object.
*
* @note For the static event object, its memory space is allocated by the compiler during compiling,
* and shall placed on the read-write data segment or on the uninitialized data segment.
* By contrast, the rt_event_create() function will allocate memory space automatically
* and initialize the event.
*
* @see rt_event_create()
*
* @param event is a pointer to the event to initialize. It is assumed that storage for the event
* will be allocated in your application.
*
* @param name is a pointer to the name that given to the event.
*
* @param value is the initial value for the event.
* If want to share resources, you should initialize the value as the number of available resources.
* If want to signal the occurrence of an event, you should initialize the value as 0.
*
* @param flag is the event flag, which determines the queuing way of how multiple threads wait
* when the event is not available.
* The event flag can be ONE of the following values:
*
* RT_IPC_FLAG_PRIO The pending threads will queue in order of priority.
*
* RT_IPC_FLAG_FIFO The pending threads will queue in the first-in-first-out method
* (also known as first-come-first-served (FCFS) scheduling strategy).
*
* NOTE: RT_IPC_FLAG_FIFO is a non-real-time scheduling mode. It is strongly recommended to
* use RT_IPC_FLAG_PRIO to ensure the thread is real-time UNLESS your applications concern about
* the first-in-first-out principle, and you clearly understand that all threads involved in
* this event will become non-real-time threads.
*
* @return Return the operation status. When the return value is RT_EOK, the initialization is successful.
* If the return value is any other values, it represents the initialization failed.
*
* @warning This function can ONLY be called from threads.
*/
rt_err_t rt_event_init(rt_event_t event, const char *name, rt_uint8_t flag)
{
...
}
```
## 9.缩进及分行
缩进请采用 4 个空格的方式。如果没有什么特殊意义，请在 "{" 后进行分行，并在下一行都采用缩进的方式，例如：
```c
if (condition)
{
/* others */
}
```
唯一的例外是 switch 语句，switch-case 语句采用 case 语句与 switch 对齐的方式，例如：
```c
switch (value)
{
case value1:
break;
}
```
case 语句与前面的 switch 语句对齐，后续的语句则采用缩进的方式。分行上，如果没有什么特殊考虑，请**不要在代码中连续使用两个以上的空行**。
## 10.大括号与空格
从代码阅读角度，建议每个大括号单独占用一行，而不是跟在语句的后面，例如：
```c
if (condition)
{
/* others */
}
```
匹配的大括号单独占用一行，代码阅读起来就会有相应的层次而不会容易出现混淆的情况。空格建议在非函数方式的括号调用前留一个空格以和前面的进行区分，例如：
```c
if (x <= y)
{
/* others */
}
for (index = 0; index < MAX_NUMBER; index ++)
{
/* others */
}
```
建议在括号前留出一个空格(涉及的包括 if、for、while、switch 语句)，而运算表达式中，运算符与字符串间留一个空格。另外，不要在括号的表达式两侧留空格，例如：
```c
if ( x <= y )
{
/* other */
}
```
这样括号内两侧的空格是不允许的。
## 11.日志信息
代码中多使用ulog的方式来输出日志，例如：
```
#define DBG_TAG "Driver"
#define DBG_LVL DBG_INFO
#include <rtdbg.h>
LOG_D("this is a debug log.");
```
- 在 RT-Thread 中，普遍使用的日志输出方式是通过`LOG_D` 、`LOG_I` 、`LOG_W` 、`LOG_E`的方式来输出日志，同时它也可以通过DBG_TAG来区分日志类别，DBG_LVL控制日志输出的等级。
- 日志应该是以输出易懂易定位问题的方式。"天书式"的日志系统是糟糕的，不合理的，不应该出现在代码中。
- 禁止在头文件中重定义DBG_TAG，防止其他模块包含时DBG_TAG出现不可控。
- 严禁在timer或者中断打印大量日志，尽可能的避免或轻量化。
- 不建议使用rt_kprintf来作为日志输出方式，rt_kprintf一般作为终端命令行交互使用。
## 12.函数
在内核编程中，函数应该尽量精简，仅完成相对独立的简单功能。函数的实现不应该太长，函数实现太长，应该反思能够如何修改(或拆分)使得函数更为精简、易懂。
## 13.对象
RT-Thread 内核采用了 C 语言对象化技术，命名表现形式是：对象名结构体表示类定义、对象名 + 动词短语形式表示类方法，例如：
```c
struct rt_timer
{
struct rt_object parent;
/* other fields */
};
typedef struct rt_timer* rt_timer_t;
```
结构体定义 rt_timer 代表了 timer 对象的类定义；
```c
rt_timer_t rt_timer_create(const char* name,
void (*timeout)(void* parameter),
void* parameter,
rt_tick_t time, rt_uint8_t flag);
rt_err_t rt_timer_delete(rt_timer_t timer);
rt_err_t rt_timer_start(rt_timer_t timer);
rt_err_t rt_timer_stop(rt_timer_t timer);
```
rt_timer + 动词短语的形式表示能够应用于 timer 对象的方法。
在创建一个新的对象时，应该思考好，对象的内存操作处理：是否允许一个静态对象存在，或仅仅支持从堆中动态分配的对象。
## 14.格式化代码
格式化代码是指通过脚本自动整理你的代码，并使其符合 RT-Thread 的编码规范。本文提供以下两种自动格式化代码方法，可以自行选择或配合使用。
### 使用 astyle 格式化
用 astyle 自动格式化代码，参数如下：
--style=allman
--indent=spaces=4
--indent-preproc-block
--pad-oper
--pad-header
--unpad-paren
--suffix=none
--align-pointer=name
--lineend=linux
--convert-tabs
--verbose
能满足函数空格、缩进、函数语句等的规范。
### 使用 formatting 格式化
使用 [formatting](https://github.com/mysterywolf/formatting) 扫描文件来格式化代码：formatting 可以满足编码规则的基本要求，如：
- 将源文件编码统一为 UTF-8
- 将 TAB 键替换为 4 空格
- 将每行末尾多余的空格删除，并统一换行符为 '\n'

226
documentation/contribution_guide/coding_style_en.md Normal file
View file

@ -0,0 +1,226 @@
RT-Thread Coding Style
This is an developing instruction for RT-Thread developers. As open source
software, RT-Thread is created by the cooperation of different people. This
document is a guide for RT-Thread developers. Please obey it as you develop.
RT-Thread users should also get to know some conventions in the code through it
and thus easier to understand the implementations of RT-Thread.
1. Directory Naming
In normal conditions, please name directories in lowercase. Directories should
have descriptive names. For example, the port of a chip should be composed of
the name of the chip and the category of the chip. Directories under components/
should name what the component does.
2. File Naming
In normal conditions, please name files in lowercase. If the file is
referencing other places, it can have the original name. To avoid naming
collision, do not use general names or the names that are frequently used.
3. Header Files
To avoid include the same header file for multiple times, you need to define a
symbol like this:
#ifndef __FILE_H__
#define __FILE_H__
/* header file content */
#endif
The symbol should begin and end with "__" to avoid naming collision. The words
of the file name should be connected by "_". (This convention is called "snake case".)
4. Header File Comments
In every header file, there should be copyright information and Change Log
record like this:
/*
* Copyright (c) 2006-2020, RT-Thread Development Team
*
* SPDX-License-Identifier: Apache-2.0
*
* Change Logs:
* Date Author Notes
* 2006-03-18 Bernard the first version
* 2006-04-26 Bernard add semaphore APIs
*/
5. Structure Defines
Please name structures in lowercase and connect words with "_". For example:
struct rt_list_node
{
struct rt_list_node *next;
struct rt_list_node *prev;
};
Braces should have their own lines and the members should be indented.
The names of type defines such as structure types should be the structure name
plus "_t". For example:
typedef struct rt_list_node rt_list_t;
In order to be easily referenced, the types of objects in the kernel are pointers. For
example:
typedef struct rt_timer* rt_timer_t;
6. Macros
In RT-Thread, please use uppercase names for macro definitions. Words are
connected by "_". Like:
#define RT_TRUE 1
7. Function Naming and Declaration
Please name functions in lowercase. Separate words with "_". The API provided to
upper application should be declared in header files. If the function don't have
parameters, it should be declared as void:
rt_thread_t rt_thread_self(void);
8. Commenting
Please use English to comment. There shouldn't be many comments as the
comments should describe what the code does. It should describe complicated
algorithms, for example. Comments for statements should be placed before the
statements or to the right of them. Any other locations are invalid.
9. Indent
Please use TAB or 4 spaces to indent. It's preferred to use 4 spaces. If no
other special meanings, the indent should begin right after "{":
if (condition)
{
/* others */
}
The only one exception is switch. In case statements for switches, "case" should be
aligned with "switch":
switch (value)
{
case value1:
break;
}
"case" is aligned with "switch". The following code block should be indented.
10. Braces and Spaces
For ease of reading, it is advised that braces should occupy the whole line
instead of following other statements. Like:
if (condition)
{
/* others */
}
When matching braces have their own lines, the reader identifies the code
blocks easily.
There should be a space before parentheses when it's not a function call. For
example:
if (x <= y)
{
/* others */
}
for (index = 0; index < MAX_NUMBER; index ++)
{
/* others */
}
In expressions, there should be a space between most binary and ternary
operators and the strings. There should be no spaces around(inside) parentheses, like:
if ( x <= y )
{
/* other */
}
This is a bad practice.
11. trace, log Information
In RT-Thread, rt_kprintf is a commonly used logging routine. In RT-Thread
rt_kprintf is implemented as a polling, non-interrupting string output. It is
suitable in "instant" situations such as interrupt context. The polling method
would have influence to the timing sequence of the log output.
It is not recommended to use rt_kprintf frequently. Please be aware that frequen
use will make your code run slower.
Logging should be off by default and can be turned on by a switch (e.g. a
variable or a macro). When logging, it should be easy to understand and easy to
determine where the problem is.
12. Functions
Functions in kernel should be K.I.S.S. ("Keep it simple, stupid.") If the function
is too long, you should split it into smaller ones, with each of them simplified to
be easy to understand.
13. Objects
The kernel of RT-Thread uses object-oriented techniques in C. The naming convention
is: structure names are the object names, object names + verb phrases are the
method names of objects:
struct rt_timer
{
struct rt_object parent;
/* other fields */
};
typedef struct rt_timer* rt_timer_t;
The definition of structure rt_timer stands for the object definition of timer
object.
rt_timer_t rt_timer_create(const char* name,
void (*timeout)(void* parameter), void* parameter,
rt_tick_t time, rt_uint8_t flag);
rt_err_t rt_timer_delete(rt_timer_t timer);
rt_err_t rt_timer_start(rt_timer_t timer);
rt_err_t rt_timer_stop(rt_timer_t timer);
rt_timer + verb phrase stands for the method that could be used on a timer object.
When creating a new object, think twice on memory allocations: whether a static
object could be created or it could only created dynamically on the heap. Allocations
can be slower, but may be necessary in dynamic environments.
14. Use astyle to format the code automatically
parameters: --style=allman
--indent=spaces=4
--indent-preproc-block
--pad-oper
--pad-header
--unpad-paren
--suffix=none
--align-pointer=name
--lineend=linux
--convert-tabs
--verbose

171
documentation/contribution_guide/contribution_guide.md Normal file
View file

@ -0,0 +1,171 @@
# Contribution Guide
We sincerely thank you for your contribution, and welcome to submit the code through GitHub's fork and Pull Request processes.
First, explain the word Pull Request. Pull request means to send a request. The purpose of the developer initiating Pull Request is to request the repository maintainer to adopt the code submitted by the developer.
When you want to correct mistakes in other people's repositories, follow the following procedure:
- To fork someone else's repository is equivalent to copying someone else's information. Because you can't guarantee that your modification is correct and beneficial to the project, you can't modify it directly in someone else's repository, but first fork it into your own git repository.
- Clone code to your own PC local, create a new branch, modify bugs or add new features, and then launch pull request to the original repository, so that the original repository manager can see the changes you submitted.
- The original repository manager reviews this submission and, if correct, merge it into his own project. Merge means merging, merging the part of code you modified into the original repository to add code or replace the original code. So far, the whole Pull Request process is over.
## Coding Style
Refer to the `coding_style_en.txt` file in the rt_thread project documentation directory for the RT-Thread code programming style.
## Preparation
Install Git: You need to add Git's directory to the system environment variable.
## Contribution Process
Now take RT-Thread repository as an example to illustrate the process of contributing code:
### Fork
Fork the RT-Thread/rt-thread repository into your git repository.
![fork rt-thread repository](figures/cloneformgit.png)
### Clone
In your repository, copy the repository links after your fork:
![clone rt-thread from your repo](figures/cloneformgit2.png)
You can use the `git clone` command to copy the repository to your PC:
```
git clone [url]
```
![git clone](figures/git_clone.png)
### Create a New Branch
It is recommended that you create your own development branch based on the master branch, and use following commands to create a new branch:
```
git checkout -b YourBranchName
```
For example, create a branch named "dev": `git checkout -b dev`.
### Developing
Modify bugs and submit new functional code. For example, suppose the developer adds a USB driver:
![Add a USB driver](figures/add_usb_driver.png)
### Temporarily Store Modified Files
Add all changes to the temporary area:
```
git add .
```
If you only want to add some specified files to the temporary area, use other commands of `git add`.
### Commit
Submit this modification to the local repository:
```
git commit -m "Describe your submission here"
```
> Note: If there are multiple commits in the local development branch, in order to ensure that the RT-Thread repository commit is clean, please tidy up the local commits. More than five commits are not accepted by Pull Request.。
### Push to Your Remote Repository
Push the modified content to the branch of your remote repository. It is recommended that the branch name of the remote repository be consistent with the local branch name.Use the following command to push:
```
git push origin YourBranchName
```
### Create a Pull Request
Enter the RT-Thread repository under your Github account and click `New pull request -> Create pull request`. Make sure you choose the right branch.
![Create a Pull Request](figures/pull_request_step2.png)
Step 1: Fill in the title of this Pull Request
Step 2: Modify the description information of this Pull Request (modify it in `Write` and preview it with `Preview`):
- Modify PR Description: Replace the content in the red box below with the description of this pull request according to the requirements in the red box below.
- Check PR Options: Fill in [x] in the OK Options check box to confirm. Note that there are no spaces on both sides of [x].
![Modify PR Description and Check PR Options](figures/pr_description.png)
Step 3：Create pull request.
### Sign CLA
The first contribution to RT-Thread requires signing the *Contributor License Agreement*.
![Sign CLA](figures/cla.png)
Make sure that CLA shows successful signing and CI compilation, as shown in the following figure:
![CLA successful](figures/checkok.png)
Note: Do not submit commmit using a non-GitHub account, or commit using a different account, which can lead to CLA signing failure.
### Review Pull Request
Once the request is successful, the RT-Thread maintainer can see the code you submitted. The code will be reviewed and comments will be filled in on GitHub. Please check the PR status in time and update the code according to the comments.
### Merge Pull Request
If the Pull Request code is okay, the code will be merged into the RT-Thread repository. This time Pull Request succeeded.
So far, we have completed a code contribution process.
## Keep in Sync with RT-Thread Repository
The content of the RT-Thread GitHub repository is always updated. To develop based on the latest RT-Thread code, you need to update the local repository.
After clone, the local master branch content is consistent with the master branch content of the RT-Thread repository. But when the RT-Thread repository is updated, your local code is different from the RT-Thread code.
The local master is synchronized with the RT-Thread repository of your own GitHub account. If there is no content modification for the master branch (please create a new branch for development), then you can keep the local code synchronized with the RT-Thread repository according to the following steps:
- To view the existing remote repository, there is usually only one default origin, which is your own remote repository:
```c
$ git remote -v
origin https://github.com/YOUR_USERNAME/YOUR_FORK.git (fetch)
origin https://github.com/YOUR_USERNAME/YOUR_FORK.git (push)
```
* Add the RT-Thread remote repository and name it `rtt`, or you can customize the name by yourself:
```c
$ git remote add rtt https://github.com/RT-Thread/rt-thread.git
```
* View all remote repositories tracked locally:
```c
$ git remote -v
origin https://github.com/YOUR_USERNAME/YOUR_FORK.git (fetch)
origin https://github.com/YOUR_USERNAME/YOUR_FORK.git (push)
rtt https://github.com/RT-Thread/rt-thread.git (fetch)
rtt https://github.com/RT-Thread/rt-thread.git (push)
```
* Pull the code from the master branch of RT-Thread remote repository and merge it into the local master branch:
```c
git pull rtt master
```
## Reference
* Refer to the [*GitHub - Contributing to a Project*](https://git-scm.com/book/en/v2/GitHub-Contributing-to-a-Project) section of the official Git document for details.

BIN
documentation/contribution_guide/figures/add_usb_driver.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 9.1 KiB

BIN
documentation/contribution_guide/figures/branch.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 13 KiB

BIN
documentation/contribution_guide/figures/checkok.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 20 KiB

BIN
documentation/contribution_guide/figures/cla.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 18 KiB

BIN
documentation/contribution_guide/figures/cloneformgit.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 57 KiB

BIN
documentation/contribution_guide/figures/cloneformgit2.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 80 KiB

BIN
documentation/contribution_guide/figures/git_clone.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 8.3 KiB

BIN
documentation/contribution_guide/figures/pr_description.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 138 KiB

BIN
documentation/contribution_guide/figures/pull_request_step2.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 81 KiB

263
documentation/device/adc/adc.md Normal file
View file

@ -0,0 +1,263 @@
# ADC Device
## An Introduction to ADC
An ADC (analog-to-digital converter) is a hardware device that converts continuously changing analog signals to discrete digital signals. Usually, these analog signals include temperature, pressure, sound, video and many other types of signals. Converting them is important, as digital signals are easier to store, process, and transmit. This conversion can be achieved by using an ADC device which is commonly integrated in various platforms. Historically, ADCs were first used to convert received wireless signals to digital signals, for example, television signals, or signals from long-short broadcast stations.
### Conversion Process
As shown in the figure below, the analog-to-digital conversion generally involves steps of sampling, holding, quantifying, and encoding. In actual circuits, some processes are combined, such as sampling and holding, while quantization and encoding are implemented simultaneously in the conversion process.
![ADC Conversion Process](figures/adc-p.png)
Sampling is the conversion of analog signals that changes continuously over time into time-discrete analog signals. It takes a certain amount of time for the analog signals obtained by sampling to be converted into digital signals. In order to provide a stable value for the subsequent quantization coding process, it is required to keep the sampling analog signals for a period of time after the sampling circuit.
The process of converting a numerically continuous analog quantity into a digital quantity is called quantization. Digital signals are discrete numerically. The output voltage of the sample-and-hold circuit also needs to be naturalized to a corresponding discrete level in a similar way, and any digital quantity can only be an integer multiple of a certain minimum quantity unit. The quantized value also requires the encoding process, which is the digital output of the A/D converter.
### Resolution
Resolution is represented as binary (or decimal) numbers. Generally, it comes in 8 bits, 10 bits, 12 bits, 16 bits, etc. A larger resolution, in bits, means more accuracy in the conversion of analog to digital signals.
### Precision
Precision is the maximum error value between analog signals and real ADC device numerical points’ values.An ADC with a high resolution might have a low precision, meaning that factors like noise can affect the numerical ADC reading more than small changes in the input signal.
### Conversion Rate
The conversion rate is the reciprocal of time taken for an ADC device to complete conversion from an analog to a digital signal. For example, an ADC device with a conversion rate of 1MHz means that the ADC conversion time is 1 microsecond.
## Access ADC Device
The application accesses the ADC hardware through the ADC device management interface provided by RT-Thread. The relevant interfaces are as follows:
| **Function** | Description |
| --------------- | ------------------ |
| rt_device_find() | Find device handles based on ADC device name |
| rt_adc_enable() | Enable ADC devices |
| rt_adc_read() | Read ADC device data |
| rt_adc_disable() | Close the ADC device |
### Find ADC Devices
The application gets the device handler based on the ADC device name to operate the ADC device. Following is the interface function to find the devices:
```c
rt_device_t rt_device_find(const char* name);
```
| **Parameter** | Description |
| -------- | ---------------------------------- |
| name | The name of the ADC device |
| **Return** | —— |
| Device handle | Finding the corresponding device will return to the corresponding device handle |
| RT_NULL | No device found
|
In a nutshell, the names of the ADC devices are registered as adc0, adc1, and so on. What follows is an example on how to use it
```c
#define ADC_DEV_NAME "adc1" /* ADC device name */
rt_adc_device_t adc_dev; /* ADC device handle */
/* find the device */
adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
```
### Enable ADC Channel
It is required to enable the ADC device with the following interface function before reading and operating the ADC device.
```c
rt_err_t rt_adc_enable(rt_adc_device_t dev, rt_uint32_t channel);
```
| Parameter | Description |
| ---------- | ------------------------------- |
| dev | ADC device handle |
| channel | ADC channel |
| **Return** | —— |
| RT_EOK | Succeed |
| -RT_ENOSYS | Failed, the device operation method is empty |
| Other error code | Failed |
An usage example is as follows:
```c
#define ADC_DEV_NAME "adc1" /* ADC device name */
#define ADC_DEV_CHANNEL 5 /* ADC channel */
rt_adc_device_t adc_dev; /* ADC device handle */
/* find the device */
adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
/* enable the device */
rt_adc_enable(adc_dev, ADC_DEV_CHANNEL);
```
### Read ADC Channel Sample Values
Reading the ADC channel sample values can be done by the following function:
```c
rt_uint32_t rt_adc_read(rt_adc_device_t dev, rt_uint32_t channel);
```
| Parameter | Description |
| ---------- | ----------------- |
| dev | ADC device handle |
| channel | ADC channel |
| **Return** | —— |
| Read values | |
An example of using the ADC sampled voltage value is as follows:
```c
#define ADC_DEV_NAME "adc1" /* ADC device name */
#define ADC_DEV_CHANNEL 5 /* ADC channel */
#define REFER_VOLTAGE 330 /* Reference voltage 3.3V, data accuracy multiplied by 100 and reserve 2 decimal places*/
#define CONVERT_BITS (1 << 12) /* The number of conversion bits is 12 */
rt_adc_device_t adc_dev; /* ADC device handle */
rt_uint32_t value；
/* find the device */
adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
/* enable the device */
rt_adc_enable(adc_dev, ADC_DEV_CHANNEL);
/* Read sampling values */
value = rt_adc_read(adc_dev, ADC_DEV_CHANNEL);
/* Convert to the corresponding voltage value */
vol = value * REFER_VOLTAGE / CONVERT_BITS;
rt_kprintf("the voltage is :%d.%02d \n", vol / 100, vol % 100);
```
The calculation formula of the actual voltage value is: `sampling value * reference voltage/(1 << resolution digit)`. In the above example, variable *vol* was enlarged 100 times, so finally the integer part of voltage is obtained through *vol / 100*, and the decimal part of voltage is obtained through *vol % 100*.
### Disabling the ADC Channel
An ADC channel can be disabled through the following function:
```c
rt_err_t rt_adc_disable(rt_adc_device_t dev, rt_uint32_t channel);
```
| **Parameter** | **Description** |
| ---------- | ------------------------------- |
| dev | ADC device handle |
| channel | ADC channel |
| **Return** | —— |
| RT_EOK | Succeed |
| -RT_ENOSYS | Failed, the device operation method is empty |
| Other error code | Failed |
An example:
```c
#define ADC_DEV_NAME "adc1" /* ADC device name */
#define ADC_DEV_CHANNEL 5 /* ADC channel */
rt_adc_device_t adc_dev; /* ADC device handle */
rt_uint32_t value；
/* find the device */
adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
/* enable the device */
rt_adc_enable(adc_dev, ADC_DEV_CHANNEL);
/* read sampling values */
value = rt_adc_read(adc_dev, ADC_DEV_CHANNEL);
/* convert to the corresponding voltage value */
vol = value * REFER_VOLTAGE / CONVERT_BITS;
rt_kprintf("the voltage is :%d.%02d \n", vol / 100, vol % 100);
/* close the channel */
rt_adc_disable(adc_dev, ADC_DEV_CHANNEL);
```
### FinSH Command
To find out the registered device, you can use the command adc probe followed by the registered ADC device name as following,
```c
msh >adc probe adc1
probe adc1 success
```
A channel of the enabled device can use the command `adc enable` followed by the channel number.
```c
msh >adc enable 5
adc1 channel 5 enables success
```
To read data from a channel of an ADC device, you can use the command `adc read` followed by the channel number.
```c
msh >adc read 5
adc1 channel 5 read value is 0x00000FFF
msh >
```
To close a channel of an ADC device, you can use the command `adc disable` followed by the channel number.
```c
msh >adc disable 5
adc1 channel 5 disable success
msh >
```
## ADC Device Usage Example
The specific usage of the ADC device can refer to the following sample code. The main steps of the sample code are as follows:
1. First find the device handle based on the ADC device name “adc1”.
2. After the device is enabled, read the sample value of the corresponding channel 5 of the adc1 device, and then calculate the actual voltage value with the resolution of 12 bits and the reference voltage of 3.3V.
3. Finally close the corresponding channel of the ADC device.
Running result: Print the raw and converted data which actually read , and print the calculated actual voltage value.
```c
/*
* Program Listing： ADC Device Usage Routines
* The routine exports the adc_sample command to the control terminal
* adc_sample Command call format: adc_sample
* Program function: The voltage value is sampled by the ADC device and converted to a numerical value.
* The sample code reference voltage is 3.3V and the number of conversion bits is 12 bits.
*/
#include <rtthread.h>
#include <rtdevice.h>
#define ADC_DEV_NAME "adc1" /* ADC device name */
#define ADC_DEV_CHANNEL 5 /* ADC channel */
#define REFER_VOLTAGE 330 /* Reference voltage 3.3V, data accuracy multiplied by 100 and reserve 2 decimal places*/
#define CONVERT_BITS (1 << 12) /* The number of conversion bits is 12 */
static int adc_vol_sample(int argc, char *argv[])
{
rt_adc_device_t adc_dev;
rt_uint32_t value, vol;
rt_err_t ret = RT_EOK;
/* find the device */
adc_dev = (rt_adc_device_t)rt_device_find(ADC_DEV_NAME);
if (adc_dev == RT_NULL)
{
rt_kprintf("adc sample run failed! can't find %s device!\n", ADC_DEV_NAME);
return -RT_ERROR;
}
/* enable the device */
ret = rt_adc_enable(adc_dev, ADC_DEV_CHANNEL);
/* read sampling values */
value = rt_adc_read(adc_dev, ADC_DEV_CHANNEL);
rt_kprintf("the value is :%d \n", value);
/* convert to the corresponding voltage value */
vol = value * REFER_VOLTAGE / CONVERT_BITS;
rt_kprintf("the voltage is :%d.%02d \n", vol / 100, vol % 100);
/* close the channel */
ret = rt_adc_disable(adc_dev, ADC_DEV_CHANNEL);
return ret;
}
/* export to the msh command list */
MSH_CMD_EXPORT(adc_vol_sample, adc voltage convert sample);
```

BIN
documentation/device/adc/figures/adc-p.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 31 KiB

486
documentation/device/device.md Normal file
View file

@ -0,0 +1,486 @@
# I/O Device Framework
Most embedded systems include some I/O (Input/Output) devices, data displays on instruments, serial communication on industrial devices, Flash or SD cards for saving data on data acquisition devices,as well as Ethernet interfaces for network devices, are examples of I/O devices that are commonly seen in embedded systems.
This chapter describes how RT-Thread manages different I/O devices.
## I/O Device Introduction
### I/O Device Framework
RT-Thread provides a set of I/O device framework, as shown in the following figure. It is located between the hardware and the application. It is divided into three layers. From top to bottom, they are I/O device management layer, device driver framework layer, and device driver layer.
![I/O Device Framework](figures/io-dev.png)
The application obtains the correct device driver through the I/O device management interface, and then uses this device driver to perform data (or control) interaction with the bottom I/O hardware device.
The I/O device management layer implements the encapsulation of device drivers. The application accesses the bottom devices through the standard interface provided by the I/O device layer. The upgrade and replacement of the device driver will not affect the upper layer application. In this way, the hardware-related code of the device can exist independently of the application, and both parties only need to pay attention to the respective function implementation, thereby reducing the coupling and complexity of the code and improving the reliability of the system.
The device driver framework layer is an abstraction of the same kind of hardware device driver. The same part of the same hardware device driver of different manufacturers is extracted, and the different parts are left out of interface, implemented by the driver.
The device driver layer is a set of programs that drive the hardware devices to work, enabling access to hardware devices. It is responsible for creating and registering I/O devices. For devices with simple operation logic, you can register devices directly into the I/O Device Manager without going through the device driver framework layer. The sequence diagram is as shown below. There are mainly two points:
* The device driver creates a device instance with hardware access capabilities based on the device model definition and registers the device with the `rt_device_register()` interface in the I/O Device Manager.
* The application finds the device through the`rt_device_find()` interface and then uses the I/O device management interface to access the hardware.
![Simple I/O Device Using Sequence Diagram](figures/io-call.png)
For other devices, such as watchdog, the created device instance will be registered to the corresponding device driver framework, and then the device driver framework will register with the I/O device manager. The main points are as follows:
* The watchdog device driver creates a watchdog device instance with hardware access capability based on the watchdog device model definition and registers the watchdog device through the `rt_hw_watchdog_register()` interface into the watchdog device driver framework.
* The watchdog device driver framework registers the watchdog device to the I/O Device Manager via the `rt_device_register()` interface.
* The application accesses the watchdog device hardware through the I/O device management interface.
Usage of Watchdog device:
![Watchdog Device Use Sequence Diagram](figures/wtd-uml.png)
### I/O Device Model
The device model of RT-Thread is based on the kernel object model, which is considered a kind of objects and is included in the scope of the object manager. Each device object is derived from the base object. Each concrete device can inherit the properties of its parent class object and derive its own properties. The following figure is a schematic diagram of the inheritance and derivation relationship of device object.
![Device Inheritance Diagram](figures/io-parent.png)
The specific definitions of device objects are as follows:
```c
struct rt_device
{
struct rt_object parent; /* kernel object base class */
enum rt_device_class_type type; /* device type */
rt_uint16_t flag; /* device parameter */
rt_uint16_t open_flag; /* device open flag */
rt_uint8_t ref_count; /* number of times the device was cited */
rt_uint8_t device_id; /* device ID,0 - 255 */
/* data transceiving callback function */
rt_err_t (*rx_indicate)(rt_device_t dev, rt_size_t size);
rt_err_t (*tx_complete)(rt_device_t dev, void *buffer);
const struct rt_device_ops *ops; /* device operate methods */
/* device's private data */
void *user_data;
};
typedef struct rt_device *rt_device_t;
```
### I/O Device Type
RT-Thread supports multiple I/O device types, the main device types are as follows:
```c
RT_Device_Class_Char /* character device */
RT_Device_Class_Block /* block device */
RT_Device_Class_NetIf /* network interface device */
RT_Device_Class_MTD /* memory device */
RT_Device_Class_RTC /* RTC device */
RT_Device_Class_Sound /* sound device */
RT_Device_Class_Graphic /* graphic device */
RT_Device_Class_I2CBUS /* I2C bus device */
RT_Device_Class_USBDevice /* USB device */
RT_Device_Class_USBHost /* USB host device */
RT_Device_Class_SPIBUS /* SPI bus device */
RT_Device_Class_SPIDevice /* SPI device */
RT_Device_Class_SDIO /* SDIO device */
RT_Device_Class_Miscellaneous /* miscellaneous devices */
```
Character devices and block devices are commonly used device types, and their classification is based on the transmission processing between device data and the system. Character mode devices allow for unstructured data transfers, that is, data usually transfers in the form of serial, one byte at a time. Character devices are usually simple devices such as serial ports and buttons.
A block device transfers one data block at a time, for example 512 bytes data at a time. This data block is enforced by the hardware. Data blocks may use some type of data interface or some mandatory transport protocol, otherwise an error may occur. Therefore, sometimes the block device driver must perform additional work on read or write operations, as shown in the following figure:
![Block Device](figures/block-dev.png)
When the system serves a write operation with a large amount of data, the device driver must first divide the data into multiple packets, each with the data size specified by the device. In the actual process, the last part of the data size may be smaller than the normal device block size. Each block in the above figure is written to the device using a separate write request, and the first three are directly written. However, the last data block size is smaller than the device block size, and the device driver must process the last data block differently than the first 3 blocks. Normally, the device driver needs to first perform a read operation of the corresponding device block, then overwrite the write data onto the read data, and then write the "composited" data block back to the device as a whole block. . For example, for block 4 in the above figure, the driver needs to read out the device block corresponding to block 4, and then overwrite the data to be written to the data read from the device block, and merge them into a new block. Finally write back to the block device.
## Create and Register I/O Device
The driver layer is responsible for creating device instances and registering them in the I/O Device Manager. You can create device instances in a statically declared manner or dynamically create them with the following interfaces:
```c
rt_device_t rt_device_create(int type, int attach_size);
```
|**Parameters** |**Description** |
|-------------|-------------------------------------|
| type | device type, the device type values listed in "I/O Device Type" section can be used here |
| attach_size | user data size |
|**Return** | -- |
| Device Handle | Create successfully |
| RT_NULL | Creation failed, dynamic memory allocation failed |
When this interface is called, the system allocates a device control block from the dynamic heap memory, the size of which is the sum of `struct rt_device` and `attach_size`, and the type of the device is set by the parameter type. After the device is created, implementing its access to the hardware is needed.
```c
struct rt_device_ops
{
/* common device interface */
rt_err_t (*init) (rt_device_t dev);
rt_err_t (*open) (rt_device_t dev, rt_uint16_t oflag);
rt_err_t (*close) (rt_device_t dev);
rt_ssize_t (*read) (rt_device_t dev, rt_off_t pos, void *buffer, rt_size_t size);
rt_ssize_t (*write) (rt_device_t dev, rt_off_t pos, const void *buffer, rt_size_t size);
rt_err_t (*control)(rt_device_t dev, int cmd, void *args);
};
```
A description of each method of operation is shown in the following table:
|**Method Name**|**Method Description** |
|----|-----------------------|
| init | Initialize the device. After the device is initialized, the flag of the device control block is set to the active state(RT_DEVICE_FLAG_ACTIVATED). If the flag in the device control block has been set to the active state, then the initialization interface will be returned immediately when running again, and will not be re-initialized. |
| open | Open the device. Some devices are not started when the system is started, or the device needs to send and receive data. However, if the upper application is not ready, the device should not be enabled by default and start receiving data. Therefore, it is recommended to enable the device when calling the open interface when writing the bottom driver. |
| close | Close the device. When the device is open, the device control block maintains an open count, the count will add 1 when the device is opended, and the count will subtract 1 when the device is closed, and a real shutdown operation is operated when the counter turns to 0. |
| read | Read data from the device. The parameter pos is the offset of the read data, but some devices do not necessarily need to specify the offset, such as serial devices, the device driver should ignore this parameter. But for block devices, pos and size are measured in the block size of the block device. For example, the block size of the block device is 512 byte, and in the parameter pos = 10, size = 2, then the driver should return the 10th block in the device (starting from the 0th block) for a total of 2 blocks of data. The type returned by this interface is rt_size_t, which is the number of bytes read or the number of blocks. Normally, the value of size in the parameter should be returned. If it returns zero, set the corresponding errno value. |
| write | Write data to the device. The parameter pos is the offset of the write data. Similar to read operations, for block devices, pos and size are measured in the block size of the block device. The type returned by this interface is rt_size_t, which is the number of bytes or blocks of data actually written. Normally, the value of size in the parameter should be returned. If it returns zero, set the corresponding errno value. |
| control | Control the device according to the cmd command. Commands are often implemented by the bottom device drivers. For example, the parameter RT_DEVICE_CTRL_BLK_GETGEOME means to get the size information of the block device. |
When a dynamically created device is no longer needed, it can be destroyed using the following function:
```c
void rt_device_destroy(rt_device_t device);
```
|**Parameters**|**Description**|
|----------|----------|
| device | device handle |
After the device is created, it needs to be registered to the I/O Device Manager for the application to access. The functions for registering the device are as follows:
```c
rt_err_t rt_device_register(rt_device_t dev, const char* name, rt_uint8_t flags);
```
|**Parameters** |**Description** |
|------------|-----------------------|
| dev | device handle |
| name | device name, the maximum length of the device name is specified by the macro RT_NAME_MAX defined in rtconfig.h, and the extra part is automatically truncated |
| flags | device mode flag |
|**Return** | -- |
| RT_EOK | registration success |
| -RT_ERROR | registration failed, dev is empty or name already exists |
>It should be avoided to repeatedly register registered devices and to register devices with the same name.
flags parameters support the following parameters (multiple parameters can be supported in OR logic):
```c
#define RT_DEVICE_FLAG_RDONLY 0x001 /* read only */
#define RT_DEVICE_FLAG_WRONLY 0x002 /* write only */
#define RT_DEVICE_FLAG_RDWR 0x003 /* read and write */
#define RT_DEVICE_FLAG_REMOVABLE 0x004 /* can be removed */
#define RT_DEVICE_FLAG_STANDALONE 0x008 /* stand alone */
#define RT_DEVICE_FLAG_SUSPENDED 0x020 /* suspended */
#define RT_DEVICE_FLAG_STREAM 0x040 /* stream mode */
#define RT_DEVICE_FLAG_INT_RX 0x100 /* interrupt reception */
#define RT_DEVICE_FLAG_DMA_RX 0x200 /* DMA reception */
#define RT_DEVICE_FLAG_INT_TX 0x400 /* interrupt sending */
#define RT_DEVICE_FLAG_DMA_TX 0x800 /* DMA sending */
```
Device Stream Mode The RT_DEVICE_FLAG_STREAM parameter is used to output a character string to the serial terminal: when the output character is `\n` , it automatically fills in a `\r` to make a branch.
Successfully registered devices can use the `list_device` command on the FinSH command line to view all device information in the system, including the device name, device type, and number of times the device is opened:
```c
msh />list_device
device type ref count
-------- -------------------- ----------
e0 Network Interface 0
sd0 Block Device 1
rtc RTC 0
uart1 Character Device 0
uart0 Character Device 2
msh />
```
When the device is logged off, the device will be removed from the device manager and the device will no longer be found through the device. Logging out of the device does not release the memory occupied by the device control block. The function to log off of the device is as follows:
```c
rt_err_t rt_device_unregister(rt_device_t dev);
```
|**Parameters**|**Description**|
|----------|----------|
| dev | device handle |
|**Return**| -- |
| RT_EOK | successful |
The following code is an example of registering a watchdog device. After calling the `rt_hw_watchdog_register()` interface, the device is registered to the I/O Device Manager via the `rt_device_register()` interface.
```c
const static struct rt_device_ops wdt_ops =
{
rt_watchdog_init,
rt_watchdog_open,
rt_watchdog_close,
RT_NULL,
RT_NULL,
rt_watchdog_control,
};
rt_err_t rt_hw_watchdog_register(struct rt_watchdog_device *wtd,
const char *name,
rt_uint32_t flag,
void *data)
{
struct rt_device *device;
RT_ASSERT(wtd != RT_NULL);
device = &(wtd->parent);
device->type = RT_Device_Class_Miscellaneous;
device->rx_indicate = RT_NULL;
device->tx_complete = RT_NULL;
device->ops = &wdt_ops;
device->user_data = data;
/* register a character device */
return rt_device_register(device, name, flag);
}
```
## Access I/O Devices
The application accesses the hardware device through the I/O device management interface, which is accessible to the application when the device driver is implemented. The mapping relationship between the I/O device management interface and the operations on the I/O device is as follows:
![Mapping between the I/O Device Management Interface and the Operations on the I/O Device](figures/io-fun-call.png)
### Find Device
The application obtains the device handle based on the device name, which in turn allows the device to operate. To find device, use function below:
```c
rt_device_t rt_device_find(const char* name);
```
|**Parameters**|**Description** |
|----------|------------------------------------|
| name | device name |
|**Return**| -- |
| device handle | finding the corresponding device will return the corresponding device handle |
| RT_NULL | no corresponding device object found |
### Initialize Device
Once the device handle is obtained, the application can initialize the device using the following functions:
```c
rt_err_t rt_device_init(rt_device_t dev);
```
|**Parameters**|**Description** |
|----------|----------------|
| dev | device handle |
|**Return**| -- |
| RT_EOK | device initialization succeeded |
| Error Code | device initialization failed |
>When a device has been successfully initialized, calling this interface will not repeat initialization.
### Open and Close Device
Through the device handle, the application can open and close the device. When the device is opened, it will detect whether the device has been initialized. If it is not initialized, it will call the initialization interface to initialize the device by default. Open the device with the following function:
```c
rt_err_t rt_device_open(rt_device_t dev, rt_uint16_t oflags);
```
|**Parameters** |**Description** |
|------------|-----------------------------|
| dev | device handle |
| oflags | open device in oflag mode |
|**Return** | -- |
| RT_EOK | device successfully turned on |
|-RT_EBUSY | device will not allow being repeated opened if the RT_DEVICE_FLAG_STANDALONE parameter is included in the parameters specified when the device is registered. |
| Other Error Code | device failed to be turned on |
oflags supports the following parameters:
```c
#define RT_DEVICE_OFLAG_CLOSE 0x000 /* device was already closed(internal use)*/
#define RT_DEVICE_OFLAG_RDONLY 0x001 /* open the device in read-only mode */
#define RT_DEVICE_OFLAG_WRONLY 0x002 /* open the device in write-only mode */
#define RT_DEVICE_OFLAG_RDWR 0x003 /* open the device in read-and_write mode */
#define RT_DEVICE_OFLAG_OPEN 0x008 /* device was already closed(internal use) */
#define RT_DEVICE_FLAG_STREAM 0x040 /* open the device in stream mode */
#define RT_DEVICE_FLAG_INT_RX 0x100 /* open the device in interrupt reception mode */
#define RT_DEVICE_FLAG_DMA_RX 0x200 /* open the device in DMA mode */
#define RT_DEVICE_FLAG_INT_TX 0x400 /* open the device in interrupt sending mode */
#define RT_DEVICE_FLAG_DMA_TX 0x800 /* open the device in DMA mode */
```
>If the upper application needs to set the device's receive callback function, it must open the device as RT_DEVICE_FLAG_INT_RX or RT_DEVICE_FLAG_DMA_RX, otherwise the callback function will not be called.
After the application opens the device to complete reading and writing, if no further operations are needed, you can close the device using the following functions:
```c
rt_err_t rt_device_close(rt_device_t dev);
```
|**Parameters** |**Description** |
|------------|------------------------------------|
| dev | device handle |
|**Return** | -- |
| RT_EOK | device successfully closed |
| \-RT_ERROR | device has been completely closed and cannot be closed repeatedly |
| Other Error Code | failed to close device |
>Device interfaces `rt_device_open()` and `rt_device_close()` need to used in pairs. Open a device requires close the device, so that the device will be completely closed, otherwise the device will remain on.
### Control Device
By commanding the control word, the application can also control the device with the following function:
```c
rt_err_t rt_device_control(rt_device_t dev, rt_uint8_t cmd, void* arg);
```
|**Parameters** |**Description** |
|-------------|--------------------------------------------|
| dev | device handle |
| cmd | command control word, this parameter is usually related to the device driver |
| arg | controlled parameter |
|**Return** | -- |
| RT_EOK | function executed successfully |
| -RT_ENOSYS | execution failed, dev is empty |
| Other Error Code | execution failed |
The generic device command for the parameter `cmd` can be defined as follows:
```c
#define RT_DEVICE_CTRL_RESUME 0x01 /* resume device */
#define RT_DEVICE_CTRL_SUSPEND 0x02 /* suspend device */
#define RT_DEVICE_CTRL_CONFIG 0x03 /* configure device */
#define RT_DEVICE_CTRL_SET_INT 0x10 /* set interrupt */
#define RT_DEVICE_CTRL_CLR_INT 0x11 /* clear interrupt */
#define RT_DEVICE_CTRL_GET_INT 0x12 /* obtain interrupt status */
```
### Read and Write Device
Application can read data from the device by the following function:
```c
rt_size_t rt_device_read(rt_device_t dev, rt_off_t pos,void* buffer, rt_size_t size);
```
|**Parameters** |**Description** |
|--------------------|--------------------------------|
| dev | device handle |
| pos | read data offset |
| buffer | memory buffer pointer, the data read will be saved in the buffer |
| size | size of the data read |
|**Return** | -- |
| Actual Size of the Data Read | If it is a character device, the return size is in bytes. If it is a block device, the returned size is in block units. |
| 0 | need to read the current thread's errno to determine the error status |
Calling this function will read the data from the dev device and store it in the buffer. The maximum length of this buffer is *size*, and *pos* has different meanings depending on the device class.
Writing data to the device can be done by the following function:
```c
rt_size_t rt_device_write(rt_device_t dev, rt_off_t pos,const void* buffer, rt_size_t size);
```
|**Parameters** |**Description** |
|--------------------|--------------------------------|
| dev | device handle |
| pos | write data offset |
| buffer | memory buffer pointer, placing the data to be written in |
| size | size of the written data |
|**Return** | -- |
| Actual Size of the Data Written | If it is a character device, the return size is in bytes. If it is a block device, the returned size is in block units. |
| 0 | need to read the current thread's errno to determine the error status |
Calling this function will write the data in the buffer to the *dev* device . The maximum length of the written data is *size*, and *pos* has different meanings depending on the device class.
### Data Transceiving and Call-back
When the hardware device receives the data, the following function can be used to call back another function to set the data receiving indication to notify the upper application thread that the data arrives:
```c
rt_err_t rt_device_set_rx_indicate(rt_device_t dev, rt_err_t (*rx_ind)(rt_device_t dev,rt_size_t size));
```
|**Parameters**|**Description** |
|----------|--------------|
| dev | device handle |
| rx_ind | callback function pointer |
|**Return**| -- |
| RT_EOK | set successfully |
The callback of this function will be provided by the user. When the hardware device receives the data, it will perform the callback function and pass the received data length to the upper layer application in the *size* parameter. The upper application thread should read the data from the device as soon as it receives the indication.
When the application calls `rt_device_write()` to write data, if the bottom hardware can support automatic sending, the upper application can set a callback function. This callback function is called after the bottom hardware data has been sent (for example, when the DMA transfer is complete or the FIFO has been written to complete, triggered interrupt). Use the following function to set the device with a send completion indication. The function parameters and return values are as follows:
```c
rt_err_t rt_device_set_tx_complete(rt_device_t dev, rt_err_t (*tx_done)(rt_device_t dev,void *buffer));
```
|**Parameters**|**Description** |
|----------|--------------|
| dev | device handle |
| tx_done | callback function pointer |
|**Return**| -- |
| RT_EOK | set successfully |
When this function is called, the callback function is provided by the user. When the hardware device sends the data, the driver calls back the function and passes the sent data block address buffer as a parameter to the upper application. When the upper layer application (thread) receives the indication, it will release the buffer memory block or use it as the buffer for the next write data according to the condition of sending the buffer.
### Access Device Sample
The following code is an example of accessing a device. First, find the watchdog device through the `rt_device_find()` port, obtain the device handle, then initialize the device through the `rt_device_init()` port, and set the watchdog device timeout through the `rt_device_control()`port.
```c
#include <rtthread.h>
#include <rtdevice.h>
#define IWDG_DEVICE_NAME "iwg"
static rt_device_t wdg_dev;
static void idle_hook(void)
{
/* feed the dog in the callback function of the idle thread */
rt_device_control(wdg_dev, RT_DEVICE_CTRL_WDT_KEEPALIVE, NULL);
rt_kprintf("feed the dog!\n ");
}
int main(void)
{
rt_err_t res = RT_EOK;
rt_uint32_t timeout = 1000; /* timeout */
/* find the watchdog device based on the device name, and obtain the device handle */
wdg_dev = rt_device_find(IWDG_DEVICE_NAME);
if (!wdg_dev)
{
rt_kprintf("find %s failed!\n", IWDG_DEVICE_NAME);
return -RT_ERROR;
}
/* initialize device */
res = rt_device_init(wdg_dev);
if (res != RT_EOK)
{
rt_kprintf("initialize %s failed!\n", IWDG_DEVICE_NAME);
return res;
}
/* set watchdog timeout */
res = rt_device_control(wdg_dev, RT_DEVICE_CTRL_WDT_SET_TIMEOUT, &timeout);
if (res != RT_EOK)
{
rt_kprintf("set %s timeout failed!\n", IWDG_DEVICE_NAME);
return res;
}
/* set idle thread callback function */
rt_thread_idle_sethook(idle_hook);
return res;
}
```

BIN
documentation/device/figures/block-dev.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 14 KiB

BIN
documentation/device/figures/io-call.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 17 KiB

BIN
documentation/device/figures/io-dev.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 20 KiB

BIN
documentation/device/figures/io-fun-call.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 16 KiB

BIN
documentation/device/figures/io-parent.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 20 KiB

BIN
documentation/device/figures/wtd-uml.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 46 KiB

401
documentation/device/hwtimer/hwtimer.md Normal file
View file

@ -0,0 +1,401 @@
# HWTIMER Device
## Introduction to the Timer
Hardware timers generally have two modes of operation, timer mode and counter mode. No matter which mode is operated, it works by counting the pulse signal counted by the internal counter module. Here are some important concepts of timers.
**Timer mode**: Counts the internal pulse. Timers are often used as timing clocks for timing detection, timing response, and timing control.
**Counter mode**: The counter can count up or down. The maximum count value of a 16-bit counter is 65535, and the maximum value of a 32-bit counter is 4 294 967 295.
**Counting frequency**：Since the input frequency is usually fixed, the time it takes for the counter to reach its desired count number can be calculated from just the given frequency - `time = count value / count frequency`. For example, if the counting frequency is 1 MHz, the counter counts once every 1 / 1000000 seconds. That is, every 1 microsecond, the counter is incremented by one (or subtracted by one), at this time, the maximum timing capability of the 16-bit counter is 65535 microseconds, or 65.535 milliseconds.
## Access Hardware Timer Device
The application accesses the hardware timer device through the I/O device management interface provided by RT-Thread. The related interfaces are as follows:
| **Function** | **Description** |
| -------------------- | ---------------------------------- |
| rt_device_find() | to look up the timer device |
| rt_device_open() | to open the timer device in read-write mode |
| rt_device_set_rx_indicate() | to set the timeout callback function |
| rt_device_control() | to control the timer device, you can set the timing mode (single time /cycle),counting frequency, or stop the timer |
| rt_device_write() | to set the timeout value of the timer. The timer then starts |
| rt_device_read() | to get the current value of the timer |
| rt_device_close() | to turn off the timer device. |
### Find Timer Device
The application obtains the device handle based on the hardware timer device name, and thus can operate the hardware timer device. The device function is as follows:
```c
rt_device_t rt_device_find(const char* name);
```
| Parameter | **Description** |
| -------- | ---------------------------------- |
| name | hardware timer device name |
| **return** | —— |
| timer device handle | will return to the corresponding device handle if the corresponding device is found |
| RT_NULL | No device found |
In general, the hardware timer device name registered to the system is timer0, timer1, etc. The usage examples are as follows:
```c
#define HWTIMER_DEV_NAME "timer0" /* timer name */
rt_device_t hw_dev; /* timer device handle */
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
```
### Open Timer Device
With the device handle, the application can open the device. When the device is open, it will detect whether the device has been initialized. If it is not initialized, it will call the initialization interface to initialize the device by default. Open the device with the following function:
```c
rt_err_t rt_device_open(rt_device_t dev, rt_uint16_t oflags);
```
| Parameter | Description |
| ---------- | ------------------------------- |
| dev | hardware timer device handle |
| oflags | device open mode, is generally opened in read and write mode, which is to take the value：RT_DEVICE_OFLAG_RDWR |
| **return** | —— |
| RT_EOK | device opened successfully |
| other error code | device fail to open |
An example of use is as follows:
```c
#define HWTIMER_DEV_NAME "timer0" /* timer name */
rt_device_t hw_dev; /* timer device handle */
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
/* to open the timer device in read-write mode */
rt_device_open(hw_dev, RT_DEVICE_OFLAG_RDWR);
```
### Set the Timeout Callback Function
Set the timer timeout callback function with the following function - this is the function that will be called when the timer reaches its set count value:
```c
rt_err_t rt_device_set_rx_indicate(rt_device_t dev, rt_err_t (*rx_ind)(rt_device_t dev, rt_size_t size))
```
| Parameter | **Description** |
| ---------- | ------------------------------- |
| dev | device handle |
| rx_ind | timeout callback function, provided by the caller |
| **return** | —— |
| RT_EOK | success |
An example of use is as follows：
```c
#define HWTIMER_DEV_NAME "timer0" /* timer name */
rt_device_t hw_dev; /* timer device handle */
/* timer timeout callback function */
static rt_err_t timeout_cb(rt_device_t dev, rt_size_t size)
{
rt_kprintf("this is hwtimer timeout callback fucntion!\n");
rt_kprintf("tick is :%d !\n", rt_tick_get());
return 0;
}
static int hwtimer_sample(int argc, char *argv[])
{
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
/* open the device in read and write mode */
rt_device_open(hw_dev, RT_DEVICE_OFLAG_RDWR);
/* set the timeout callback function */
rt_device_set_rx_indicate(hw_dev, timeout_cb);
}
```
### Control the Timer Device
By sending control words, the application can configure the hardware timer device with the following function:
```c
rt_err_t rt_device_control(rt_device_t dev, rt_uint8_t cmd, void* arg);
```
| Parameter | **Description** |
| ---------------- | ------------------------------ |
| dev | device handle |
| cmd | command control word |
| arg | controlled parameter |
| **return** | —— |
| RT_EOK | function executed successfully |
| -RT_ENOSYS | execution failed，dev is null |
| other error code | execution failed |
The command control words available for the hardware timer device are as follows：
| **Control word** | Description |
| ---------------------- | ------------------------ |
| HWTIMER_CTRL_FREQ_SET | set the counting frequency |
| HWTIMER_CTRL_STOP | stop the timer |
| HWTIMER_CTRL_INFO_GET | get timer feature information |
| HWTIMER_CTRL_MODE_SET | set timer mode |
Get the timer parameter argument, which is a pointer to the structure struct rt_hwtimer_info, to save the obtained information.
>Setting frequency is valid only when the timer hardware and included driver set the counting frequency. Generally, the default frequency of the driving setting can be used.
When setting the timer mode, the parameter argument can take the following values：
```c
HWTIMER_MODE_ONESHOT /* Single timing */
HWTIMER_MODE_PERIOD /* Periodic timing */
```
An example of using the timer count frequency and timing mode is as follows:
```c
#define HWTIMER_DEV_NAME "timer0" /* timer name */
rt_device_t hw_dev; /* timer device handle */
rt_hwtimer_mode_t mode; /* timer mode */
rt_uint32_t freq = 10000; /* couting frequency */
/* Timer timeout callback function */
static rt_err_t timeout_cb(rt_device_t dev, rt_size_t size)
{
rt_kprintf("this is hwtimer timeout callback fucntion!\n");
rt_kprintf("tick is :%d !\n", rt_tick_get());
return 0;
}
static int hwtimer_sample(int argc, char *argv[])
{
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
/* open the device in read and write mode */
rt_device_open(hw_dev, RT_DEVICE_OFLAG_RDWR);
/* Set the timeout callback function */
rt_device_set_rx_indicate(hw_dev, timeout_cb);
/* Set the counting frequency (1Mhz or the supported minimum counting frequency by default) */
rt_device_control(hw_dev, HWTIMER_CTRL_FREQ_SET, &freq);
/* Set the mode to periodic timer */
mode = HWTIMER_MODE_PERIOD;
rt_device_control(hw_dev, HWTIMER_CTRL_MODE_SET, &mode);
}
```
### Set the Timer Timeout Value
The timer timeout value can be set by the following function：
```c
rt_size_t rt_device_write(rt_device_t dev, rt_off_t pos, const void* buffer, rt_size_t size);
```
| **Parameter** | Description |
| ---------- | ------------------------------------------ |
| dev | device handle |
| pos | write data offset, unused now, can set 0 value |
| buffer | pointer to the timer timeout structure |
| size | timeout structure size |
| **return** | —— |
| The actual size of the written data | |
| 0 | fail |
The prototype of the timeout structure is shown below :
```c
typedef struct rt_hwtimerval
{
rt_int32_t sec; /* second */
rt_int32_t usec; /* microsecond */
} rt_hwtimerval_t;
```
An example of using the timer timeout value is as follows:
```c
#define HWTIMER_DEV_NAME "timer0" /* timer name */
rt_device_t hw_dev; /* timer device handle */
rt_hwtimer_mode_t mode; /* timer mode */
rt_hwtimerval_t timeout_s; /* Timer timeout value */
/* Timer timeout callback function */
static rt_err_t timeout_cb(rt_device_t dev, rt_size_t size)
{
rt_kprintf("this is hwtimer timeout callback fucntion!\n");
rt_kprintf("tick is :%d !\n", rt_tick_get());
return 0;
}
static int hwtimer_sample(int argc, char *argv[])
{
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
/* open the device in read-write mode */
rt_device_open(hw_dev, RT_DEVICE_OFLAG_RDWR);
/* set the timeout callback function */
rt_device_set_rx_indicate(hw_dev, timeout_cb);
/* set the mode as periodic timer */
mode = HWTIMER_MODE_PERIOD;
rt_device_control(hw_dev, HWTIMER_CTRL_MODE_SET, &mode);
/* Set the timer timeout value to 5s and start the timer */
timeout_s.sec = 5; /* second */
timeout_s.usec = 0; /* microsecond */
rt_device_write(hw_dev, 0, &timeout_s, sizeof(timeout_s));
}
```
### Obtain the Current Value of the Timer
The current value of the timer can be obtained by the following function：
```c
rt_size_t rt_device_read(rt_device_t dev, rt_off_t pos, void* buffer, rt_size_t size);
```
| **Parameter** | Description |
| ---------- | ------------------------------------------ |
| dev | timer device handle |
| pos | write data offset, unused now , can set 0 value |
| buffer | output parameter, a pointer point to the timeout structure |
| size | timeout structure size |
| **return** | —— |
| Timeout structure size | success |
| 0 | fail |
An example of use is shown below：
```c
rt_hwtimerval_t timeout_s; /* Used to save the time the timer has elapsed */
/* Read the elapsed time of the timer */
rt_device_read(hw_dev, 0, &timeout_s, sizeof(timeout_s));
```
### Close the Timer Device
The timer device can be closed with the following function:
```c
rt_err_t rt_device_close(rt_device_t dev);
```
| Parameter | Description |
| ---------- | ---------------------------------- |
| dev | timer device handle |
| **return** | —— |
| RT_EOK | close device successfully |
| -RT_ERROR | the device has been completely shut down and cannot be closed repeatedly |
| other error code | fail to close the device |
When a timer device has been used and is not necessary anymore, it should be closed, otherwise the device will remain in an open status.
An example of use is shown below：
```c
#define HWTIMER_DEV_NAME "timer0" /* timer name */
rt_device_t hw_dev; /* timer device handle */
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
... ...
rt_device_close(hw_dev);
```
>Timing errors may occur. Assume that the counter has a maximum value of 0xFFFF, a counting frequency of 1Mhz, and a timing time of 1 second and 1 microsecond. Since the timer can only count up to 65535us at a time, the timing requirement for 1000001us can be completed 20 times at 50000us, and the calculation error will be 1us.
## Hardware Timer Device Usage Example
The specific use of the hardware timer device can refer to the following sample code. The main steps of the sample code are as follows:
1. First find the device handle based on the timer device name "timer0".
2. Open the device "timer0" in read-write mode.
3. Set the timer timeout callback function.
4. Set the timer mode to periodic timer and set the timeout period to 5 seconds. At this time, the timer starts.
5. Read the timer after 3500ms delay, the read value will be displayed in seconds and microseconds.
```c
/*
* Program listing: This is an hwtimer device usage routine
  * The routine exports the hwtimer_sample command to the control terminal
  * Command call format: hwtimer_sample
  * Program function: The hardware timer timeout callback function periodically prints the current tick value, and the difference between the two tick values is converted to the time equivalent to the timing time value.
*/
#include <rtthread.h>
#include <rtdevice.h>
#define HWTIMER_DEV_NAME "timer0" /* timer name */
/* Timer timeout callback function */
static rt_err_t timeout_cb(rt_device_t dev, rt_size_t size)
{
rt_kprintf("this is hwtimer timeout callback fucntion!\n");
rt_kprintf("tick is :%d !\n", rt_tick_get());
return 0;
}
static int hwtimer_sample(int argc, char *argv[])
{
rt_err_t ret = RT_EOK;
rt_hwtimerval_t timeout_s; /* timer timeout value */
rt_device_t hw_dev = RT_NULL; /* timer device value */
rt_hwtimer_mode_t mode; /* timer mode */
/* find timer device */
hw_dev = rt_device_find(HWTIMER_DEV_NAME);
if (hw_dev == RT_NULL)
{
rt_kprintf("hwtimer sample run failed! can't find %s device!\n", HWTIMER_DEV_NAME);
return -RT_ERROR;
}
/* Open the device in read-write mode */
ret = rt_device_open(hw_dev, RT_DEVICE_OFLAG_RDWR);
if (ret != RT_EOK)
{
rt_kprintf("open %s device failed!\n", HWTIMER_DEV_NAME);
return ret;
}
/* set timeout callback function */
rt_device_set_rx_indicate(hw_dev, timeout_cb);
/* Setting mode is periodic timer */
mode = HWTIMER_MODE_PERIOD;
ret = rt_device_control(hw_dev, HWTIMER_CTRL_MODE_SET, &mode);
if (ret != RT_EOK)
{
rt_kprintf("set mode failed! ret is :%d\n", ret);
return ret;
}
/* Set the timer timeout value to 5s and start the timer. */
timeout_s.sec = 5; /* second */
timeout_s.usec = 0; /* microsecond */
if (rt_device_write(hw_dev, 0, &timeout_s, sizeof(timeout_s)) != sizeof(timeout_s))
{
rt_kprintf("set timeout value failed\n");
return -RT_ERROR;
}
/* delay 3500ms */
rt_thread_mdelay(3500);
/* read the current value of timer */
rt_device_read(hw_dev, 0, &timeout_s, sizeof(timeout_s));
rt_kprintf("Read: Sec = %d, Usec = %d\n", timeout_s.sec, timeout_s.usec);
return ret;
}
/* Export to the msh command list */
MSH_CMD_EXPORT(hwtimer_sample, hwtimer sample);
```

BIN
documentation/device/i2c/figures/i2c1.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 9.5 KiB

BIN
documentation/device/i2c/figures/i2c2.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 15 KiB

BIN
documentation/device/i2c/figures/i2c3.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 7.6 KiB

298
documentation/device/i2c/i2c.md Normal file
View file

@ -0,0 +1,298 @@
# I2C Bus Device
## Introduction of I2C
The I2C (Inter Integrated Circuit) bus is a half-duplex, bidirectional two-wire synchronous serial bus developed by Philips. The I2C bus has only two signal lines, one is the bidirectional data line SDA (serial data), and the other is the bidirectional clock line SCL (serial clock). Compared to the SPI bus, which has two lines for receiving data and transmitting data between the master and slave devices, the I2C bus uses only one line for data transmission and reception.
Like SPI, I2C works in a master-slave manner. Unlike SPI-master-multi-slave architecture, it allows multiple master devices to exist at the same time. Each device connected to the bus has a unique address, and the master device initiates data transfer, and generates a clock signal. The slave device is addressed by the master device, and only one master device is allowed to communicate at a time. As shown below:
![I2C Bus master-slave device connection mode](figures/i2c1.png)
The main data transmission format of the I2C bus is shown in the following figure:
![I2C Bus Data Transmission Format](figures/i2c2.png)
When the bus is idle, both SDA and SCL are in a high state. When the host wants to communicate with a slave, it will send a start condition first, then send the slave address and read and write control bits, and then transfer the data (the host can send or receive data). The host will send a stop condition when the data transfer ends. Each byte transmitted is 8 bits, with the high bit first and the low bit last. The different terms in the data transmission process are as follows:
* **Starting Condition：** When SCL is high, the host pulls SDA low, indicating that data transfer is about to begin.
* **Slave Address：** The first byte sent by the master is the slave address, the upper 7 bits are the address, the lowest bit is the R/W read/write control bit, R/W bit equals to 1 means the read operation, and 0 means the write operation. The general slave address has 7-bit address mode and 10-bit address mode. In the 10-bit address mode, the first 7 bits of the first byte are a combination of 11110XX, where the last two bits (XX) are two highest 10-bit addresses. The second byte is the remaining 8 bits of the 10-bit slave address, as shown in the following figure:
![7-bit address and 10-bit address format](figures/i2c3.png)
* **Answer Signal：** Each time a byte of data is transmitted, the receiver needs to reply with an ACK (acknowledge). The slave sends an ACK when writing data and the ACK by the host when reading data. When the host reads the last byte of data, it can send NACK (Not acknowledge) and then stop the condition.
* **Data：** After the slave address is sent, some commands may be sent, depending on the slave, and then the data transmission starts, and is sent by the master or the slave. Each data is 8 bits, and the number of bytes of data is not limited.
* **Repeat Start Condition：** In a communication process, when the host may need to transfer data with different slaves or need to switch read and write operations, the host can send another start condition.
* **Stop Condition：** When SDA is low, the master pulls SCL high and stays high, then pulls SDA high to indicate the end of the transfer.
## Access to I2C Bus Devices
In general, the MCU's I2C device communicates as a master and slave. In the RT-Thread, the I2C master is virtualized as an I2C bus device. The I2C slave communicates with the I2C bus through the I2C device interface. The related interfaces are as follows:
| **Function** | **Description** |
| --------------- | ---------------------------------- |
| rt_device_find() | Find device handles based on I2C bus device name |
| rt_i2c_transfer() | transfer data |
### Finding I2C Bus Device
Before using the I2C bus device, you need to obtain the device handle according to the I2C bus device name, so that you can operate the I2C bus device. The device function is as follows.
```c
rt_device_t rt_device_find(const char* name);
```
| Parameter | Description |
| -------- | ---------------------------------- |
| name | I2C bus device name |
| **Return Value** | —— |
| device handle | Finding the corresponding device will return the corresponding device handle |
| RT_NULL | No corresponding device object found |
In general, the name of the I2C device registered to the system is i2c0, i2c1, etc. The usage examples are as follows:
```c
#define AHT10_I2C_BUS_NAME "i2c1" /* Sensor connected I2C bus device name */
struct rt_i2c_bus_device *i2c_bus; /* I2C bus device handle */
/* Find the I2C bus device and get the I2C bus device handle */
i2c_bus = (struct rt_i2c_bus_device *)rt_device_find(name);
```
### Data Transmission
You can use `rt_i2c_transfer()` for data transfer by getting the I2C bus device handle. The function prototype is as follows:
```c
rt_size_t rt_i2c_transfer(struct rt_i2c_bus_device *bus,
struct rt_i2c_msg msgs[],
rt_uint32_t num);
```
| Parameter | Description |
|--------------------|----------------------|
| bus | I2C bus device handle |
| msgs[] | Message array pointer to be transmitted |
| num | The number of elements in the message array |
| **Return Value** | —— |
| the number of elements in the message array | succeeded |
| error code | failed |
Like the custom transport interface of the SPI bus, the data transmitted by the custom transport interface of the I2C bus is also in units of one message. The parameter msgs[] points to the array of messages to be transmitted. The user can customize the content of each message to implement two different data transmission modes supported by the I2C bus. If the master needs to send a repeat start condition, it will need to send 2 messages.
>This function will call rt_mutex_take(), which cannot be called inside the interrupt service routine, which will cause assertion to report an error.
The prototypes of the I2C message data structure are as follows:
```c
struct rt_i2c_msg
{
rt_uint16_t addr; /* Slave address */
rt_uint16_t flags; /* Reading, writing signs, etc. */
rt_uint16_t len; /* Read and write data bytes */
rt_uint8_t *buf; /* Read and write data buffer pointer　*/
}
```
Slave address (addr): Supports 7-bit and 10-bit binary addresses. You need to view the data sheets of different devices.
>The slave address used by the RT-Thread I2C device interface does not contain read/write bits. The read/write bit control needs to modify the flag `flags`.
The flags `flags` can be defined as macros that can be combined with other macros using the bitwise operation "|" as needed.
```c
#define RT_I2C_WR 0x0000 /* Write flag */
#define RT_I2C_RD (1u << 0) /* Read flag */
#define RT_I2C_ADDR_10BIT (1u << 2) /* 10-bit address mode */
#define RT_I2C_NO_START (1u << 4) /* No start condition */
#define RT_I2C_IGNORE_NACK (1u << 5) /* Ignore NACK */
#define RT_I2C_NO_READ_ACK (1u << 6) /* Do not send ACK when reading */
```
Examples of use are as follows:
```c
#define AHT10_I2C_BUS_NAME "i2c1" /* Sensor connected I2C bus device name */
#define AHT10_ADDR 0x38 /* Slave address */
struct rt_i2c_bus_device *i2c_bus; /* I2C bus device handle */
/* Find the I2C bus device and get the I2C bus device handle */
i2c_bus = (struct rt_i2c_bus_device *)rt_device_find(name);
/* Read sensor register data */
static rt_err_t read_regs(struct rt_i2c_bus_device *bus, rt_uint8_t len, rt_uint8_t *buf)
{
struct rt_i2c_msg msgs;
msgs.addr = AHT10_ADDR; /* Slave address */
msgs.flags = RT_I2C_RD; /* Read flag */
msgs.buf = buf; /* Read and write data buffer pointer　*/
msgs.len = len; /* Read and write data bytes */
/* Call the I2C device interface to transfer data */
if (rt_i2c_transfer(bus, &msgs, 1) == 1)
{
return RT_EOK;
}
else
{
return -RT_ERROR;
}
}
```
## I2C Bus Device Usage Example
The specific usage of the I2C device can be referred to the following sample code. The main steps of the sample code are as follows:
1. First find the I2C name based on the I2C device name, get the device handle, and then initialize the aht10 sensor.
2. The two functions that control the sensor are the write sensor register `write_reg()` and the read sensor register `read_regs()`, both called `rt_i2c_transfer()` to transfer the data. The function `read_temp_humi()` calls the above two functions to read the temperature and humidity information.
```c
/*
* Program listing: This is an I2C device usage routine
* The routine exports the i2c_aht10_sample command to the control terminal
* Command call format: i2c_aht10_sample i2c1
* Command explanation: The second parameter of the command is the name of the I2C bus device to be used. If it is empty, the default I2C bus device is used.
* Program function: read the temperature and humidity data of the aht10 sensor and print.
*/
#include <rtthread.h>
#include <rtdevice.h>
#define AHT10_I2C_BUS_NAME "i2c1" /* Sensor connected I2C bus device name */
#define AHT10_ADDR 0x38 /* Slave address */
#define AHT10_CALIBRATION_CMD 0xE1 /* Calibration command */
#define AHT10_NORMAL_CMD 0xA8 /* General command */
#define AHT10_GET_DATA 0xAC /* Get data command */
static struct rt_i2c_bus_device *i2c_bus = RT_NULL; /* I2C bus device handle */
static rt_bool_t initialized = RT_FALSE; /* Sensor initialization status */
/* Write sensor register */
static rt_err_t write_reg(struct rt_i2c_bus_device *bus, rt_uint8_t reg, rt_uint8_t *data)
{
rt_uint8_t buf[3];
struct rt_i2c_msg msgs;
buf[0] = reg; //cmd
buf[1] = data[0];
buf[2] = data[1];
msgs.addr = AHT10_ADDR;
msgs.flags = RT_I2C_WR;
msgs.buf = buf;
msgs.len = 3;
/* Call the I2C device interface to transfer data */
if (rt_i2c_transfer(bus, &msgs, 1) == 1)
{
return RT_EOK;
}
else
{
return -RT_ERROR;
}
}
/* Read sensor register data */
static rt_err_t read_regs(struct rt_i2c_bus_device *bus, rt_uint8_t len, rt_uint8_t *buf)
{
struct rt_i2c_msg msgs;
msgs.addr = AHT10_ADDR;
msgs.flags = RT_I2C_RD;
msgs.buf = buf;
msgs.len = len;
/* Call the I2C device interface to transfer data */
if (rt_i2c_transfer(bus, &msgs, 1) == 1)
{
return RT_EOK;
}
else
{
return -RT_ERROR;
}
}
static void read_temp_humi(float *cur_temp, float *cur_humi)
{
rt_uint8_t temp[6];
write_reg(i2c_bus, AHT10_GET_DATA, 0); /* send command */
rt_thread_mdelay(400);
read_regs(i2c_bus, 6, temp); /* obtian sensor data */
/* Humidity data conversion */
*cur_humi = (temp[1] << 12 | temp[2] << 4 | (temp[3] & 0xf0) >> 4) * 100.0 / (1 << 20);
/* Temperature data conversion */
*cur_temp = ((temp[3] & 0xf) << 16 | temp[4] << 8 | temp[5]) * 200.0 / (1 << 20) - 50;
}
static void aht10_init(const char *name)
{
rt_uint8_t temp[2] = {0, 0};
/* Find the I2C bus device and get the I2C bus device handle */
i2c_bus = (struct rt_i2c_bus_device *)rt_device_find(name);
if (i2c_bus == RT_NULL)
{
rt_kprintf("can't find %s device!\n", name);
}
else
{
write_reg(i2c_bus, AHT10_NORMAL_CMD, temp);
rt_thread_mdelay(400);
temp[0] = 0x08;
temp[1] = 0x00;
write_reg(i2c_bus, AHT10_CALIBRATION_CMD, temp);
rt_thread_mdelay(400);
initialized = RT_TRUE;
}
}
static void i2c_aht10_sample(int argc, char *argv[])
{
float humidity, temperature;
char name[RT_NAME_MAX];
humidity = 0.0;
temperature = 0.0;
if (argc == 2)
{
rt_strncpy(name, argv[1], RT_NAME_MAX);
}
else
{
rt_strncpy(name, AHT10_I2C_BUS_NAME, RT_NAME_MAX);
}
if (!initialized)
{
/* Sensor initialization */
aht10_init(name);
}
if (initialized)
{
/* Read temperature and humidity data */
read_temp_humi(&temperature, &humidity);
rt_kprintf("read aht10 sensor humidity : %d.%d %%\n", (int)humidity, (int)(humidity * 10) % 10);
rt_kprintf("read aht10 sensor temperature: %d.%d \n", (int)temperature, (int)(temperature * 10) % 10);
}
else
{
rt_kprintf("initialize sensor failed!\n");
}
}
/* Export to the msh command list */
MSH_CMD_EXPORT(i2c_aht10_sample, i2c aht10 sample);
```

BIN
documentation/device/pin/figures/pin2.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 16 KiB

353
documentation/device/pin/pin.md Normal file
View file

@ -0,0 +1,353 @@
# PIN Device
## Introduction of Pin
The pins on the chip are generally divided into four categories: power supply, clock, control, and I/O. The I/O pins are further divided into General Purpose Input Output (GPIO) and function-multiplexed I/O (such as SPI/I2C/UART, etc.) pins, referring to their usage mode.
Most MCU pins have more than one function. Their internal structure is different and their supported functionality are different. The actual function of the pin can be switched through different configurations. The main features of the General Purpose Input Output (GPIO) port are as follows:
* Programmable Interrupt: The interrupt trigger mode is configurable. Generally, there are five interrupt trigger modes as shown in the following figure:
![5 Interrupt Trigger Modes](figures/pin2.png)
* Input and output modes can be controlled.
* Output modes generally include Output push-pull, Output open-drain, Output pull-up, and Output pull-down. When the pin is in the output mode, the connected peripherals can be controlled by configuring the level of the pin output to be high or low.
* Input modes generally include: Input floating, Input pull-up, Input pull-down, and Analog. When the pin is in the input mode, the level state of the pin can be read, that is, high level or low level.
## Access PIN Device
The application accesses the GPIO through the PIN device management interface provided by RT-Thread. The related interfaces are as follows:
| Function | **Description** |
| ---------------- | ---------------------------------- |
| rt_pin_mode() | Set pin mode |
| rt_pin_write() | Set the pin level |
| rt_pin_read() | Read pin level |
| rt_pin_attach_irq() | Bind pin interrupt callback function |
| rt_pin_irq_enable() | Enable pin interrupt |
| rt_pin_detach_irq() | Detach pin interrupt callback function |
### Obtain Pin Number
The pin numbers provided by RT-Thread need to be distinguished from the chip pin numbers, which not the same. The pin numbers are defined by the PIN device driver and are related to the specific chip used. There are two ways to obtain the pin number: use the macro definition or view the PIN driver file.
#### Use Macro Definition
If you use the BSP in the `rt-thread/bsp/stm32` directory, you can use the following macro to obtain the pin number:
```c
GET_PIN(port, pin)
```
The sample code for the pin number corresponding to LED0 with pin number PF9 is as follows:
```c
#define LED0_PIN GET_PIN(F, 9)
```
#### View Driver Files
If you use a different BSP, you will need to check the PIN driver code `drv_gpio.c` file to confirm the pin number. There is an array in this file that holds the number information for each PIN pin, as shown below:
```c
static const rt_uint16_t pins[] =
{
__STM32_PIN_DEFAULT,
__STM32_PIN_DEFAULT,
__STM32_PIN(2, A, 15),
__STM32_PIN(3, B, 5),
__STM32_PIN(4, B, 8),
__STM32_PIN_DEFAULT,
__STM32_PIN_DEFAULT,
__STM32_PIN_DEFAULT,
__STM32_PIN(8, A, 14),
__STM32_PIN(9, B, 6),
... ...
}
```
Take `__STM32_PIN(2, A, 15)` as an example, 2 is the pin number used by RT-Thread, A is the port number, and 15 is the pin number, so the pin number corresponding to PA15 is 2.
### Set Pin Mode
Before the pin is used, you need to set the input or output mode first, and the following functions are used:
```c
void rt_pin_mode(rt_base_t pin, rt_base_t mode);
```
| Parameter | **Discription** |
| --------- | ------------------ |
| pin | Pin number |
| mode | Pin operation mode |
At present, the pin working mode supported by RT-Thread can take one of the five macro definition values as shown. The mode supported by the chip corresponding to each mode needs to refer to the specific implementation of the PIN device driver:
```c
#define PIN_MODE_OUTPUT 0x00 /* Output */
#define PIN_MODE_INPUT 0x01 /* Input */
#define PIN_MODE_INPUT_PULLUP 0x02 /* input Pull up */
#define PIN_MODE_INPUT_PULLDOWN 0x03 /* input Pull down */
#define PIN_MODE_OUTPUT_OD 0x04 /* output Open drain */
```
An example of use is as follows:
```c
#define BEEP_PIN_NUM 35 /* PB0 */
/* Buzzer pin is in output mode */
rt_pin_mode(BEEP_PIN_NUM, PIN_MODE_OUTPUT);
```
### Set The Pin Level
The function to set the pin output level is as follows:
```c
void rt_pin_write(rt_base_t pin, rt_base_t value);
```
| **Parameter** | Discription |
|----------|-------------------------|
| pin | Pin number |
| value | Level logic value, which can take one of two macro definition values: PIN_LOW means low level, or PIN_HIGH means high level |
Examples of use are as follows:
```c
#define BEEP_PIN_NUM 35 /* PB0 */
/* Beep's pin is in output mode */
rt_pin_mode(BEEP_PIN_NUM, PIN_MODE_OUTPUT);
/* Set low level */
rt_pin_write(BEEP_PIN_NUM, PIN_LOW);
```
### Read Pin Level
The functions to read the pin level are as follows:
```c
int rt_pin_read(rt_base_t pin);
```
| Parameter | Description |
| ---------- | ----------- |
| pin | Pin number |
| **return** | —— |
| PIN_LOW | Low level |
| PIN_HIGH | High level |
Examples of use are as follows:
```c
#define BEEP_PIN_NUM 35 /* PB0 */
int status;
/* Buzzer pin is in output mode */
rt_pin_mode(BEEP_PIN_NUM, PIN_MODE_OUTPUT);
/* Set low level */
rt_pin_write(BEEP_PIN_NUM, PIN_LOW);
status = rt_pin_read(BEEP_PIN_NUM);
```
### Bind Pin Interrupt Callback Function
To use the interrupt functionality of a pin, you can use the following function to configure the pin to some interrupt trigger mode and bind an interrupt callback function to the corresponding pin. When the pin interrupt occurs, the callback function will be executed.:
```c
rt_err_t rt_pin_attach_irq(rt_int32_t pin, rt_uint32_t mode,
void (*hdr)(void *args), void *args);
```
| Parameter | Description |
| ---------- | ------------------------------------------------------------ |
| pin | Pin number |
| mode | Interrupt trigger mode |
| hdr | Interrupt callback function. Users need to define this function |
| args | Interrupt the parameters of the callback function, set to RT_NULL when not needed |
| return | —— |
| RT_EOK | Binding succeeded |
| error code | Binding failed |
Interrupt trigger mode mode can take one of the following five macro definition values:
```c
#define PIN_IRQ_MODE_RISING 0x00 /* Rising edge trigger */
#define PIN_IRQ_MODE_FALLING 0x01 /* Falling edge trigger */
#define PIN_IRQ_MODE_RISING_FALLING 0x02 /* Edge trigger (triggered on both rising and falling edges)*/
#define PIN_IRQ_MODE_HIGH_LEVEL 0x03 /* High level trigger */
#define PIN_IRQ_MODE_LOW_LEVEL 0x04 /* Low level trigger */
```
Examples of use are as follows:
```c
#define KEY0_PIN_NUM 55 /* PD8 */
/* Interrupt callback function */
void beep_on(void *args)
{
rt_kprintf("turn on beep!\n");
rt_pin_write(BEEP_PIN_NUM, PIN_HIGH);
}
static void pin_beep_sample(void)
{
/* Button 0 pin is the input mode */
rt_pin_mode(KEY0_PIN_NUM, PIN_MODE_INPUT_PULLUP);
/* Bind interrupt, rising edge mode, callback function named beep_on */
rt_pin_attach_irq(KEY0_PIN_NUM, PIN_IRQ_MODE_FALLING, beep_on, RT_NULL);
}
```
### Enable Pin Interrupt
After binding the pin interrupt callback function, use the following function to enable pin interrupt:
```c
rt_err_t rt_pin_irq_enable(rt_base_t pin, rt_uint32_t enabled);
```
| **Parameter** | **Description** |
|----------|----------------|
| pin | Pin number |
| enabled | Status, one of two values: PIN_IRQ_ENABLE, and PIN_IRQ_DISABLE |
| **return** | —— |
| RT_EOK | Enablement succeeded |
| error code | Enablement failed |
Examples of use are as follows:
```c
#define KEY0_PIN_NUM 55 /* PD8 */
/* Interrupt callback function */
void beep_on(void *args)
{
rt_kprintf("turn on beep!\n");
rt_pin_write(BEEP_PIN_NUM, PIN_HIGH);
}
static void pin_beep_sample(void)
{
/* Key 0 pin is the input mode */
rt_pin_mode(KEY0_PIN_NUM, PIN_MODE_INPUT_PULLUP);
/* Bind interrupt, rising edge mode, callback function named beep_on */
rt_pin_attach_irq(KEY0_PIN_NUM, PIN_IRQ_MODE_FALLING, beep_on, RT_NULL);
/* Enable interrupt */
rt_pin_irq_enable(KEY0_PIN_NUM, PIN_IRQ_ENABLE);
}
```
### Detach Pin Interrupt Callback Function
You can use the following function to detach the pin interrupt callback function:
```c
rt_err_t rt_pin_detach_irq(rt_int32_t pin);
```
| **Parameter** | **Description** |
| ------------- | -------------------- |
| pin | Pin number |
| **return** | —— |
| RT_EOK | Detachment succeeded |
| error code | Detachment failed |
After the pin detaches the interrupt callback function, the interrupt is not closed. You can also call the bind interrupt callback function to bind the other callback functions again.
```c
#define KEY0_PIN_NUM 55 /* PD8 */
/* Interrupt callback function */
void beep_on(void *args)
{
rt_kprintf("turn on beep!\n");
rt_pin_write(BEEP_PIN_NUM, PIN_HIGH);
}
static void pin_beep_sample(void)
{
/* Key 0 pin is the input mode */
rt_pin_mode(KEY0_PIN_NUM, PIN_MODE_INPUT_PULLUP);
/* Bind interrupt, rising edge mode, callback function named beep_on */
rt_pin_attach_irq(KEY0_PIN_NUM, PIN_IRQ_MODE_FALLING, beep_on, RT_NULL);
/* Enable interrupt */
rt_pin_irq_enable(KEY0_PIN_NUM, PIN_IRQ_ENABLE);
/* Detach interrupt callback function */
rt_pin_detach_irq(KEY0_PIN_NUM);
}
```
## PIN Device Usage Example
The following sample code is the pin device usage example. The main steps of the sample code are as follows:
1. Set the corresponding pin of the beep to the output mode and give a default low state.
2. Set the key 0 and button 1 corresponding to the input mode, then bind the interrupt callback function and enable the interrupt.
3. When the key 0 is pressed, the beep starts to sound, and when the key 1 is pressed, the beep stops.
```c
/*
* Program listing: This is a PIN device usage routine
* The routine exports the pin_beep_sample command to the control terminal
* Command call format：pin_beep_sample
* Program function: control the buzzer by controlling the level state of the corresponding pin of the buzzer by pressing the button
*/
#include <rtthread.h>
#include <rtdevice.h>
/* Pin number, determined by looking at the device driver file drv_gpio.c */
#ifndef BEEP_PIN_NUM
#define BEEP_PIN_NUM 35 /* PB0 */
#endif
#ifndef KEY0_PIN_NUM
#define KEY0_PIN_NUM 55 /* PD8 */
#endif
#ifndef KEY1_PIN_NUM
#define KEY1_PIN_NUM 56 /* PD9 */
#endif
void beep_on(void *args)
{
rt_kprintf("turn on beep!\n");
rt_pin_write(BEEP_PIN_NUM, PIN_HIGH);
}
void beep_off(void *args)
{
rt_kprintf("turn off beep!\n");
rt_pin_write(BEEP_PIN_NUM, PIN_LOW);
}
static void pin_beep_sample(void)
{
/* Beep pin is in output mode */
rt_pin_mode(BEEP_PIN_NUM, PIN_MODE_OUTPUT);
/* Default low level */
rt_pin_write(BEEP_PIN_NUM, PIN_LOW);
/* KEY 0 pin is the input mode */
rt_pin_mode(KEY0_PIN_NUM, PIN_MODE_INPUT_PULLUP);
/* Bind interrupt, falling edge mode, callback function named beep_on */
rt_pin_attach_irq(KEY0_PIN_NUM, PIN_IRQ_MODE_FALLING, beep_on, RT_NULL);
/* Enable interrupt */
rt_pin_irq_enable(KEY0_PIN_NUM, PIN_IRQ_ENABLE);
/* KEY 1 pin is input mode */
rt_pin_mode(KEY1_PIN_NUM, PIN_MODE_INPUT_PULLUP);
/* Binding interrupt, falling edge mode, callback function named beep_off */
rt_pin_attach_irq(KEY1_PIN_NUM, PIN_IRQ_MODE_FALLING, beep_off, RT_NULL);
/* Enable interrupt */
rt_pin_irq_enable(KEY1_PIN_NUM, PIN_IRQ_ENABLE);
}
/* Export to the msh command list */
MSH_CMD_EXPORT(pin_beep_sample, pin beep sample);
```

BIN
documentation/device/pwm/figures/pwm-f.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 15 KiB

BIN
documentation/device/pwm/figures/pwm-l.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 10 KiB

260
documentation/device/pwm/pwm.md Normal file
View file

@ -0,0 +1,260 @@
# PWM Device
## Introduction to PWM
PWM (Pulse Width Modulation) is a method of digitally encoding the level of an analog signal. The frequency of the square wave is used to encode the level of a specific analog signal by pulses of different frequencies. The output receives a series of pulses of equal magnitude and uses these pulses to replace the device with the desired waveform.
![PWM Schematic Diagram](figures/pwm-f.png)
Above is a simple schematic diagram of PWM. Assuming that the timer works in a up-counter mode. When the count value is less than the threshold, it outputs a level state, such as a high level. When the count value is greater than the threshold, it outputs the opposite, such as a low level. When the count value reaches the maximum value, the counter recounts from 0 and returns to the original level state. The ratio of the high-level duration (pulse width) to the cycle time is the duty cycle, ranging from 0 to 100%. The high level of the above picture is just half of the cycle time, so the duty cycle is 50%.
One of the common PWM control scenarios is to adjust the brightness of a light or screen. The brightness can be adjusted through changing the duty cycle. The PWM does not adjust the light continuously, rather it constantly turns the screen on and off. When the light is turned on and off fast enough, the naked eye will always think that it is always bright. In the process of switching it on and off, the longer the light is off, the lower the brightness of the screen to the naked eye. Conversely, the longer the light is on, the brighter the screen will appear.
![PWM Brightness Adjustment](figures/pwm-l.png)
## Access to PWM Devices
The application accesses the PWM device hardware through the PWM device management interface provided by RT-Thread. The related interfaces are as follows:
| **Function** | Description |
| ----------------- | ---------------------------------- |
| rt_device_find() | Find device handles based on the name of PWM device |
| rt_pwm_set() | Set PWM period and pulse width |
| rt_pwm_enable() | Enable PWM device |
| rt_pwm_disable() | Disable the PWM device |
### Find the PWM Device
The application obtains the device handle based on the name of PWM device, which in turn can operate the PWM device. The function is as follows:
```c
rt_device_t rt_device_find(const char* name);
```
| Parameter | Description |
| -------- | ---------------------------------- |
| name | Device |
| **Return** | —— |
| Device handle | Found the corresponding device, will return the corresponding device handle |
| RT_NULL | Device not found |
In general, the name of the PWM device registered to the system is pwm0, pwm1, etc. The usage examples are as follows:
```c
#define PWM_DEV_NAME "pwm3" /* name of PWM device */
struct rt_device_pwm *pwm_dev; /* PWM device handle */
/* Search the device */
pwm_dev = (struct rt_device_pwm *)rt_device_find(PWM_DEV_NAME);
```
### Set PWM Period and Pulse Width
Set the PWM period and duty cycle by using the following function:
```c
rt_err_t rt_pwm_set(struct rt_device_pwm *device,
int channel,
rt_uint32_t period,
rt_uint32_t pulse);
```
| Parameter | Description |
| ---------- | ----------------- |
| device | PWM device handle |
| channel | PWM channel |
| period | PWM period (ns) |
| pulse | PWM pulse width time (ns) |
| **Return** | —— |
| RT_EOK | successful |
| -RT_EIO | device is null |
| -RT_ENOSYS | Device operation method is null |
| Other Errors | Execute failed |
The output frequency of the PWM is determined by the period. For example, the time of a period is 0.5ms (milliseconds), the period value is 500000ns (nanoseconds), the output frequency is 2KHz, the duty cycle is `pulse / period`, and the pulse value cannot exceed period.
An example of use is as follows:
```c
#define PWM_DEV_NAME "pwm3" /* name of PWM device */
#define PWM_DEV_CHANNEL 4 /* PWM channel */
struct rt_device_pwm *pwm_dev; /* PWM device handle */
rt_uint32_t period, pulse;
period = 500000; /* The period is 0.5ms, the unit is nanoseconds */
pulse = 0; /* PWM pulse width value, the unit is nanoseconds */
/* Search the device */
pwm_dev = (struct rt_device_pwm *)rt_device_find(PWM_DEV_NAME);
/* Set the PWM period and pulse width */
rt_pwm_set(pwm_dev, PWM_DEV_CHANNEL, period, pulse);
```
### Enable the PWM Device
After setting the PWM period and pulse width, you can enable the PWM device by the following function:
```c
rt_err_t rt_pwm_enable(struct rt_device_pwm *device, int channel);
```
| Parameter | Description |
| ---------- | ------------------------------- |
| device | PWM device handle |
| channel | PWM channel |
| **Return** | —— |
| RT_EOK | Enable device successful |
| -RT_ENOSYS | Device operation method is null |
| Other Errors | Enable device failed |
An example of use is as follows:
```c
#define PWM_DEV_NAME "pwm3" /* name of PWM device */
#define PWM_DEV_CHANNEL 4 /* PWM channel */
struct rt_device_pwm *pwm_dev; /* PWM device handle */
rt_uint32_t period, pulse;
period = 500000; /* The period is 0.5ms, the unit is nanoseconds */
pulse = 0; /* PWM pulse width value, the unit is nanoseconds */
/* Search the device */
pwm_dev = (struct rt_device_pwm *)rt_device_find(PWM_DEV_NAME);
/* Set the PWM period and pulse width */
rt_pwm_set(pwm_dev, PWM_DEV_CHANNEL, period, pulse);
/* Enable the device */
rt_pwm_enable(pwm_dev, PWM_DEV_CHANNEL);
```
### Disable the PWM device Channel
Use the following function to turn off the corresponding channel of the PWM device.
```c
rt_err_t rt_pwm_disable(struct rt_device_pwm *device, int channel);
```
| **Parameter** | Description |
| ---------- | ------------------------------- |
| device | PWM device handle |
| channel | PWM channel |
| **Return** | —— |
| RT_EOK | Turn off device successful |
| -RT_EIO | Device handle is null |
| Other Errors | Turn off device failed |
An example of use is as follows:
```c
#define PWM_DEV_NAME "pwm3" /* name of PWM device */
#define PWM_DEV_CHANNEL 4 /* PWM channel */
struct rt_device_pwm *pwm_dev; /* PWM device handle */
rt_uint32_t period, pulse;
period = 500000; /* The period is 0.5ms, the unit is nanoseconds */
pulse = 0; /* PWM pulse width value, the unit is nanoseconds */
/* Search the device */
pwm_dev = (struct rt_device_pwm *)rt_device_find(PWM_DEV_NAME);
/* Set the PWM period and pulse width */
rt_pwm_set(pwm_dev, PWM_DEV_CHANNEL, period, pulse);
/* Enable the device */
rt_pwm_enable(pwm_dev, PWM_DEV_CHANNEL);
/* Turn off the device channel */
rt_pwm_disable(pwm_dev,PWM_DEV_CHANNEL);
```
## FinSH Command
To set the period and duty cycle of a channel of a PWM device, use the command `pwm_set pwm1 1 500000 5000`. The first parameter is the command, the second parameter is the PWM device name, the third parameter is the PWM channel, and the fourth parameter is PWM period (ns), the fifth parameter is the pulse width (ns).
```c
msh />pwm_set pwm1 1 500000 5000
msh />
```
To enable a channel of the PWM device, use the command `pwm_enable pwm1 1`. The first parameter is the command, the second parameter is the PWM device name, and the third parameter is the PWM channel.
```c
msh />pwm_enable pwm1 1
msh />
```
To disable a channel of the PWM device, use the command `pwm_disable pwm1 1`. The first parameter is the command, the second parameter is the PWM device name, and the third parameter is the PWM channel.
```c
msh />pwm_disable pwm1 1
msh />
```
## PWM Device Usage Example
The following sample code is a PWM device usage sample . The main steps of the sample code are as follows:
1. Find the PWM device to get the device handle.
2. Set the PWM period and pulse width.
3. Enable the PWM device.
4. The pulse width is modified every 50 milliseconds in the while loop.
5. Connect the PWM channel to a LED, and you can see that the LED changes from dark to bright gradually, and then from bright to dark.
```c
/*
* Program list: This is PWM device usage example
* The routine exports the pwm_led_sample command to the control terminal
* Format for Command: pwm_led_sample
* Program function: By controlling the brightness of the LED light through the PWM device,
* you can see that the LED changes from dark to bright gradually, then from bright to dark.
*/
#include <rtthread.h>
#include <rtdevice.h>
#define PWM_DEV_NAME "pwm3" /* PWM device name */
#define PWM_DEV_CHANNEL 4 /* PWM channel */
struct rt_device_pwm *pwm_dev; /* PWM device handle */
static int pwm_led_sample(int argc, char *argv[])
{
rt_uint32_t period, pulse, dir;
period = 500000; /* The period is 0.5ms, the unit is nanoseconds */
dir = 1; /* Increase or decrease direction of PWM pulse width value */
pulse = 0; /* PWM pulse width value, the unit is nanoseconds*/
/* Search the Device */
pwm_dev = (struct rt_device_pwm *)rt_device_find(PWM_DEV_NAME);
if (pwm_dev == RT_NULL)
{
rt_kprintf("pwm sample run failed! can't find %s device!\n", PWM_DEV_NAME);
return -RT_ERROR;
}
/* Set PWM period and pulse width defaults */
rt_pwm_set(pwm_dev, PWM_DEV_CHANNEL, period, pulse);
/* Enable device */
rt_pwm_enable(pwm_dev, PWM_DEV_CHANNEL);
while (1)
{
rt_thread_mdelay(50);
if (dir)
{
pulse += 5000; /* Increase 5000ns each time from 0 */
}
else
{
pulse -= 5000; /* 5000ns reduction from the maximum */
}
if (pulse >= period)
{
dir = 0;
}
if (0 == pulse)
{
dir = 1;
}
/* Set the PWM period and pulse width */
rt_pwm_set(pwm_dev, PWM_DEV_CHANNEL, period, pulse);
}
}
/* Export to the msh command list */
MSH_CMD_EXPORT(pwm_led_sample, pwm sample);
```

198
documentation/device/rtc/rtc.md Normal file
View file

@ -0,0 +1,198 @@
# RTC Device
## Introduction of RTC
The RTC (Real-Time Clock) provides accurate real-time clock time, which can be used to generate information such as year, month, day, hour, minute, and second. At present, most real-time clock chips use a higher precision crystal oscillator as a clock source. In order to work when the main power supply is powered down, some clock chips will be powered by a battery to keep the time information valid.
The RT-Thread RTC device provides the basic services for the operating system's time system. RTCs find many uses in IoT scenarios, and even in secure transmission processes such as SSL, RTC has become an indispensable part.
## Access RTC Devices
The application accesses the RTC hardware through the RTC device management interface, and the relevant interfaces are as follows:
| **Function** | Description |
| ------------- | ---------------------------------- |
| set_date() | Set date, year, month, day |
| set_time() | Set time, hour, minute, second |
| time() | Obtain current time |
### Set Date
Set the current date value of the RTC device by the following functions:
```c
rt_err_t set_date(rt_uint32_t year, rt_uint32_t month, rt_uint32_t day)
```
| **Parameter** | **Description** |
| -------- | ---------------------------------- |
|year |The year to be set to take effect|
|month |The month to be set to take effect|
|day | The date to be set to take effect |
| **return** | —— |
| RT_EOK | Set-up succeeded |
| -RT_ERROR | Set-up failed, no rtc device found |
| other error code | Set-up failed |
An example of use is as follows:
```c
/* Set the date to December 3, 2018 */
set_date(2018, 12, 3);
```
### Set Time
Set the current time value of the RTC device by the following function:
```c
rt_err_t set_time(rt_uint32_t hour, rt_uint32_t minute, rt_uint32_t second)
```
| **Parameter** | **Description** |
| ---------- | ------------------------------- |
|hour |The hour to be set to take effect|
|minute |The minute to be set to take effect|
|second |The second to be set to take effect|
| **return** | —— |
| RT_EOK | Set-up succeeded |
| -RT_ERROR | Set-up failed, no rtc device found |
| other error code | Set-up failed |
An example of use is as follows:
```c
/* Set the time to 11:15:50 */
set_time(11, 15, 50);
```
### Obtain Current Time
Obtain time using the time API in the C standard library:
```c
time_t time(time_t *t)
```
| **Parameter** | **Description** |
| ---------- | ------------------------------- |
|t |Time data pointer |
| **return** | —— |
| Current time value | |
Examples of use are as follows:
```c
time_t now; /* Save the current time value obtained */
/* Obtain Time */
now = time(RT_NULL);
/* Printout time information */
rt_kprintf("%s\n", ctime(&now));
```
>Currently only one RTC device is allowed in the system and the name is `"rtc"`.
## Functional Configuration
### Enable Soft RTC (Software Emulation RTC)
You can use the function of enabling RTC software emulation, which is ideal for products that do not require high time precision and have no hardware RTC. The configuration options of menuconfig are as follows:
```c
RT-Thread Components →
Device Drivers:
-*- Using RTC device drivers /* Use RTC device driver */
[ ] Using software simulation RTC device /* Use software simulation RTC device */
```
### Enable NTP Time Automatic Synchronization
If the RT-Thread is connected to the Internet, you can enable automatic NTP time synchronization to synchronize local time periodically.
First open the NTP function in menuconfig as follows:
```c
RT-Thread online packages →
IoT - internet of things →
netutils: Networking utilities for RT-Thread:
[*] Enable NTP(Network Time Protocol) client
```
After NTP is turned on, the RTC's automatic synchronization function will be automatically turned on, and the synchronization period and the delay time of the first synchronization can also be set:
```c
RT-Thread Components →
Device Drivers:
-*- Using RTC device drivers /* Use RTC device driver */
[ ] Using software simulation RTC device /* Use software simulation RTC device */
[*] Using NTP auto sync RTC time /* Automatically synchronize RTC time with NTP */
(30) NTP first sync delay time(second) for network connect /* The delay for performing NTP time synchronization for the first time. The purpose of the delay is to reserve a certain amount of time for the network connection and try to increase the success rate of the first NTP time synchronization. The default time is 30S； */
(3600) NTP auto sync period(second) /* NTP The synchronization period is automatically synchronized in seconds, and the default period is one hour (ie 3600S). */
```
## FinSH Command
Enter `date` to view the current time.
```c
msh />date
Fri Feb 16 01:11:56 2018
msh />
```
Also use the `date` command, after the command, enter `year` `month` `date` `hour ` ` minute ` ` second ` (between spaces, 24H system), and set the current time to 2018-02-16 01:15:30. The approximate effect is as follows:
```c
msh />date 2018 02 16 01 15 30
msh />
```
## RTC Device Usage Examples
For the specific usage of the RTC device, refer to the following example code. First, set the year, month, date, hour, minute and second information, and then delay the data for 3 seconds to get the current time information.
```c
/*
* Program listing: This is an RTC device usage routine
* The routine exports the rtc_sample command to the control terminal
* Command call format：rtc_sample
* Program function: Set the date and time of the RTC device. After a delay, obtain the current time and print the display.
*/
#include <rtthread.h>
#include <rtdevice.h>
static int rtc_sample(int argc, char *argv[])
{
rt_err_t ret = RT_EOK;
time_t now;
/* Set date */
ret = set_date(2018, 12, 3);
if (ret != RT_EOK)
{
rt_kprintf("set RTC date failed\n");
return ret;
}
/* Set time */
ret = set_time(11, 15, 50);
if (ret != RT_EOK)
{
rt_kprintf("set RTC time failed\n");
return ret;
}
/* Delay 3 seconds */
rt_thread_mdelay(3000);
/* Obtain Time */
now = time(RT_NULL);
rt_kprintf("%s\n", ctime(&now));
return ret;
}
/* Export to the msh command list */
MSH_CMD_EXPORT(rtc_sample, rtc sample);
```

465
documentation/device/sensor/sensor.md Normal file
View file

@ -0,0 +1,465 @@
# Sensor Device
## Introduction
Sensors are an important part of the Internet of Things, and sensors in an IoT system are equivalent to the eyes of humans. Without eyes, human beings can not see and interpret the world around them. The same is true for the Internet of Things.
Nowadays, with the development of IoT, a large number of sensors are available for developers to choose, such as Accelerometers, Magnetometers, Gyroscopes, Barometers/pressure senosrs, Hygrometers/humidity meters and so on. However, these sensors, manufactured by the world's leading semiconductor manufacturers, have increased market selectivity and made application development more difficult. Because different sensor manufacturers and sensors need their own unique drivers to run, developers need to write a device driver for each sensor, which can be difficult and time-consuming. In order to reduce the difficulty of application development and increase the reusability of sensor driver, we designed a Sensor device.
The function of the Sensor device is to provide a unified operation interface for the upper layer and improve the reusability of the upper code.
### Characteristics of the Sensor Device
- **Interface:** Standard device interface (open/close/read/control)
- **Work mode:** Supports polling, interrupts, three FIFO (First In, First Out) modes
- **Power mode:** support four modes: power failure, common, low power consumption and high power consumption
## Access Sensor Device
The application accesses the sensor device through the I/O device management interface provided by RT-Thread. The related interfaces are as follows:
| Functions | Description |
| --------------------------- | ------------------------------------------------------------ |
| rt_device_find() | Finding device handles based on device name of sensor device |
| rt_device_open() | open sensor device |
| rt_device_read() | read data |
| rt_device_control() | control sensor device |
| rt_device_set_rx_indicate() | setting reveive callback fuction |
| rt_device_close() | close sensor device |
### Find Sensor Device
The application obtains the device handle according to the name of the sensor device, and then can operate the sensor device. The function of finding the device is as follows:
```c
rt_device_t rt_device_find(const char* name);
```
| **Parameter** | **Description** |
| ------------- | ------------------------------------------------------------ |
| name | sensor device name |
| **return** | —— |
| handle | Finding the corresponding device returns the corresponding device handle |
| RT_NULL | No corresponding device object was found |
The use example is as follows:
```c
#define SENSOR_DEVICE_NAME "acce_st" /* sensor device name */
static rt_device_t sensor_dev; /* sensor device handle */
/* Find the sensor device according to the device name and get the device handle */
sensor_dev = rt_device_find(SENSOR_DEVICE_NAME);
```
### Open Sensor Device
Through the device handle, the application can open and close the device. When the device is opened, it will check whether the device has been initialized or not. If it is not initialized, it will call the initialization interface by default. Open the device through the following functions:
```c
rt_err_t rt_device_open(rt_device_t dev, rt_uint16_t oflags);
```
| **Parameter** | **Description** |
| ------------- | ------------------------------------------------------------ |
| dev | device handle |
| oflags | open mode flag |
| **Return** | —— |
| RT_EOK | open success |
| -RT_EBUSY | If the RT_DEVICE_FLAG_STANDALONE parameter is included in the parameter specified at the time of device registration, the device will not be allowed to open repeatedly. |
| -RT_EINVAL | Unsupported open mode |
| other err | open failed |
The oflags parameter supports the following parameters：
```c
#define RT_DEVICE_FLAG_RDONLY 0x001 /* Read-only mode for standard device, polling mode for corresponding sensors */
#define RT_DEVICE_FLAG_INT_RX 0x100 /* Interrupt Receiving Mode */
#define RT_DEVICE_FLAG_FIFO_RX 0x200 /* FIFO receiving mode */
```
There are three modes of receiving and sending sensor data: interrupt mode, polling mode and FIFO mode. When using these three modes, **only one of them can be chosen**. If the sensor's open parameter oflags does not specify the use of interrupt mode or FIFO mode, polling mode is used by default.
FIFO transmission mode needs sensor hardware support, data is stored in hardware FIFO, which reads and stores multiple data simultaneously, which allows the CPU to do other operations while gathering data. This feature is very useful in low power mode.
If the sensor uses FIFO receiving mode, the value of oflags is RT_DEVICE_FLAG_FIFO_RX.
An example of turning on sensor devices in polling mode is as follows:
```c
#define SAMPLE_SENSOR_NAME "acce_st" /* sensor device name */
int main(void)
{
rt_device_t dev;
struct rt_sensor_data data;
/* find sensor device */
dev = rt_device_find(SAMPLE_SENSOR_NAME);
/* Open sensor devices in read-only and polling mode */
rt_device_open(dev, RT_DEVICE_FLAG_RDWR);
if (rt_device_read(dev, 0, &data, 1) == 1)
{
rt_kprintf("acce: x:%5d, y:%5d, z:%5d, timestamp:%5d\n", data.data.acce.x, data.data.acce.y, data.data.acce.z, data.timestamp);
}
rt_device_close(dev);
return RT_EOK;
}
```
### Control Sensor Device
By command control words, the application program can configure the sensor device through the following functions:
```c
rt_err_t rt_device_control(rt_device_t dev, rt_uint8_t cmd, void* arg);
```
| **Parameter** | **Description** |
| ------------- | ------------------------------------------------------------ |
| dev | device handle |
| cmd | command control word, see below for more details. |
| arg | the parameters of command control word, see below for more details. |
| **Return** | —— |
| RT_EOK | success |
| -RT_ENOSYS | failed，device is NULL |
| other err | failed |
`cmd` currently supports the following command control words:
```c
#define RT_SEN_CTRL_GET_ID (0) /* read device ID */
#define RT_SEN_CTRL_GET_INFO (1) /* get device information */
#define RT_SEN_CTRL_SET_RANGE (2) /* Setting the measuring range of the sensor */
#define RT_SEN_CTRL_SET_ODR (3) /* Setting the Output Rate of Sensor Data，unit is HZ */
#define RT_SEN_CTRL_SET_MODE (4) /* Setting up working mode */
#define RT_SEN_CTRL_SET_POWER (5) /* Setting up power mode */
#define RT_SEN_CTRL_SELF_TEST (6) /* selfcheck */
```
#### Get device information
```c
struct rt_sensor_info info;
rt_device_control(dev, RT_SEN_CTRL_GET_INFO, &info);
LOG_I("vendor :%d", info.vendor);
LOG_I("model :%s", info.model);
LOG_I("unit :%d", info.unit);
LOG_I("intf_type :%d", info.intf_type);
LOG_I("period_min:%d", info.period_min);
```
#### Read Device ID
```c
rt_uint8_t reg = 0xFF;
rt_device_control(dev, RT_SEN_CTRL_GET_ID, &reg);
LOG_I("device id: 0x%x!", reg);
```
#### Setting the measuring range of the sensor
The unit that sets the measuring range of the sensor is the unit that is provided when the device is registered.
```c
rt_device_control(dev, RT_SEN_CTRL_SET_RANGE, (void *)1000);
```
#### Setting the Output Rate of Sensor Data
Set the output rate to 100Hz and call the following interface.
```c
rt_device_control(dev, RT_SEN_CTRL_SET_ODR, (void *)100);
```
#### Setting up working mode
```c
/* Set the working mode to polling mode */
rt_device_control(dev, RT_SEN_CTRL_SET_MODE, (void *)RT_SEN_MODE_POLLING);
/* Set working mode to interrupt mode */
rt_device_control(dev, RT_SEN_CTRL_SET_MODE, (void *)RT_SEN_MODE_INT);
/* Set working mode to FIFO mode */
rt_device_control(dev, RT_SEN_CTRL_SET_MODE, (void *)RT_SEN_MODE_FIFO);
```
#### Setting up power mode
```c
/* Set power mode to power-off mode */
rt_device_control(dev, RT_SEN_CTRL_SET_POWER, (void *)RT_SEN_POWER_DOWN);
/* Set power mode to normal mode */
rt_device_control(dev, RT_SEN_CTRL_SET_POWER, (void *)RT_SEN_POWER_NORMAL);
/* Setting Power Mode to Low Power Consumption Mode */
rt_device_control(dev, RT_SEN_CTRL_SET_POWER, (void *)RT_SEN_POWER_LOW);
/* Setting Power Mode to High Performance Mode */
rt_device_control(dev, RT_SEN_CTRL_SET_POWER, (void *)RT_SEN_POWER_HIGH);
```
#### Device self-inspection
```c
int test_res;
/* Control equipment self-check and return the results. Returning RT_EOK indicates success of self-check and other values indicate failure of self-check. */
rt_device_control(dev, RT_SEN_CTRL_SELF_TEST, &test_res);
```
### Setting Reveive Callback Fuction
Data reception instructions can be set by following functions. When the sensor receives data, it notifies the upper application thread that data arrives:
```c
rt_err_t rt_device_set_rx_indicate(rt_device_t dev, rt_err_t (*rx_ind)(rt_device_t dev,rt_size_t size));
```
| **Parameter** | **Description** |
| ------------- | --------------------------------------------- |
| dev | device handle |
| rx_ind | Callback function pointer |
| dev | device handle(parameter of callback function) |
| size | buffer size(parameter of callback function) |
| **Return** | —— |
| RT_EOK | Successful setup |
The callback function of the function is provided by the user. If the sensor is opened in interrupt mode, as the sensor receives data the callback function will be called. The data size of the buffer will be placed in the `size` parameter, and the sensor device handle will be placed in the `dev` parameter for users to obtain.
Generally, receiving callback function can send a semaphore or event to inform sensor data processing thread that data arrives. The use example is as follows:
```c
#define SAMPLE_SENSOR_NAME "acce_st" /* sensor device name */
static rt_device_t dev; /* sensoe device handle*/
static struct rt_semaphore rx_sem; /* The semaphore used to receive messages */
/* Callback function for receiving data */
static rt_err_t sensor_input(rt_device_t dev, rt_size_t size)
{
/* When the sensor receives the data, it generates an interrupt, calls the callback function, and sends the semphore . */
rt_sem_release(&rx_sem);
return RT_EOK;
}
static int sensor_sample(int argc, char *argv[])
{
dev = rt_device_find(SAMPLE_SENSOR_NAME);
/* Open Sensor Device in Interrupt Receive and Poll Send Mode */
rt_device_open(dev, RT_DEVICE_FLAG_INT_RX);
/* init semphore */
rt_sem_init(&rx_sem, "rx_sem", 0, RT_IPC_FLAG_FIFO);
/* setting reveive callback function */
rt_device_set_rx_indicate(dev, sensor_input);
}
```
### Read Data of Sensor Device
The following functions can be called to read the data received by the sensor:
```c
rt_size_t rt_device_read(rt_device_t dev, rt_off_t pos, void* buffer, rt_size_t size);
```
| **Parameter** | **Description** |
| ---------------------- | ------------------------------------------------------------ |
| dev | device handle |
| pos | Read data offset, sensor does not use this parameter |
| buffer | Buffer pointer, read data will be saved in the buffer |
| size | Size of read data |
| **Return** | —— |
| Real size of read data | Returns the number of read data |
| 0 | The errno of the current thread needs to be read to determine the error status |
The sensor uses the interrupt receiving mode and cooperates with the receiving callback function as follows:
```c
static rt_device_t dev; /* sensor device handle */
static struct rt_semaphore rx_sem; /* The semaphore used to receive messages */
/* Threads receiving data */
static void sensor_irq_rx_entry(void *parameter)
{
rt_device_t dev = parameter;
struct rt_sensor_data data;
rt_size_t res;
while (1)
{
rt_sem_take(rx_sem, RT_WAITING_FOREVER);
res = rt_device_read(dev, 0, &data, 1);
if (res == 1)
{
sensor_show_data(dev, &data);
}
}
}
```
The sensor uses FIFO receiving mode and cooperates with receiving callback function as follows:
```c
static rt_sem_t sensor_rx_sem = RT_NULL;
rt_err_t rx_cb(rt_device_t dev, rt_size_t size)
{
rt_sem_release(sensor_rx_sem);
return 0;
}
static void sensor_fifo_rx_entry(void *parameter)
{
rt_device_t dev = parameter;
struct rt_sensor_data data;
rt_size_t res, i;
data = rt_malloc(sizeof(struct rt_sensor_data) * 32);
while (1)
{
rt_sem_take(sensor_rx_sem, RT_WAITING_FOREVER);
res = rt_device_read(dev, 0, data, 32);
for (i = 0; i < res; i++)
{
sensor_show_data(dev, &data[i]);
}
}
}
int main(void)
{
static rt_thread_t tid1 = RT_NULL;
rt_device_t dev;
struct rt_sensor_data data;
sensor_rx_sem = rt_sem_create("sen_rx_sem", 0, RT_IPC_FLAG_FIFO);
tid1 = rt_thread_create("sen_rx_thread",
sensor_fifo_rx_entry, dev,
1024,
15, 5);
if (tid1 != RT_NULL)
rt_thread_startup(tid1);
dev = rt_device_find("acce_st");
rt_device_set_rx_indicate(dev, rx_cb);
rt_device_open(dev, RT_SEN_FLAG_FIFO);
return RT_EOK;
}
```
### Close Sensor Device
When the application completes the sensor operation, the sensor device can be closed by the following functions:
```c
rt_err_t rt_device_close(rt_device_t dev);
```
| **Parameter** | **Description** |
| ------------- | ------------------------------------------------------------ |
| dev | device handle |
| **Return** | —— |
| RT_EOK | The equipment was closed successfully. |
| -RT_ERROR | The device has been completely shut down and cannot be closed repeatedly. |
| other err | failed to close th device |
Closing the device interface and opening the device interface should be used in pairs, opening the primary device should close the primary device, so that the device will be completely closed, otherwise the device is still in an open state.
## Example Code for Sensor Device
The specific use of sensor devices can be referred to the following sample code, the main steps of the sample code are as follows:
1. Find the sensor device first and get the device handle.
2. Open the sensor device by polling.
3. Read the data five times in a row and print it out.
4. Close the sensor device.
This sample code is not limited to a specific BSP. According to the BSP registered sensor device, input different dev_name to run.
```c
/*
* Program List: This is a routine for sensor devices
* The routine exports the sensor_sample command to the control terminal
* Command Call Format：sensor_sample dev_name
* Command Interpretation: The second parameter of the command is the name of the sensor device to be used.
* Program function: Open the corresponding sensor, and then read the data five times in a row and print it out.
*/
#include "sensor.h"
static void sensor_show_data(rt_size_t num, rt_sensor_t sensor, struct rt_sensor_data *sensor_data)
{
switch (sensor->info.type)
{
case RT_SENSOR_CLASS_ACCE:
rt_kprintf("num:%3d, x:%5d, y:%5d, z:%5d, timestamp:%5d\n", num, sensor_data->data.acce.x, sensor_data->data.acce.y, sensor_data->data.acce.z, sensor_data->timestamp);
break;
case RT_SENSOR_CLASS_GYRO:
rt_kprintf("num:%3d, x:%8d, y:%8d, z:%8d, timestamp:%5d\n", num, sensor_data->data.gyro.x, sensor_data->data.gyro.y, sensor_data->data.gyro.z, sensor_data->timestamp);
break;
case RT_SENSOR_CLASS_MAG:
rt_kprintf("num:%3d, x:%5d, y:%5d, z:%5d, timestamp:%5d\n", num, sensor_data->data.mag.x, sensor_data->data.mag.y, sensor_data->data.mag.z, sensor_data->timestamp);
break;
case RT_SENSOR_CLASS_HUMI:
rt_kprintf("num:%3d, humi:%3d.%d%%, timestamp:%5d\n", num, sensor_data->data.humi / 10, sensor_data->data.humi % 10, sensor_data->timestamp);
break;
case RT_SENSOR_CLASS_TEMP:
rt_kprintf("num:%3d, temp:%3d.%dC, timestamp:%5d\n", num, sensor_data->data.temp / 10, sensor_data->data.temp % 10, sensor_data->timestamp);
break;
case RT_SENSOR_CLASS_BARO:
rt_kprintf("num:%3d, press:%5d, timestamp:%5d\n", num, sensor_data->data.baro, sensor_data->timestamp);
break;
case RT_SENSOR_CLASS_STEP:
rt_kprintf("num:%3d, step:%5d, timestamp:%5d\n", num, sensor_data->data.step, sensor_data->timestamp);
break;
default:
break;
}
}
static void sensor_sample(int argc, char **argv)
{
rt_device_t dev = RT_NULL;
struct rt_sensor_data data;
rt_size_t res, i;
/* Finding Sensor Devices in the System */
dev = rt_device_find(argv[1]);
if (dev == RT_NULL)
{
rt_kprintf("Can't find device:%s\n", argv[1]);
return;
}
/* Open sensor devices in polling mode */
if (rt_device_open(dev, RT_DEVICE_FLAG_RDWR) != RT_EOK)
{
rt_kprintf("open device failed!");
return;
}
for (i = 0; i < 5; i++)
{
/* Read a data from a sensor */
res = rt_device_read(dev, 0, &data, 1);
if (res != 1)
{
rt_kprintf("read data failed!size is %d", res);
}
else
{
sensor_show_data(i, (rt_sensor_t)dev, &data);
}
rt_thread_mdelay(100);
}
/* Close the sensor device */
rt_device_close(dev);
}
MSH_CMD_EXPORT(sensor_sample, sensor device sample);
```

BIN
documentation/device/spi/figures/spi1.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 7.9 KiB

BIN
documentation/device/spi/figures/spi2.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 9.8 KiB

BIN
documentation/device/spi/figures/spi5.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 46 KiB

741
documentation/device/spi/spi.md Normal file
View file

@ -0,0 +1,741 @@
# SPI Device
## Introduction to SPI
SPI (Serial Peripheral Interface) is a high-speed, full-duplex, synchronous communication bus commonly used for short-range communication. It is mainly used in EEPROM, FLASH, real-time clock, AD converter, and digital signal processing and between the device and the digital signal decoder. SPI generally uses 4 lines of communication, as shown in the following figure:
![Ways of communication from SPI Master to SPI Slave](figures/spi1.png)
* MOSI :SPI Bus Master Output/Slave Input.
* MISO :SPI Bus Master Input/Slave Output.
* SCLK :Serial Clock, Master device outputs clock signal to slave device.
* CS : select the slave device, also called SS, CSB, CSN, EN, etc., the master device outputs a chip select signal to the slave device.
The SPI works in master-slave mode and usually has one master and one or more slaves. The communication is initiated by the master device. The master device selects the slave device to communicate through CS, and then provides a clock signal to the slave device through SCLK. The data is output to the slave device through the MOSI, and the data sent by the slave device is received through the MISO.
As shown in the figure below, the chip has two SPI controllers. The SPI controller corresponds to the SPI master. Each SPI controller can connect multiple SPI slaves. The slave devices mounted on the same SPI controller share three signal pins: SCK, MISO, MOSI, but the CS pins of each slave device are independent.
![Connect from one SPI controller to multiple SPI slaves](figures/spi2.png)
The master device selects the slave device by controlling the CS pin, typically active low. Only one CS pin is active on an SPI master, and the slave connected to the active CS pin can now communicate with the master.
The slave's clock is provided by the master through SCLK, and MOSI and MISO complete the data transfer based on SCLK. The working timing mode of the SPI is determined by the phase relationship between CPOL (Clock Polarity) and CPHA (Clock Phase). CPOL represents the state of the initial level of the clock signal. A value of 0 indicates that the initial state of the clock signal is low, and a value of 1 indicates that the initial level of the clock signal is high. CPHA indicates on which clock edge the data is sampled. A value of 0 indicates that the data is sampled on the first clock change edge, and a value of 1 indicates that the data is sampled on the second clock change edge. There are 4 working timing modes according to different combinations of CPOL and CPHA: ①CPOL=0, CPHA=0; ②CPOL=0, CPHA=1; ③CPOL=1, CPHA=0; ④CPOL=1, CPHA=1. As shown below:
![4 working timing modes of SPI](figures/spi5.png)
**QSPI:** QSPI is short for Queued SPI and is an extension of the SPI interface from Motorola, which is more extensive than SPI applications. Based on the SPI protocol, Motorola has enhanced its functionality, added a queue transfer mechanism, and introduced a queue serial peripheral interface protocol (QSPI protocol). Using this interface, users can transfer transmission queues containing up to 16 8-bit or 16-bit data at one time. Once the transfer is initiated, CPU is not required until the end of the transfer, greatly improving the transfer efficiency. Compared to SPI, the biggest structural feature of QSPI is the replacement of the transmit and receive data registers of the SPI with 80 bytes of RAM.
**Dual SPI Flash:** For SPI Flash, full-duplex is not commonly used. You can send a command byte into Dual mode and let it work in half-duplex mode to double data transfer. Thus, MOSI becomes SIO0 (serial io 0), and MISO becomes SIO1 (serial io 1), so that 2 bit data can be transmitted in one clock cycle, which doubles the data transmission.
**Quad SPI Flash:** Similar to the Dual SPI, Quad SPI Flash adds two I/O lines (SIO2, SIO3) to transfer 4 bits of data in one clock.
So for SPI Flash, there are three types of standard SPI Flash, Dual SPI Flash, Quad SPI Flash. At the same clock, the higher the number of lines, the higher the transmission rate.
## Mount SPI Device
The SPI driver registers the SPI bus and the SPI device needs to be mounted to the SPI bus that has already been registered.
```C
rt_err_t rt_spi_bus_attach_device(struct rt_spi_device *device,
const char *name,
const char *bus_name,
void *user_data)
```
| **Parameter** | Description |
| -------- | ---------------------------------- |
| device | SPI device handle |
| name | SPI device name |
| bus_name | SPI bus name |
| user_data | user data pointer |
| **Return** | —— |
| RT_EOK | Success |
| Other Errors | Failure |
This function is used to mount an SPI device to the specified SPI bus, register the SPI device with the kernel, and save user_data to the control block of the SPI device.
The general SPI bus naming principle is spix, and the SPI device naming principle is spixy. For example, spi10 means device 0 mounted on the spi1 bus. User_data is generally the CS pin pointer of the SPI device. When data is transferred, the SPI controller will operate this pin for chip select.
If you use the BSP in the `rt-thread/bsp/stm32` directory, you can use the following function to mount the SPI device to the bus:
```c
rt_err_t rt_hw_spi_device_attach(const char *bus_name, const char *device_name, GPIO_TypeDef* cs_gpiox, uint16_t cs_gpio_pin);
```
The following sample code mounts the SPI FLASH W25Q128 to the SPI bus:
```c
static int rt_hw_spi_flash_init(void)
{
__HAL_RCC_GPIOB_CLK_ENABLE();
rt_hw_spi_device_attach("spi1", "spi10", GPIOB, GPIO_PIN_14);
if (RT_NULL == rt_sfud_flash_probe("W25Q128", "spi10"))
{
return -RT_ERROR;
};
return RT_EOK;
}
/* Export to automatic initialization */
INIT_COMPONENT_EXPORT(rt_hw_spi_flash_init);
```
## Configuring SPI Device
The SPI device's transmission parameters need to be configured after the SPI device is mounted to the SPI bus.
```c
rt_err_t rt_spi_configure(struct rt_spi_device *device,
struct rt_spi_configuration *cfg)
```
| **Parameter** | **Description** |
| -------- | ---------------------------------- |
| device | SPI device handle |
| cfg | SPI configuration parameter pointer |
| **Return** | —— |
| RT_EOK | Success |
This function saves the configuration parameters pointed to by `cfg` to the control block of the SPI device device, which is used when transferring data.
The `struct rt_spi_configuration` prototype is as follows:
```c
struct rt_spi_configuration
{
rt_uint8_t mode; /* mode */
rt_uint8_t data_width; /* data width, 8 bits, 16 bits, 32 bits */
rt_uint16_t reserved; /* reserved */
rt_uint32_t max_hz; /* maximum frequency */
};
```
**Mode: **Contains MSB/LSB, master-slave mode, timing mode, etc. The available macro combinations are as follows:
```c
/* Set the data transmission order whether the MSB bit is first or the LSB bit is before */
#define RT_SPI_LSB (0<<2) /* bit[2]: 0-LSB */
#define RT_SPI_MSB (1<<2) /* bit[2]: 1-MSB */
/* Set the master-slave mode of the SPI */
#define RT_SPI_MASTER (0<<3) /* SPI master device */
#define RT_SPI_SLAVE (1<<3) /* SPI slave device */
/* Set clock polarity and clock phase */
#define RT_SPI_MODE_0 (0 | 0) /* CPOL = 0, CPHA = 0 */
#define RT_SPI_MODE_1 (0 | RT_SPI_CPHA) /* CPOL = 0, CPHA = 1 */
#define RT_SPI_MODE_2 (RT_SPI_CPOL | 0) /* CPOL = 1, CPHA = 0 */
#define RT_SPI_MODE_3 (RT_SPI_CPOL | RT_SPI_CPHA) /* CPOL = 1, CPHA = 1 */
#define RT_SPI_CS_HIGH (1<<4) /* Chipselect active high */
#define RT_SPI_NO_CS (1<<5) /* No chipselect */
#define RT_SPI_3WIRE (1<<6) /* SI/SO pin shared */
#define RT_SPI_READY (1<<7) /* Slave pulls low to pause */
```
**Data width:** The data width format that can be sent and received by the SPI master and SPI slaves is set to 8-bit, 16-bit or 32-bit.
**Maximum Frequency：** Set the baud rate for data transfer, also based on the baud rate range at which the SPI master and SPI slaves operate.
The example for configuration is as follows:
```c
struct rt_spi_configuration cfg;
cfg.data_width = 8;
cfg.mode = RT_SPI_MASTER | RT_SPI_MODE_0 | RT_SPI_MSB;
cfg.max_hz = 20 * 1000 *1000; /* 20M */
rt_spi_configure(spi_dev, &cfg);
```
## QSPI Configuration
To configure the transmission parameters of a QSPI device, use the following function:
```c
rt_err_t rt_qspi_configure(struct rt_qspi_device *device, struct rt_qspi_configuration *cfg);
```
| **Parameter** | **Description** |
| -------- | ---------------------------------- |
| device | QSPI device handle |
| cfg | QSPI configuration parameter pointer |
| **Return** | —— |
| RT_EOK | Success |
This function saves the configuration parameters pointed to by `cfg` to the control block of the QSPI device, which is used when transferring data.
The `struct rt_qspi_configuration` prototype is as follows:
```c
struct rt_qspi_configuration
{
struct rt_spi_configuration parent; /* SPI device configuration parent */
rt_uint32_t medium_size; /* medium size */
rt_uint8_t ddr_mode; /* double rate mode */
rt_uint8_t qspi_dl_width ; /* QSPI bus width, single line mode 1 bit, 2 line mode 2 bits, 4 line mode 4 bits */
};
```
## Access SPI Device
In general, the MCU's SPI device communicates as a master and slave. In the RT-Thread, the SPI master is virtualized as an SPI bus device. The application uses the SPI device management interface to access the SPI slave device. The main interfaces are as follows:
| **Function** | **Description** |
| -------------------- | ---------------------------------- |
| rt_device_find() | Find device handles based on SPI device name |
| rt_spi_transfer_message() | Custom transfer data |
| rt_spi_transfer() | Transfer data once |
| rt_spi_send() | Send data once |
| rt_spi_recv() | Receive data one |
| rt_spi_send_then_send() | Send data twice |
| rt_spi_send_then_recv() | Send then Receive |
>The SPI data transfer related interface will call rt_mutex_take(). This function cannot be called in the interrupt service routine, which will cause the assertion to report an error.
### Find SPI Device
Before using the SPI device, you need to find and obtain the device handle according to the SPI device name, so that you can operate the SPI device. The device function is as follows.
```c
rt_device_t rt_device_find(const char* name);
```
| **Parameter** | **Description** |
| ------------- | ------------------------------------------------------------ |
| name | Device name |
| **Return** | —— |
| device handle | Finding the corresponding device will return the corresponding device handle |
| RT_NULL | Corresponding device object unfound |
In general, the name of the SPI device registered to the system is spi10, qspi10, etc. The usage examples are as follows:
```c
#define W25Q_SPI_DEVICE_NAME "qspi10" /* SPI device name */
struct rt_spi_device *spi_dev_w25q; /* SPI device handle */
/* Find the spi device to get the device handle */
spi_dev_w25q = (struct rt_spi_device *)rt_device_find(W25Q_SPI_DEVICE_NAME);
```
### Transfer Custom Data
By obtaining the SPI device handle, the SPI device management interface can be used to access the SPI device device for data transmission and reception. You can transfer messages by the following function:
```c
struct rt_spi_message *rt_spi_transfer_message(struct rt_spi_device *device,struct rt_spi_message *message)；
```
| **Parameter** | **Description** |
| ---------------- | ------------------------------------------------------------ |
| device | SPI device handle |
| message | message pointer |
| **Return** | —— |
| RT_NULL | Send successful |
| Non-null pointer | Send failed, return a pointer to the remaining unsent message |
This function can transmit a series of messages, the user can customize the value of each parameter of the message structure to be transmitted, so that the data transmission mode can be conveniently controlled. The `struct rt_spi_message` prototype is as follows:
```c
struct rt_spi_message
{
const void *send_buf; /* Send buffer pointer */
void *recv_buf; /* Receive buffer pointer */
rt_size_t length; /* Send/receive data bytes */
struct rt_spi_message *next; /* Pointer to the next message to continue sending */
unsigned cs_take : 1; /* Take chip selection*/
unsigned cs_release : 1; /* Release chip selection */
};
```
send_buf :sendbuf is the send buffer pointer. When the value is RT_NULL, it means that the current transmission is only receiving state, and no data needs to be sent.
recv_buf :recvbuf is the receive buffer pointer. When the value is RT_NULL, it means that the current transmission is in the transmit-only state. It does not need to save the received data, so the received data is directly discarded.
length :The unit of length is word, that is, when the data length is 8 bits, each length occupies 1 byte; when the data length is 16 bits, each length occupies 2 bytes.
next :The parameter next is a pointer to the next message to continue to send. If only one message is sent, the value of this pointer is RT_NULL. Multiple messages to be transmitted are connected together in a singly linked list by the next pointer.
cs_take :A cs_take value of 1 means that the corresponding CS is set to a valid state before data is transferred.
cs_release :A cs_release value of 1 indicates that the corresponding CS is released after the data transfer ends.
>When send_buf or recv_buf is not empty, the available size for both cannot be less than length.
If you use this function to transfer messages, the first message sent by cs_take needs to be set to 1. Set the chip to be valid, and the cs_release of the last message needs to be set to 1. Release the chip select.
An example of use is as follows:
```c
#define W25Q_SPI_DEVICE_NAME "qspi10" /* SPI device name */
struct rt_spi_device *spi_dev_w25q; /* SPI device handle */
struct rt_spi_message msg1, msg2;
rt_uint8_t w25x_read_id = 0x90; /* command */
rt_uint8_t id[5] = {0};
/* Find the spi device to get the device handle */
spi_dev_w25q = (struct rt_spi_device *)rt_device_find(W25Q_SPI_DEVICE_NAME);
/* Send command to read ID */
struct rt_spi_message msg1, msg2;
msg1.send_buf = &w25x_read_id;
msg1.recv_buf = RT_NULL;
msg1.length = 1;
msg1.cs_take = 1;
msg1.cs_release = 0;
msg1.next = &msg2;
msg2.send_buf = RT_NULL;
msg2.recv_buf = id;
msg2.length = 5;
msg2.cs_take = 0;
msg2.cs_release = 1;
msg2.next = RT_NULL;
rt_spi_transfer_message(spi_dev_w25q, &msg1);
rt_kprintf("use rt_spi_transfer_message() read w25q ID is:%x%x\n", id[3], id[4]);
```
### Transfer Data Once
If only transfer data for once, use the following function:
```c
rt_size_t rt_spi_transfer(struct rt_spi_device *device,
const void *send_buf,
void *recv_buf,
rt_size_t length);
```
| **Parameter** | **Description** |
|----------|----------------------|
| device | SPI device handle |
| send_buf | Send data buffer pointer |
| recv_buf | Receive data buffer pointer |
| length | Length of data send/received |
| **Return** | —— |
| 0 | Transmission failed |
| Non-0 Value | Length of data successfully transferred |
This function is equivalent to calling `rt_spi_transfer_message()` to transfer a message. When starting to send data, the chip is selected. When the function returns, the chip is released. The message parameter is configured as follows:
```c
struct rt_spi_message msg；
msg.send_buf = send_buf;
msg.recv_buf = recv_buf;
msg.length = length;
msg.cs_take = 1;
msg.cs_release = 1;
msg.next = RT_NULL;
```
### Send Data Once
If only send data once and ignore the received data, use the following function:
```c
rt_size_t rt_spi_send(struct rt_spi_device *device,
const void *send_buf,
rt_size_t length)
```
| **Parameter** | **Description** |
|----------|--------------------|
| device | SPI device handle |
| send_buf | Send data buffer pointer |
| length | Length of data sent |
| **Return** | —— |
| 0 | Transmission failed |
| Non-0 Value | Length of data successfully transferred |
Call this function to send the data of the buffer pointed to by send_buf, ignoring the received data. This function is a wrapper of the `rt_spi_transfer()` function.
This function is equivalent to calling `rt_spi_transfer_message()` to transfer a message. When the data starts to be sent, the chip is selected. When the function returns, the chip is released. The message parameter is configured as follows:
```c
struct rt_spi_message msg；
msg.send_buf = send_buf;
msg.recv_buf = RT_NULL;
msg.length = length;
msg.cs_take = 1;
msg.cs_release = 1;
msg.next = RT_NULL;
```
### Receive Data Once
If only receive data once, use the following function:
```c
rt_size_t rt_spi_recv(struct rt_spi_device *device,
void *recv_buf,
rt_size_t length);
```
| **Parameter** | **Description** |
|----------|--------------------|
| device | SPI device handle |
| recv_buf | Send data buffer pointer |
| length | Length of data sent |
| **Return** | —— |
| 0 | Transmission failed |
| Non-0 Value | Length of data successfully transferred |
Call this function to receive the data and save it to the buffer pointed to by recv_buf. This function is a wrapper of the `rt_spi_transfer()` function. The SPI bus protocol stipulates that the master can only generate a clock, so when receiving data, the master will send the data 0XFF.
This function is equivalent to calling `rt_spi_transfer_message()` to transfer a message. When receiving data, the chip is selected. When the function returns, the chip is released. The message parameter is configured as follows:
```c
struct rt_spi_message msg；
msg.send_buf = RT_NULL;
msg.recv_buf = recv_buf;
msg.length = length;
msg.cs_take = 1;
msg.cs_release = 1;
msg.next = RT_NULL;
```
### Send Data Twice in Succession
If need to send data of 2 buffers in succession and the CS is not released within the process, you can call the following function:
```c
rt_err_t rt_spi_send_then_send(struct rt_spi_device *device,
const void *send_buf1,
rt_size_t send_length1,
const void *send_buf2,
rt_size_t send_length2);
```
| **Parameter** | **Description** |
|--------------|---------------------------|
| device | SPI device handle |
| send_buf1 | Send data buffer pointer 1 |
| send_length1 | Send data buffer length 1 |
| send_buf2 | Send data buffer pointer 2 |
| send_length2 | Send data buffer length 2 |
| **Return** | —— |
| RT_EOK | Send Successful |
| -RT_EIO | Send Failed |
This function can continuously send data of 2 buffers, ignore the received data, select the CS when send_buf1 is sent, and release the CS after sending send_buf2.
This function is suitable for writing a piece of data to the SPI device, sending data such as commands and addresses for the first time, and sending data of the specified length for the second time. The reason is that it is sent twice instead of being merged into one data block, or `rt_spi_send()`is called twice, because in most data write operations, commands and addresses need to be sent first, and the length is usually only a few bytes. If send it in conjunction with the data that follows, it will need a memory space request and a lot of data handling. If `rt_spi_send()`is called twice, the chip select will be released after the command and address are sent. Most SPI devices rely on setting the chip select once to be the start of the command, so the chip selects the command or address after sending. After the data is released, the operation is discarded.
This function is equivalent to calling `rt_spi_transfer_message()` to transfer 2 messages. The message parameter is configured as follows:
```c
struct rt_spi_message msg1,msg2；
msg1.send_buf = send_buf1;
msg1.recv_buf = RT_NULL;
msg1.length = send_length1;
msg1.cs_take = 1;
msg1.cs_release = 0;
msg1.next = &msg2;
msg2.send_buf = send_buf2;
msg2.recv_buf = RT_NULL;
msg2.length = send_length2;
msg2.cs_take = 0;
msg2.cs_release = 1;
msg2.next = RT_NULL;
```
### Receive Data After Sending Data
If need to send data to the slave device first, then receive the data sent from the slave device, and the CS is not released within the process, call the following function to implement:
```c
rt_err_t rt_spi_send_then_recv(struct rt_spi_device *device,
const void *send_buf,
rt_size_t send_length,
void *recv_buf,
rt_size_t recv_length);
```
| **Parameter** | **Description** |
|-------------|--------------------------|
| device | SPI slave device handle |
| send_buf | Send data buffer pointer |
| send_length | Send data buffer length |
| recv_buf | Receive data buffer pointer |
| recv_length | Receive data buffer length |
| **Return** | —— |
| RT_EOK | Successful |
| -RT_EIO | Failed |
This function select CS when sending the first data send_buf when the received data is ignored, and the second data is sent. At this time, the master device will send the data 0XFF, and the received data will be saved in recv_buf, and CS will be released when the function returns.
This function is suitable for reading a piece of data from the SPI slave device. The first time it will send some command and address data, and then receive the data of the specified length.
This function is equivalent to calling `rt_spi_transfer_message()` to transfer 2 messages. The message parameter is configured as follows:
```c
struct rt_spi_message msg1,msg2；
msg1.send_buf = send_buf;
msg1.recv_buf = RT_NULL;
msg1.length = send_length;
msg1.cs_take = 1;
msg1.cs_release = 0;
msg1.next = &msg2;
msg2.send_buf = RT_NULL;
msg2.recv_buf = recv_buf;
msg2.length = recv_length;
msg2.cs_take = 0;
msg2.cs_release = 1;
msg2.next = RT_NULL;
```
The SPI device management module also provides `rt_spi_sendrecv8()` and `rt_spi_sendrecv16()` functions, both are wrapper of the `rt_spi_send_then_recv()`. `rt_spi_sendrecv8()` sends a byte data and receives one byte data, and`rt_spi_sendrecv16()` sends 2 bytes. The section data receives 2 bytes of data at the same time.
## Access QSPI Device
The data transfer interface of QSPI is as follows:
| **P**arameter | **Description** |
| -------------------- | ----------------------------|
| rt_qspi_transfer_message() | Transfer message |
| rt_qspi_send_then_recv() | Send then receive |
| rt_qspi_send() | Send data once |
>The QSPI data transfer related interface will call rt_mutex_take(). This function cannot be called in the interrupt service routine, which will cause the assertion to report an error.
### Transfer Data
Transfer messages by the following function:
```c
rt_size_t rt_qspi_transfer_message(struct rt_qspi_device *device, struct rt_qspi_message *message);
```
| **Parameter** | **Description** |
|----------|--------------------------------------------|
| device | QSPI device handle |
| message | Message pointer |
| **Return** | —— |
| Actual transmitted message size | |
The message `structure struct rt_qspi_message` prototype is as follows:
```c
struct rt_qspi_message
{
struct rt_spi_message parent; /* inhert from struct rt_spi_message */
struct
{
rt_uint8_t content; /* Instruction content */
rt_uint8_t qspi_lines; /* Instruction mode, single line mode 1 bit, 2 line mode 2 bits, 4 line mode 4 bits */
} instruction; /* Instruction phase */
struct
{
rt_uint32_t content; /* Address/alternate byte content */
rt_uint8_t size; /* Address/alternate byte size */
rt_uint8_t qspi_lines; /* Address/alternate byte mode, single line mode 1 bit, 2 line mode 2 bits, 4 line mode 4 bits */
} address, alternate_bytes; /* Address/alternate byte stage */
rt_uint32_t dummy_cycles; /* Dummy cycle */
rt_uint8_t qspi_data_lines; /* QSPI data line */
};
```
### Receive Data
Use the following function to receive data:
```c
rt_err_t rt_qspi_send_then_recv(struct rt_qspi_device *device,
const void *send_buf,
rt_size_t send_length,
void *recv_buf,
rt_size_t recv_length);
```
| **Parameter** | **Description** |
|-------------|--------------------------|
| device | QSPI device handle |
| send_buf | Send data buffer pointer |
| send_length | Send data length |
| recv_buf | Receive data buffer pointer |
| recv_length | Receive data length |
| **Return** | —— |
| RT_EOK | Successful |
| Other Errors | Failed |
The send_buf parameter contains the sequence of commands that will be sent.
### Send Data
```c
rt_err_t rt_qspi_send(struct rt_qspi_device *device, const void *send_buf, rt_size_t length)
```
| **Parameter** | **Description** |
|-------------|--------------------------|
| device | QSPI device handle |
| send_buf | Send data buffer pointer |
| length | Send data length |
| **Return** | —— |
| RT_EOK | Successful |
| Other Errors | Failed |
The send_buf parameter contains the sequence of commands and data to be sent.
## Special Usage Scenarios
In some special usage scenarios, a device wants to monopolize the bus for a period of time, and the CS is always valid during the period, during which the data transmission may be intermittent, then the relevant interface can be used as shown. The transfer data function must use `rt_spi_transfer_message()`, and this function must set the cs_take and cs_release of the message to be transmitted to 0 value, because the CS has already used other interface control, and does not need to control during data transmission.
### Acquire the SPI bus
In the case of multi-threading, the same SPI bus may be used in different threads. In order to prevent the data being transmitted by the SPI bus from being lost, the slave device needs to acquire the right to use the SPI bus before starting to transfer data. To transfer data using the bus, use the following function to acquire the SPI bus:
```c
rt_err_t rt_spi_take_bus(struct rt_spi_device *device);
```
| **Parameter** | **Description** |
|----------|---------------|
| device | SPI device handle |
| **Return** | —— |
| RT_EOK | Successful |
| Other Errors | Failed |
### Select CS
After obtaining the usage right of the bus from the device, you need to set the corresponding chip selection signal to be valid. You can use the following function to select the CS:
```c
rt_err_t rt_spi_take(struct rt_spi_device *device)；
```
| **Parameter** | **Description** |
|----------|---------------|
| device | SPI device handle |
| **Return** | —— |
| 0 | Successful |
| Other Errors | Failed |
### Add a New Message
When using `rt_spi_transfer_message()` to transfer messages, all messages to be transmitted are connected in the form of a singly linked list. Use the following function to add a new message to be sent to the message list:
```c
void rt_spi_message_append(struct rt_spi_message *list,
struct rt_spi_message *message);
```
| **Parameter** | **Description** |
| ------------- | ----------------------------------- |
| list | Message link node to be transmitted |
| message | New message pointer |
### Release CS
After the device data transfer is completed, CS need to be released. Use the following function to release the CS:
```c
rt_err_t rt_spi_release(struct rt_spi_device *device)；
```
| **Parameter** | **D**escription |
|----------|---------------|
| device | SPI device handle |
| Return | —— |
| 0 | Successful |
| Other Errors | Failed |
### Release Data Bus
The slave device does not use the SPI bus to transfer data. The bus must be released as soon as possible so that other slave devices can use the SPI bus to transfer data. The following function can be used to release the bus:
```c
rt_err_t rt_spi_release_bus(struct rt_spi_device *device);
```
| **Parameter** | **Description** |
|----------|---------------|
| device | SPI device handle |
| **Return** | —— |
| RT_EOK | Successful |
## SPI Device Usage Example
The specific use of the SPI device can be referred to the following sample code. The sample code first finds the SPI device to get the device handle, and then uses the rt_spi_transfer_message() send command to read the ID information.
```c
/*
* Program listing: This is a SPI device usage routine
* The routine exports the spi_w25q_sample command to the control terminal
* Command call format: spi_w25q_sample spi10
* Command explanation: The second parameter of the command is the name of the SPI device to be used. If it is empty, the default SPI device is used.
* Program function: read w25q ID data through SPI device
*/
#include <rtthread.h>
#include <rtdevice.h>
#define W25Q_SPI_DEVICE_NAME "qspi10"
static void spi_w25q_sample(int argc, char *argv[])
{
struct rt_spi_device *spi_dev_w25q;
char name[RT_NAME_MAX];
rt_uint8_t w25x_read_id = 0x90;
rt_uint8_t id[5] = {0};
if (argc == 2)
{
rt_strncpy(name, argv[1], RT_NAME_MAX);
}
else
{
rt_strncpy(name, W25Q_SPI_DEVICE_NAME, RT_NAME_MAX);
}
/* Find the spi device to get the device handle */
spi_dev_w25q = (struct rt_spi_device *)rt_device_find(name);
if (!spi_dev_w25q)
{
rt_kprintf("spi sample run failed! can't find %s device!\n", name);
}
else
{
/* Method 1: Send the command to read the ID using rt_spi_send_then_recv() */
rt_spi_send_then_recv(spi_dev_w25q, &w25x_read_id, 1, id, 5);
rt_kprintf("use rt_spi_send_then_recv() read w25q ID is:%x%x\n", id[3], id[4]);
/* Method 2: Send the command to read the ID using rt_spi_transfer_message() */
struct rt_spi_message msg1, msg2;
msg1.send_buf = &w25x_read_id;
msg1.recv_buf = RT_NULL;
msg1.length = 1;
msg1.cs_take = 1;
msg1.cs_release = 0;
msg1.next = &msg2;
msg2.send_buf = RT_NULL;
msg2.recv_buf = id;
msg2.length = 5;
msg2.cs_take = 0;
msg2.cs_release = 1;
msg2.next = RT_NULL;
rt_spi_transfer_message(spi_dev_w25q, &msg1);
rt_kprintf("use rt_spi_transfer_message() read w25q ID is:%x%x\n", id[3], id[4]);
}
}
/* Export to the msh command list */
MSH_CMD_EXPORT(spi_w25q_sample, spi w25q sample);
```

BIN
documentation/device/uart/figures/uart-dma.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 39 KiB

BIN
documentation/device/uart/figures/uart-int.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 40 KiB

BIN
documentation/device/uart/figures/uart1.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 3.3 KiB

646
documentation/device/uart/uart.md Normal file
View file

@ -0,0 +1,646 @@
# UART Device
## UART Introduction
UART (Universal Asynchronous Receiver/Transmitter), as a kind of asynchronous serial communication protocol, the working principle is to transmit each character of the transmitted data one by one. It is the most frequently used data bus during application development.
The UART serial port is characterized by sequentially transmitting data one bit at a time. As long as two transmission lines can realize two-way communication, one line transmits data while the other receives data . There are several important functions for UART serial communication, namely baud rate, start bit, data bit, stop bit and parity bit. For two ports that use UART serial port communication, these functions must be matched, otherwise the communication can't be carried out normally. The data format of the UART serial port transmission is as shown below:
![Serial Transmission Data Format](figures/uart1.png)
* Start bit: Indicates the start of data transfer and the level logic is "0".
- Data bits: Possible values are 5, 6, 7, 8, and 9, indicating that these bits are transmitted. The value is generally 8, because an ASCII character value is 8 bits.
- Parity check bit: It it used by the receiver to verify the received data. The number of bits is used in the check of "1" is even (even parity) or odd (odd parity) ,in order to verify the data transmission. It is also fine by not using this bit .
- Stop Bit: Indicates the end of one frame of data. The level logic is "1".
- Baudrate: It is the rate at which a serial port communicates, which expressed in bits per second (bps) of the binary code transmitted in unit time. The common baud rate values are 4800, 9600, 14400, 38400, 115200, etc. The higher the value is, the faster the data transmission will be.
## Access UART Device
The application accesses the serial port hardware through the I/O device management interface provided by RT-Thread. The related interfaces are as follows:
| **Funtion** | **Description** |
| --------------------------- | -------------------------- |
| rt_device_find() | find device |
| rt_device_open() | open device |
| rt_device_read() | read device |
| rt_device_write() |write device|
| rt_device_control() | control device |
| rt_device_set_rx_indicate() | set receive callback function |
| rt_device_set_tx_complete() | set send complete callback function |
| rt_device_close() | close device |
### Find UART Device
The application obtains the device handle according to the uart device name, and then can operate the uart device.The device find function is shown below
```c
rt_device_t rt_device_find(const char* name);
```
| **Parameter** | **Description** |
| ------------- | ------------------------------------------------------------ |
| name | device's name |
| **back** | —— |
| device handle | finding the corresponding device will return to the corresponding device handle |
| RT_NULL | corresponding device object was not found |
Generally, the name of the uart device registered to the system is uart0, uart1, etc. samples are as follows:
```c
#define SAMPLE_UART_NAME "uart2" /* uart device name */
static rt_device_t serial; /* uart device handle */
/* Find uart device*/
serial = rt_device_find(SAMPLE_UART_NAME);
```
### Open UART Device
Through the device handle, the application can open and close the device. When the device is opened, it will detect whether the device has been initialized. If it is not initialized, it will call the initialization interface to initialize the device by default. Open the device through the following functions:
```c
rt_err_t rt_device_open(rt_device_t dev, rt_uint16_t oflags);
```
| **Parameter** | **Description** |
| ---------- | ------------------------------- |
| dev | device handle |
| oflags | device mode flags |
| **back** | —— |
| RT_EOK | device opened successfully |
| -RT_EBUSY | If the standalone parameter RT_DEVICE_FLAG_STANDALONE is included in the functions specified when the device is registered, the device will not be allowed to be opened repeatedly |
| Other error codes | device failed to open |
oflags parameters support the following values (Use OR logic to support multiple values):
```c
#define RT_DEVICE_FLAG_STREAM 0x040 /* Stream mode */
/* Receive mode function */
#define RT_DEVICE_FLAG_INT_RX 0x100 /* Interrupt receive mode */
#define RT_DEVICE_FLAG_DMA_RX 0x200 /* DMA receiving mode */
/* Receive mode function */
#define RT_DEVICE_FLAG_INT_TX 0x400 /* Interrupt receive mode*/
#define RT_DEVICE_FLAG_DMA_TX 0x800 /* DMA receive mode */
```
There are three modes of uart data receiving and sending: interrupt mode, polling mode and DMA mode. When used, only one of the three modes can be selected. If the open parameter oflag of the serial port does not specify the use of interrupt mode or DMA mode, the polling mode is used by default.
The DMA (Direct Memory Access) transfer mode does not require the CPU to directly control the transfer, and does not have the process of reserving the scene and restoring the scene as they have in the interrupt processing mode. The DMA controller opens a path for directly transferring data to the RAM and the I/O device, which saves CPU resources to do other things. Using DMA transfer can continuously acquire or send a piece of information without taking up interrupts or delays, which is useful when communication is frequent or when large pieces of information are to be transmitted.
>RT_DEVICE_FLAG_STREAM: Stream mode is used to output a string to the serial terminal: when the output character is `"\n"` (corresponding to the hexadecimal value 0x0A), a ``\r"` is automatically output in front (corresponding to hexadecimal value is 0x0D).
The stream mode `RT_DEVICE_FLAG_STREAM` can be used with the receive and send mode parameter with the "|" logic.
An example of using a uart device in **interrupt receive mode and polling mode** as follows:
```c
#define SAMPLE_UART_NAME "uart2" /* uart device name */
static rt_device_t serial; /* uart device handle */
/* find uart device */
serial = rt_device_find(SAMPLE_UART_NAME);
/* Open the uart device in interrupt receive mode and polling mode*/
rt_device_open(serial, RT_DEVICE_FLAG_INT_RX);
```
If the uart is to use the DMA receive mode, the oflags takes the value RT_DEVICE_FLAG_DMA_RX. An example of using a uart device in the **DMA receive and polling send mode** is as follows:
```c
#define SAMPLE_UART_NAME "uart2" /* uart device's name */
static rt_device_t serial; /* uart device handle */
/* find uart device */
serial = rt_device_find(SAMPLE_UART_NAME);
/* Open the uart device in DMA receive and polling send mode*/
rt_device_open(serial, RT_DEVICE_FLAG_DMA_RX);
```
### Control UART Device
Through command control word, the application can configure the uart device by the following function:
```c
rt_err_t rt_device_control(rt_device_t dev, rt_uint8_t cmd, void* arg);
```
| **Parameter** | **Description** |
| ----------------- | ------------------------------------------------------------ |
| dev | device handle |
| cmd | command control word can be valued as：RT_DEVICE_CTRL_CONFIG |
| arg | controlled parameter： struct serial_configure |
| **Back** | —— |
| RT_EOK | function executed successfully |
| -RT_ENOSYS | execution failed, dev is empty |
| Other error codes | execution failed |
* The prototype of control parameter structure: struct serial_configure is as follows：
```c
struct serial_configure
{
rt_uint32_t baud_rate; /* Baudrate */
rt_uint32_t data_bits :4; /* Data bit */
rt_uint32_t stop_bits :2; /* Stop bit */
rt_uint32_t parity :2; /* Parity bit */
rt_uint32_t bit_order :1; /* Prioritized by order */
rt_uint32_t invert :1; /* Mode */
rt_uint32_t bufsz :16; /* Receive data buffer size */
rt_uint32_t reserved :4; /* Reserved bit */
};
```
* The default macro configuration provided by RT-Thread is as follows：
```c
#define RT_SERIAL_CONFIG_DEFAULT \
{ \
BAUD_RATE_115200, /* 115200 bps */ \
DATA_BITS_8, /* 8 databits */ \
STOP_BITS_1, /* 1 stopbit */ \
PARITY_NONE, /* No parity */ \
BIT_ORDER_LSB, /* LSB first sent */ \
NRZ_NORMAL, /* Normal mode */ \
RT_SERIAL_RB_BUFSZ, /* Buffer size */ \
0 \
}
```
The configuration parameters provided by RT-Thread can be defined as the following macro definitions:：
```c
/* The baudrate can be defined as*/
#define BAUD_RATE_2400 2400
#define BAUD_RATE_4800 4800
#define BAUD_RATE_9600 9600
#define BAUD_RATE_19200 19200
#define BAUD_RATE_38400 38400
#define BAUD_RATE_57600 57600
#define BAUD_RATE_115200 115200
#define BAUD_RATE_230400 230400
#define BAUD_RATE_460800 460800
#define BAUD_RATE_921600 921600
#define BAUD_RATE_2000000 2000000
#define BAUD_RATE_3000000 3000000
/* Data bits can be defined as*/
#define DATA_BITS_5 5
#define DATA_BITS_6 6
#define DATA_BITS_7 7
#define DATA_BITS_8 8
#define DATA_BITS_9 9
/* Stop bits can be defined as */
#define STOP_BITS_1 0
#define STOP_BITS_2 1
#define STOP_BITS_3 2
#define STOP_BITS_4 3
/* Parity bits can be defined as */
#define PARITY_NONE 0
#define PARITY_ODD 1
#define PARITY_EVEN 2
/* Bit order can be defined as */
#define BIT_ORDER_LSB 0
#define BIT_ORDER_MSB 1
/* Mode canbe defined as */
#define NRZ_NORMAL 0 /* normal mode */
#define NRZ_INVERTED 1 /* inverted mode */
/* Default size of the receive data buffer */
#define RT_SERIAL_RB_BUFSZ 64
```
**Receive Buffer**
When the uart device is opened using interrupt receive mode, the uart driver framework will open a buffer according to the size of RT_SERIAL_RB_BUFSZ to save the received data. When the underlying driver receives a data, it will put the data into the buffer in the interrupt service program.
>The default size of the receive data buffer is 64 bytes. If the number of received data in one-time is too large and the data is not read in time, the data of the buffer will be overwritten by the newly received data, resulting in data loss. It is recommended to increase the buffer.
A sample for configuring uart hardware parameters such as data bits, check bits, stop bits, and so on are shown below：
```c
#define SAMPLE_UART_NAME "uart2" /* uart device's name */
static rt_device_t serial; /* uart device handle */
struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT; /* Configuration parameters */
/* Find uart devices */
serial = rt_device_find(SAMPLE_UART_NAME);
/* Open the uart device in interrupt receive and polling send mode */
rt_device_open(serial, RT_DEVICE_FLAG_INT_RX);
config.baud_rate = BAUD_RATE_115200;
config.data_bits = DATA_BITS_8;
config.stop_bits = STOP_BITS_2;
config.parity = PARITY_NONE;
/* The serial port configuration parameters can only be modified after opening the device */
rt_device_control(serial, RT_DEVICE_CTRL_CONFIG, &config);
```
### Send Data
To write data to the serial port, the following functions can be used:
```c
rt_size_t rt_device_write(rt_device_t dev, rt_off_t pos, const void* buffer, rt_size_t size);
```
| **Parameter** | **Description** |
| ---------- | ------------------------------------------ |
| dev | device handle |
| pos | Write data offset, this parameter is not used in uart device |
| buffer | Memory buffer pointer, place the data to be written |
| size | The size of the written data |
| **back** | —— |
| The actual size of the written data | If it is a character device, the return size is in bytes; |
| 0 | It needs to read the current thread's errno to determine the error status |
Calling this function will write the data in the `buffer` to the `dev` device, the size of the write data is: size.
The sample program for writing data to the serial port is as follows:
```c
#define SAMPLE_UART_NAME "uart2" /* uart device's name */
static rt_device_t serial; /* uart device handle */
char str[] = "hello RT-Thread!\r\n";
struct serial_configure config = RT_SERIAL_CONFIG_DEFAULT; /* Configuration parameter */
/*find uart device */
serial = rt_device_find(SAMPLE_UART_NAME);
/* Open the uart device in interrupt reception and polling mode */
rt_device_open(serial, RT_DEVICE_FLAG_INT_RX);
/* Send string */
rt_device_write(serial, 0, str, (sizeof(str) - 1));
```
### Set The Send completion Callback Function
When the application calls `rt_device_write()` to write data, if the underlying hardware can support automatic transmission, the upper application can set a callback function. This callback function is called after the underlying hardware data has been sent (for example, when the DMA transfer is complete or the FIFO has been written to complete the completion interrupt). You can set the device to send completion instructions by the following function:
```c
rt_err_t rt_device_set_tx_complete(rt_device_t dev, rt_err_t (*tx_done)(rt_device_t dev,void *buffer));
```
| **Parameter** | **Description** |
| ------------- | ------------------------- |
| dev | device handle |
| tx_done | callback function pointer |
| **back** | —— |
| RT_EOK | set up successfully |
When this function is called, the callback function is provided by the user. When the hardware device sends the data, the device driver calls back this function and passes the sent data block address buffer as a parameter to the upper application. When the application (thread) receives the indication, it will release the buffer memory block or use it as the buffer for the next write data according to the condition of sending the buffer.
### Set The Receive Callback Function
The data receiving instruction can be set by the following function. When the serial port receives the data, it will inform the upper application thread that the data has arrived:
```c
rt_err_t rt_device_set_rx_indicate(rt_device_t dev, rt_err_t (*rx_ind)(rt_device_t dev,rt_size_t size));
```
| **Parameter** | **Description** |
| -------- | ------------ |
| dev | device handle |
| rx_ind | callback function pointer |
| dev | device handle (callback function parameter) |
| size | buffer data size (callback function parameter) |
| **back** | —— |
| RT_EOK | set up successfully |
The callback function for this function is provided by the user. If the uart device is opened in interrupt receive mode, the callback function will be called when the serial port receives a data, and the data size of the buffer will be placed in the `size` parameter, and the uart device handle will be placed in the `dev` parameter.
If the uart is opened in DMA receive mode, the callback function is called when the DMA completes receiving a batch of data.
Normally the receiving callback function can send a semaphore or event to notify the serial port data processing thread that data has arrived. The example is as follows:
```c
#define SAMPLE_UART_NAME "uart2" /* uart device name */
static rt_device_t serial; /* uart device handle */
static struct rt_semaphore rx_sem; /* The semaphore used to receive the message */
/* Receive data callback function */
static rt_err_t uart_input(rt_device_t dev, rt_size_t size)
{
/* When the serial port receives the data, it triggers interrupts, calls this callback function, and sends the received semaphore */
rt_sem_release(&rx_sem);
return RT_EOK;
}
static int uart_sample(int argc, char *argv[])
{
serial = rt_device_find(SAMPLE_UART_NAME);
/* Open the uart device in interrupting receive mode */
rt_device_open(serial, RT_DEVICE_FLAG_INT_RX);
/* Initialization semaphore */
rt_sem_init(&rx_sem, "rx_sem", 0, RT_IPC_FLAG_FIFO);
/* Set the receive callback function */
rt_device_set_rx_indicate(serial, uart_input);
}
```
### Receive Data
You can call the following function to read the data received by the uart:
```c
rt_size_t rt_device_read(rt_device_t dev, rt_off_t pos, void* buffer, rt_size_t size);
```
| **Parameter** | **Description** |
| -------------------------------- | ------------------------------------------------------------ |
| dev | device handle |
| pos | Read data offset, uart device dose not use this parameter |
| buffer | Buffer pointer, the data read will be saved in the buffer |
| size | Read the size of the data |
| **back** | —— |
| Read the actual size of the data | If it is a character device, the return size is in bytes. |
| 0 | It needs to read the current thread's errno to determine the error status |
Read data offset: pos is not valid for character devices. This parameter is mainly used for block devices.
An example of using the interrupt receive mode with the receive callback function is as follows:
```c
static rt_device_t serial; /* uart device handle */
static struct rt_semaphore rx_sem; /* Semaphore used to receive messages */
/* Thread receiving data */
static void serial_thread_entry(void *parameter)
{
char ch;
while (1)
{
/* Reads a byte of data from the serial port and waits for the receiving semaphore if it is not read */
while (rt_device_read(serial, -1, &ch, 1) != 1)
{
/* Blocking waiting to receive semaphore, waiting for the semaphore to read the data again*/
rt_sem_take(&rx_sem, RT_WAITING_FOREVER);
}
/* Read the data through the serial port dislocation output*/
ch = ch + 1;
rt_device_write(serial, 0, &ch, 1);
}
}
```
### Close The UART Device
After the application completes the serial port operation, the uart device can be closed by the following functions:
```c
rt_err_t rt_device_close(rt_device_t dev);
```
| **Parameter** | **Description** |
| ----------------- | ------------------------------------------------------------ |
| dev | device handle |
| **back** | —— |
| RT_EOK | device closed successfully |
| -RT_ERROR | The device has been completely shut down and cannot be shut down repeatedly |
| other error codes | fail to close the device |
Use the `rt_device_close()` interface and `rt_device_open()` interface in pair. When you open the device, you need to close the device once, so that the device will be completely shut down, otherwise the device will remain open.
## Examples Of Using UART Device
### Interrupt Receiving And Polling Send
The main steps of the sample code are as follows:
1. First find the uart device to get the device handle.
2. Initialize the semaphore that the callback function sends, and then open the uart device in read/write and interrupt receive mode.
3. Set the receive callback function of the uart device, then send the string and create a read data thread.
4. The read data thread will try to read a character data. If there is no data, it will hang and wait for the semaphore. When the uart device receives a data, it will trigger an interrupt and call the receive callback function. This function will send a semaphore to wake up the thread. At this point, the thread will immediately read the received data.
5. This sample code is not limited to a specific BSP. According to the uart device registered by BSP, modify the uart device's name corresponding to the sample code's macro definition SAMPLE_UART_NAME to run.
The running sequence diagram is shown as follows:
![Serial Port Interrupt Reception and Polling Transmission Sequence Diagram](figures/uart-int.png)
```c
/*
* Program list: This is a uart device usage routine
* The routine exports the uart_sample command to the control terminal
* Format of command: uart_sample uart2
* Command explanation: the second parameter of the command is the name of the uart device. If it is null, the default uart device wil be used
* Program function: output the string "hello RT-Thread!" through the serial port, and then malposition the input character
*/
#include <rtthread.h>
#define SAMPLE_UART_NAME "uart2"
/* Semaphore used to receive messages */
static struct rt_semaphore rx_sem;
static rt_device_t serial;
/* Receive data callback function */
static rt_err_t uart_input(rt_device_t dev, rt_size_t size)
{
/* After the uart device receives the data, it generates an interrupt, calls this callback function, and then sends the received semaphore. */
rt_sem_release(&rx_sem);
return RT_EOK;
}
static void serial_thread_entry(void *parameter)
{
char ch;
while (1)
{
/* Read a byte of data from the serial port and wait for the receiving semaphore if it is not read */
while (rt_device_read(serial, -1, &ch, 1) != 1)
{
/* Being Suspended and waiting for the semaphore */
rt_sem_take(&rx_sem, RT_WAITING_FOREVER);
}
/* Read the data from the serial port and output through dislocation */
ch = ch + 1;
rt_device_write(serial, 0, &ch, 1);
}
}
static int uart_sample(int argc, char *argv[])
{
rt_err_t ret = RT_EOK;
char uart_name[RT_NAME_MAX];
char str[] = "hello RT-Thread!\r\n";
if (argc == 2)
{
rt_strncpy(uart_name, argv[1], RT_NAME_MAX);
}
else
{
rt_strncpy(uart_name, SAMPLE_UART_NAME, RT_NAME_MAX);
}
/* Find uart devices in the system */
serial = rt_device_find(uart_name);
if (!serial)
{
rt_kprintf("find %s failed!\n", uart_name);
return -RT_ERROR;
}
/* Initialize the semaphore */
rt_sem_init(&rx_sem, "rx_sem", 0, RT_IPC_FLAG_FIFO);
/* Open the uart device in interrupt receive and polling send mode */
rt_device_open(serial, RT_DEVICE_FLAG_INT_RX);
/* Set the receive callback function */
rt_device_set_rx_indicate(serial, uart_input);
/* Send string */
rt_device_write(serial, 0, str, (sizeof(str) - 1));
/* Create a serial thread */
rt_thread_t thread = rt_thread_create("serial", serial_thread_entry, RT_NULL, 1024, 25, 10);
/* Start the thread successfully */
if (thread != RT_NULL)
{
rt_thread_startup(thread);
}
else
{
ret = -RT_ERROR;
}
return ret;
}
/* Export to the msh command list */
MSH_CMD_EXPORT(uart_sample, uart device sample);
```
### DMA Reception And Polling Transmission
When the serial port receives a batch of data, it will call the receive callback function. The receive callback function will send the data size of the buffer at this time to the waiting data processing thread through the message queue. After the thread gets the message, it is activated and reads the data. In general, the DMA receive mode completes data reception in conjunction with the DMA receive completion interrupt and the serial port idle interrupt.
* This sample code is not limited to a specific BSP. According to the uart device registered by BSP, modify the sample code macro to define the uart device name corresponding to SAMPLE_UART_NAME to run.
The running sequence diagram is shown below:
![Serial DMA Receiving and Polling Transmission Sequence Diagram](figures/uart-dma.png)
```c
/*
* Program list: This is a uart device DMA receive usage routine
* The routine exports the uart_dma_sample command to the control terminal
* Command format: uart_dma_sample uart3
* Command explanation: The second parameter of the command is the name of the uart device to be used. If it is empty, the default uart device will be used.
* Program function: output the string "hello RT-Thread!" through the serial port, and output the received data through the serial port, and then print the received data.
*/
#include <rtthread.h>
#define SAMPLE_UART_NAME "uart3" /* uart device name */
/* Serial port receiving message structure*/
struct rx_msg
{
rt_device_t dev;
rt_size_t size;
};
/* uart device handle */
static rt_device_t serial;
/* Message queue control block*/
static struct rt_messagequeue rx_mq;
/* Receive data callback function */
static rt_err_t uart_input(rt_device_t dev, rt_size_t size)
{
struct rx_msg msg;
rt_err_t result;
msg.dev = dev;
msg.size = size;
result = rt_mq_send(&rx_mq, &msg, sizeof(msg));
if ( result == -RT_EFULL)
{
/* message queue full */
rt_kprintf("message queue full！\n");
}
return result;
}
static void serial_thread_entry(void *parameter)
{
struct rx_msg msg;
rt_err_t result;
rt_uint32_t rx_length;
static char rx_buffer[RT_SERIAL_RB_BUFSZ + 1];
while (1)
{
rt_memset(&msg, 0, sizeof(msg));
/* Read messages from the message queue*/
result = rt_mq_recv(&rx_mq, &msg, sizeof(msg), RT_WAITING_FOREVER);
if (result == RT_EOK)
{
/*Read data from the serial port*/
rx_length = rt_device_read(msg.dev, 0, rx_buffer, msg.size);
rx_buffer[rx_length] = '\0';
/* Output the read message through the uart device: serial */
rt_device_write(serial, 0, rx_buffer, rx_length);
/* Print data */
rt_kprintf("%s\n",rx_buffer);
}
}
}
static int uart_dma_sample(int argc, char *argv[])
{
rt_err_t ret = RT_EOK;
char uart_name[RT_NAME_MAX];
static char msg_pool[256];
char str[] = "hello RT-Thread!\r\n";
if (argc == 2)
{
rt_strncpy(uart_name, argv[1], RT_NAME_MAX);
}
else
{
rt_strncpy(uart_name, SAMPLE_UART_NAME, RT_NAME_MAX);
}
/* find uart device */
serial = rt_device_find(uart_name);
if (!serial)
{
rt_kprintf("find %s failed!\n", uart_name);
return -RT_ERROR;
}
/* Initialize message queue */
rt_mq_init(&rx_mq, "rx_mq",
msg_pool, /* a pool for storing messages */
sizeof(struct rx_msg), /* The maximum length of a message*/
sizeof(msg_pool), /* The size of the message pool */
RT_IPC_FLAG_FIFO); /* If there are multiple threads waiting, assign messages according to the order. */
/* Open the uart device in DMA receive and polling send mode */
rt_device_open(serial, RT_DEVICE_FLAG_DMA_RX);
/* Set the receive callback function */
rt_device_set_rx_indicate(serial, uart_input);
/* Send string */
rt_device_write(serial, 0, str, (sizeof(str) - 1));
/* Create a thread */
rt_thread_t thread = rt_thread_create("serial", serial_thread_entry, RT_NULL, 1024, 25, 10);
/* Start the thread if it is created successfully*/
if (thread != RT_NULL)
{
rt_thread_startup(thread);
}
else
{
ret = -RT_ERROR;
}
return ret;
}
/* Export to the msh command list */
MSH_CMD_EXPORT(uart_dma_sample, uart device dma sample);
```

228
documentation/device/watchdog/watchdog.md Normal file
View file

@ -0,0 +1,228 @@
# WATCHDOG Device
## An Introduction to WATCHDOG
The hardware watchdog timer is a timer whose timing output is connected to the reset terminal of the circuit. In a productized embedded system, in order to automatically reset the system under abnormal conditions, it generally needs a watchdog.
When the watchdog was started, the counter starts counting automatically. If it is not reset counter value before the counter overflows, the counter overflow will generate a reset signal to the CPU to restart the system. When the system is running normally, it is necessary to clear the watchdog counter within the time interval allowed by the watchdog (commonly known as "feeding the dog"), and the reset signal will not be generated. If the program can "feed the dog" on time，the system does not go wrong，otherwise the system will reset.
In general, users can feed the dog in the idlehook function and key function of RT-Thread.
## Access to the WATCHDOG Device
The application accesses the watchdog hardware through the I/O device management interface provided by RT-Thread. The related interfaces are as follows:
| **Function** | **Description** |
| ---------------- | ---------------------------------- |
| rt_device_find() | Find the device handle based on the device name of the watchdog device |
| rt_device_init() | Initialize the watchdog device |
| rt_device_control() |Control the watchdog device |
| rt_device_close() | Close the watchdog device |
### Find the Watchdog Device
The application obtains the device handle based on the watchdog device's name, and then it can operate the watchdog device. The function for finding a device is as follows:
```c
rt_device_t rt_device_find(const char* name);
```
| **Function** | **Description** |
| -------- | ---------------------------------- |
| name | the name of the watchdog device |
| **return** | —— |
| device handle | finding the corresponding device and then return to the corresponding device handle |
| RT_NULL | no corresponding device object found |
An usage example is as follows:
```c
#define IWDG_DEVICE_NAME "iwg" /* the name of the watchdog device */
static rt_device_t wdg_dev; /* device handle of the watchdog */
/* find the watchdog device based on the device's name and obtain the device handle */
wdg_dev = rt_device_find(IWDG_DEVICE_NAME);
```
### Initialize the Watchdog Device
The watchdog device need to be initialized before using, which can be done by the following function:
```c
rt_err_t rt_device_init(rt_device_t dev);
```
| **Function** | **Description** |
| ---------- | ------------------------------- |
| dev | handle of the watchdog device |
| **return** | —— |
| RT_EOK | the device succeeded initializing |
| -RT_ENOSYS | initialization failed, the watchdog device driver initialization function is empty |
| other error code | the device failed to open |
An example is as follows:
```c
#define IWDG_DEVICE_NAME "iwg" /* the name of the watchdog device */
static rt_device_t wdg_dev; /* handle of the watchdog device */
/* find the watchdog device based on the device's name and obtain the device handle */
wdg_dev = rt_device_find(IWDG_DEVICE_NAME);
/* initialize the device */
rt_device_init(wdg_dev);
```
### Control the Watchdog Device
The application can configure the watchdog device using the command control word, which can be done by the following function:
```c
rt_err_t rt_device_control(rt_device_t dev, rt_uint8_t cmd, void* arg);
```
| **Function** | **Description** |
| ---------------- | ---------------------------------- |
| dev | handle of the watchdog device |
| cmd | the command word |
| arg | controlled parameter |
| **return** | —— |
| RT_EOK | function executed successfully |
| -RT_ENOSYS | execution failed, the dev is empty |
| other error code | execution failed |
The command control word `'cmd'` can take the following macro definition values:
```c
#define RT_DEVICE_CTRL_WDT_GET_TIMEOUT (1) /* get the overflow time */
#define RT_DEVICE_CTRL_WDT_SET_TIMEOUT (2) /* set the overflow time */
#define RT_DEVICE_CTRL_WDT_GET_TIMELEFT (3) /* get the remaining time */
#define RT_DEVICE_CTRL_WDT_KEEPALIVE (4) /* feed the dog */
#define RT_DEVICE_CTRL_WDT_START (5) /* start the watchdog */
#define RT_DEVICE_CTRL_WDT_STOP (6) /* stop the watchdog */
```
An example of setting the overflow time of the watchdog is as follows:
```c
#define IWDG_DEVICE_NAME "iwg" /* the name of the watchdog device */
rt_uint32_t timeout = 1000; /* the overflow time */
static rt_device_t wdg_dev; /* handle of the watchdog device */
/* find the watchdog device based on the device's name and obtain the device handle */
wdg_dev = rt_device_find(IWDG_DEVICE_NAME);
/* initialize the device */
rt_device_init(wdg_dev);
/* set the overflow time of the watch dog */
rt_device_control(wdg_dev, RT_DEVICE_CTRL_WDT_SET_TIMEOUT, (void *)timeout);
/* set idle-hook function */
rt_thread_idle_sethook(idle_hook);
```
An example of feeding a dog in an idle thread hook function is as follows:
```c
static void idle_hook(void)
{
/* Feed the dog in the callback function of the idle thread */
rt_device_control(wdg_dev, RT_DEVICE_CTRL_WDT_KEEPALIVE, NULL);
}
```
### Close the Watchdog Device
When the application completes the operation of the watchdog, it can close the watchdog device:
```c
rt_err_t rt_device_close(rt_device_t dev);
```
| **Function** | **Description** |
| ---------- | ---------------------------------- |
| dev | handle of the watchdog device |
| **return** | —— |
| RT_EOK | close the device successfully |
| -RT_ERROR | The device has been completely shut down and cannot be closed repeatedly |
| other error code | fail to close the device |
Closing the device interface and opening the device interface need to match each other. When you open the device, you need to close the device once correspondingly, so that the device will be completely shut down, otherwise the device will remain unclosed.
## Watchdog Device usage example
The specific use of the watchdog device can be referred to the following sample code. The main steps of the sample code are as follows:
1. First find the device handle based on the device name "iwg".
2. Set the overflow time of the watchdog after initializing the device.
3. Set the idle thread callback function.
4. This callback function will run and feed the dog when the system executes idle threads.
```c
/*
* Program list: This is an independent watchdog device usage routine
* The routine exports the iwdg_sample command to the control terminal
* Command call format: iwdg_sample iwg
* Command explanation: The second parameter of the command is the name of the watchdog device to be used. If it is empty, you can use the default watchdog device of the routine.
* Program function: The program finds the watchdog device through the device's name, and then initializes the device and sets the overflow time of the watchdog device.
* Then set the idle thread callback function, which will feed the dog in the idle callback function.
*/
#include <rtthread.h>
#include <rtdevice.h>
#define IWDG_DEVICE_NAME "iwg" /* the name of the watchdog device */
static rt_device_t wdg_dev; /* handle of the watchdog device */
static void idle_hook(void)
{
/* feed the dog in the callback function */
rt_device_control(wdg_dev, RT_DEVICE_CTRL_WDT_KEEPALIVE, NULL);
rt_kprintf("feed the dog!\n ");
}
static int iwdg_sample(int argc, char *argv[])
{
rt_err_t ret = RT_EOK;
rt_uint32_t timeout = 1000; /* the overflow time */
char device_name[RT_NAME_MAX];
/* Determine if the command-line parameter is given the device name */
if (argc == 2)
{
rt_strncpy(device_name, argv[1], RT_NAME_MAX);
}
else
{
rt_strncpy(device_name, IWDG_DEVICE_NAME, RT_NAME_MAX);
}
/* find the watchdog device based on the device's name and obtain the device handle */
wdg_dev = rt_device_find(device_name);
if (!wdg_dev)
{
rt_kprintf("find %s failed!\n", device_name);
return -RT_ERROR;
}
/* initialize the device */
ret = rt_device_init(wdg_dev);
if (ret != RT_EOK)
{
rt_kprintf("initialize %s failed!\n", device_name);
return -RT_ERROR;
}
/* set the overflow time of the watch dog */
ret = rt_device_control(wdg_dev, RT_DEVICE_CTRL_WDT_SET_TIMEOUT, &timeout);
if (ret != RT_EOK)
{
rt_kprintf("set %s timeout failed!\n", device_name);
return -RT_ERROR;
}
/* set idle thread callback function */
rt_thread_idle_sethook(idle_hook);
return ret;
}
/* export to the msh command list */
MSH_CMD_EXPORT(iwdg_sample, iwdg sample);
```

BIN
documentation/device/wlan/figures/an0026_1.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 54 KiB

BIN
documentation/device/wlan/figures/an0026_3.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 27 KiB

BIN
documentation/device/wlan/figures/an0026_4.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 33 KiB

BIN
documentation/device/wlan/figures/an0026_5.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 53 KiB

443
documentation/device/wlan/wlan.md Normal file
View file

@ -0,0 +1,443 @@
# WLAN Device
With the rapid development of the Internet of Things, more and more embedded devices are equipped with WIFI wireless network devices. In order to be able to manage WIFI network devices, RT-Thread introduces a WLAN device management framework. This framework has many features to control and manage WIFI, providing developers with many conveniences for using WIFI devices.
## Introduction to the WLAN Framework
The WLAN framework is a set of middleware developed by RT-Thread for managing WIFI. Connect to the specific WIFI driver, control the WIFI connection disconnection, scan and other operations. Support different applications, provide WIFI control, events, data diversion and other operations for the application, and provide a unified WIFI control interface for the upper application. The WLAN framework consists of three main parts. The DEV driver interface layer provides a unified API for the WLAN framework. Manage layer provides users with specific functions such as WIFI scanning, connection, and disconnection. Protocol is responsible for processing the data stream generated on the WIFI. Different protocols such as LWIP can be mounted according to different usage scenarios. It has the characteristics of simple use, complete functions, convenient docking and strong compatibility.
The following figure is a hierarchical diagram of the WIFI framework:
![WIFI Framework](figures/an0026_1.png)
The First Part: `APP`, the application layer. It is a specific application based on the WLAN framework, such as WiFi-related shell commands.
The Second Part: `Airkiss and Voice`, the network configuration layer. Provide functions such as using wireless or sound waves to configure the network.
The Third Part: `WLAN Manager`, the WLAN management layer. Ability to control and manage WLAN devices. It has functions related to WLAN control, such as setting mode, connecting hotspots, disconnecting hotspots, enabling hotspots, scanning hotspots, etc. It also provides management functions such as reconnection after disconnection and automatic hotspot switching.
The Fourth Part: `WLAN Protocol`, the protocol layer. The data stream is submitted to a specific protocol for resolution, and the user can specify to communicate using different protocols.
The Fifth Part: `WLAN Config`, the parameter management layer. Manage hotspot information and passwords for successful connections and write them to non-volatile storage media.
The Sixth Part: `WLAN Device`, the driver interface layer. Connect to specific WLAN hardware and provide unified APIs for management.
### Functions
* Automatic Connection: After using automatic connection function, as long as the WIFI is disconnected, the hotspot information of the previous successful connection will be automatically read, and the hotspot will be connected. If a hotspot connection fails, switch to the next hotspot to connect until the connection is successful. The hotspot information used by the automatic connection is sequentially tried in the order of the success of the connection, and the hotspot information of the latest connection success is preferentially used. After the connection is successful, the hotspot information is cached first, and use it first when reconnecting after the next disconnection.
* Parameter storage: Stores the WIFI parameters for successful connection. The WIFI parameter will be cached in the memory. If the external non-volatile storage interface is configured, it will be stored in the external storage medium. Users can implement the `struct rt_wlan_cfg_ops` structure according to his actual situation and save the parameters anywhere. The cached parameters mainly provide hotspot information for automatic connections. When WIFI is unconnected, it will read the cached parameters and try to connect.
* WIFI control: Provide complete WIFI control APIs, scanning, connection, hotspot, etc. Provide WIFI related status callback events, disconnect, connection, connection failure, etc. Provide users with an easy to use WIFI management APIs.
* Shell command: You can enter the command in Msh to control WIFI to perform scanning, connecting, disconnecting and other actions. Print debugging information such as WIFI status.
### Configuration
Use `menuconfig` command in ENV to enter the WLAN configuration interface by following the menu:
```c
RT-Thread Components -> Device Drivers -> Using WiFi ->
```
Configuration options are described in detail as follows:
```c
[*] Using Wi-Fi framework /* Using Wi-Fi framework */
(wlan0) The WiFi device name for station /* The default name for station */
(wlan1) The WiFi device name for ap /* The default name for ap */
(lwip) Default transport protocol /* Default protocol */
(10000) Set scan timeout time(ms) /* Scan timeout time */
(10000) Set connect timeout time(ms) /* Connect timeout time */
(32) SSID name maximum length /* Maximum length of SSID name */
(32) Maximum password length /* Maximum length of password */
[*] Automatic sorting of scan results /* Automatic sorting of scan results */
(3) Maximum number of WiFi information automatically saved /* Maximum number of WiFi information automatically saved */
(wlan_job) WiFi work queue thread name /* WiFi work queue thread name */
(2048) wifi work queue thread size /* wifi work queue thread size */
(22) WiFi work queue thread priority /* WiFi work queue thread priority */
(2) Maximum number of driver events /* Maximum number of driver events in dev layer */
[ ] Forced use of PBUF transmission /* Forced use of PBUF transmission */
[ ] Enable WLAN Debugging Options /* Enable WLAN Debugging Options */
```
## Access Wi-Fi Devices
The application accesses the WLAN device hardware through the WLAN device management interface, and the relevant interfaces are as follows:
| Fuctions | **Description** |
| -------------------- | ---------------------------- |
| rt_wlan_prot_attach() | Specify the WLAN protocol attached |
| rt_wlan_scan_sync() | Synchronized WLAN Scan |
| rt_wlan_connect() | Synchronized Hotspot Connection |
| rt_wlan_disconnect() | Synchronized Hotspot Disconnection |
| rt_wlan_config_autoreconnect() | Configuration automatic reconnection mode |
### Specify Protocol
```c
rt_err_t rt_wlan_prot_attach(const char *dev_name, const char *prot_name);
```
| **Parameter** | **D**escription |
| ----------------------------- | ---------------------------------- |
| dev_name | WLAN device name |
| prot_name | Protocol name, possible values: RT_WLAN_PROT_LWIP, indicates the protocol type LWIP |
| Return | **--** |
| -RT_ERROR | Execution failed |
| RT_EOK | Execution succeed |
### Synchronized WLAN Scan
```c
struct rt_wlan_scan_result *rt_wlan_scan_sync(void);
```
| **Return** | **Description** |
| ---------- | ------------------------------- |
| rt_wlan_scan_result | Scan Result |
The scan result is a structure as follows:
```c
struct rt_wlan_scan_result
{
rt_int32_t num; /* info number */
struct rt_wlan_info *info; /* info pointer */
};
```
### Synchronized Hotspot Connection
```c
rt_err_t rt_wlan_connect(const char *ssid, const char *password);
```
| **Parameter** | **Description** |
| ----------------------------- | ---------------------------------- |
| ssid | WIFI name |
| password | WIFI password |
| Return | **--** |
| -RT_EINVAL | Parameter error |
| -RT_EIO | Unregistered device |
| -RT_ERROR | Connection failed |
| RT_EOK | Connection successful |
### Synchronized Hotspot Disconnection
```c
rt_err_t rt_wlan_disconnect(void);
```
| Return | **Description** |
| ----------------------------- | ---------------------------------- |
| -RT_EIO | Unregistered device |
| -RT_ENOMEM | Not enough memory |
| -RT_ERROR | Disconnection failed |
| RT_EOK | Disconnection successful |
### Automatic Reconnection Mode Configuration
```c
void rt_wlan_config_autoreconnect(rt_bool_t enable);
```
| **P**arameter | **Description** |
| ----------------------------- | ---------------------------------- |
| enable | enable or disable automatic reconnection |
## FinSH Command
Using shell commands can help us quickly debug WiFi-related features. The wifi related shell commands are as follows:
```c
wifi /* Print help */
wifi help /* View help */
wifi join SSID [PASSWORD] /* Connect wifi.if SSDI is empty, use configuration to connect automatically */
wifi ap SSID [PASSWORD] /* Create hotspot */
wifi scan /* Scan all hotspots */
wifi disc /* Disconnnect */
wifi ap_stop /* Stop hotspot */
wifi status /* Print wifi status sta + ap */
wifi smartconfig /* Start to configure network function */
```
### WiFi Scan
The wifi scan command is `wifi scan`. After the wifi scan command is executed, the surrounding hotspot information will be printed on the terminal. Through the printed hotspot information, you can see multiple attributes such as SSID and MAC address.
Enter the command in msh and the scan results are as follows:
```c
wifi scan
SSID MAC security rssi chn Mbps
------------------------------- ----------------- -------------- ---- --- ----
rtt_test_ssid_1 c0:3d:46:00:3e:aa OPEN -14 8 300
test_ssid 3c:f5:91:8e:4c:79 WPA2_AES_PSK -18 6 72
rtt_test_ssid_2 ec:88:8f:88:aa:9a WPA2_MIXED_PSK -47 6 144
rtt_test_ssid_3 c0:3d:46:00:41:ca WPA2_MIXED_PSK -48 3 300
```
### WiFi Connection
The wifi scan command is `wifi join`. The command needs to be followed by the hotspot name and hotspot password. If the hotspot does not have a password, you may not enter this item. After the WiFi connection command is executed, if the hotspot exists and the password is correct, the board will connect to the hotspot and obtain the IP address. After the network connection is successful, you can use `socket` sockets for network communication.
An example of using the wifi connection command is as follows. After the connection is successful, the obtained IP address will be printed on the terminal as follows:
```c
wifi join ssid_test 12345678
[I/WLAN.mgnt] wifi connect success ssid:ssid_test
[I/WLAN.lwip] Got IP address : 192.168.1.110
```
### WiFi Disconnection
The command to disconnect WiFi is `wifi disc`. After the WiFi disconnect command is executed, the development board will disconnect from the hotspot.
The WiFi disconnect command usage example is as follows. After the disconnection is successful, the following information will be printed on the terminal as shown below.
```c
wifi disc
[I/WLAN.mgnt] disconnect success!
```
## Example for WLAN Device Usage
### WiFi Scan
The following code will show a WiFi sync scan, and then print the results on the terminal. First perform WIFI initialization, and then execute the WIFI scan function `rt_wlan_scan_sync`, this function is synchronous, the number of scans and results returned by the function. In this example, the scanned hotspot name will be printed.
```c
#include <rthw.h>
#include <rtthread.h>
#include <wlan_mgnt.h>
#include <wlan_prot.h>
#include <wlan_cfg.h>
void wifi_scan(void)
{
struct rt_wlan_scan_result *result;
int i = 0;
/* Configuring WLAN device working mode */
rt_wlan_set_mode(RT_WLAN_DEVICE_STA_NAME, RT_WLAN_STATION);
/* WiFi scan */
result = rt_wlan_scan_sync();
/* Print scan results */
rt_kprintf("scan num:%d\n", result->num);
for (i = 0; i < result->num; i++)
{
rt_kprintf("ssid:%s\n", result->info[i].ssid.val);
}
}
int scan(int argc, char *argv[])
{
wifi_scan();
return 0;
}
MSH_CMD_EXPORT(scan, scan test.);
```
The results are as follows:
![Scan](figures/an0026_3.png)
### WiFi Connection and Disconnection
The code below will show a WiFi sync connection. Initialize WIFI first, and then create a semaphore for waiting for the `RT_WLAN_EVT_READY` event. Register the callback function of the event that needs attention, execute the `rt_wlan_connect` wifi connection function, and return value will indicate whether the connection has been successful. If the WiFi connection succeeds, it needs to wait for the network to get the IP address before communication. Use the semaphore created in advance to wait for the network to be ready. Once the network is ready, it will be able to communicate.
After connecting to WIFI, wait for a while and then execute `rt_wlan_disconnect` to disconnect. The disconnect operation is blocked, and the return value indicates whether the disconnection was successful.
```c
#include <rthw.h>
#include <rtthread.h>
#include <wlan_mgnt.h>
#include <wlan_prot.h>
#include <wlan_cfg.h>
#define WLAN_SSID "SSID-A"
#define WLAN_PASSWORD "12345678"
#define NET_READY_TIME_OUT (rt_tick_from_millisecond(15 * 1000))
static rt_sem_t net_ready = RT_NULL;
static void
wifi_ready_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
rt_sem_release(net_ready);
}
static void
wifi_connect_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
if ((buff != RT_NULL) && (buff->len == sizeof(struct rt_wlan_info)))
{
rt_kprintf("ssid : %s \n", ((struct rt_wlan_info *)buff->data)->ssid.val);
}
}
static void
wifi_disconnect_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
if ((buff != RT_NULL) && (buff->len == sizeof(struct rt_wlan_info)))
{
rt_kprintf("ssid : %s \n", ((struct rt_wlan_info *)buff->data)->ssid.val);
}
}
static void
wifi_connect_fail_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
if ((buff != RT_NULL) && (buff->len == sizeof(struct rt_wlan_info)))
{
rt_kprintf("ssid : %s \n", ((struct rt_wlan_info *)buff->data)->ssid.val);
}
}
rt_err_t wifi_connect(void)
{
rt_err_t result = RT_EOK;
/* Configuring WLAN device working mode */
rt_wlan_set_mode(RT_WLAN_DEVICE_STA_NAME, RT_WLAN_STATION);
/* station connect */
rt_kprintf("start to connect ap ...\n");
net_ready = rt_sem_create("net_ready", 0, RT_IPC_FLAG_FIFO);
rt_wlan_register_event_handler(RT_WLAN_EVT_READY,
wifi_ready_callback, RT_NULL);
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_CONNECTED,
wifi_connect_callback, RT_NULL);
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_DISCONNECTED,
wifi_disconnect_callback, RT_NULL);
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_CONNECTED_FAIL,
wifi_connect_fail_callback, RT_NULL);
/* connect wifi */
result = rt_wlan_connect(WLAN_SSID, WLAN_PASSWORD);
if (result == RT_EOK)
{
/* waiting for IP to be got successfully */
result = rt_sem_take(net_ready, NET_READY_TIME_OUT);
if (result == RT_EOK)
{
rt_kprintf("networking ready!\n");
}
else
{
rt_kprintf("wait ip got timeout!\n");
}
rt_wlan_unregister_event_handler(RT_WLAN_EVT_READY);
rt_sem_delete(net_ready);
rt_thread_delay(rt_tick_from_millisecond(5 * 1000));
rt_kprintf("wifi disconnect test!\n");
/* disconnect */
result = rt_wlan_disconnect();
if (result != RT_EOK)
{
rt_kprintf("disconnect failed\n");
return result;
}
rt_kprintf("disconnect success\n");
}
else
{
rt_kprintf("connect failed!\n");
}
return result;
}
int connect(int argc, char *argv[])
{
wifi_connect();
return 0;
}
MSH_CMD_EXPORT(connect, connect test.);
```
The results are as follows:
![Disconnection](figures/an0026_4.png)
### WiFi Auto Reconnection when Turn On
First enable the automatic reconnection function, use the command line to connect to the hotspot A, and connect another hotspot B. After waiting for a few seconds, power off hotspot B, the system will automatically retry connecting B hotspot. At this time, B hotspot connection can not be connected, and the system automatically switches hotspot A to connect. After the connection is successful, the system stops connecting.
```c
#include <rthw.h>
#include <rtthread.h>
#include <wlan_mgnt.h>
#include <wlan_prot.h>
#include <wlan_cfg.h>
static void
wifi_ready_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
}
static void
wifi_connect_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
if ((buff != RT_NULL) && (buff->len == sizeof(struct rt_wlan_info)))
{
rt_kprintf("ssid : %s \n", ((struct rt_wlan_info *)buff->data)->ssid.val);
}
}
static void
wifi_disconnect_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
if ((buff != RT_NULL) && (buff->len == sizeof(struct rt_wlan_info)))
{
rt_kprintf("ssid : %s \n", ((struct rt_wlan_info *)buff->data)->ssid.val);
}
}
static void
wifi_connect_fail_callback(int event, struct rt_wlan_buff *buff, void *parameter)
{
rt_kprintf("%s\n", __FUNCTION__);
if ((buff != RT_NULL) && (buff->len == sizeof(struct rt_wlan_info)))
{
rt_kprintf("ssid : %s \n", ((struct rt_wlan_info *)buff->data)->ssid.val);
}
}
int wifi_autoconnect(void)
{
/* Configuring WLAN device working mode */
rt_wlan_set_mode(RT_WLAN_DEVICE_STA_NAME, RT_WLAN_STATION);
/* Start automatic connection */
rt_wlan_config_autoreconnect(RT_TRUE);
/* register event */
rt_wlan_register_event_handler(RT_WLAN_EVT_READY,
wifi_ready_callback, RT_NULL);
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_CONNECTED,
wifi_connect_callback, RT_NULL);
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_DISCONNECTED,
wifi_disconnect_callback, RT_NULL);
rt_wlan_register_event_handler(RT_WLAN_EVT_STA_CONNECTED_FAIL,
wifi_connect_fail_callback, RT_NULL);
return 0;
}
int auto_connect(int argc, char *argv[])
{
wifi_autoconnect();
return 0;
}
MSH_CMD_EXPORT(auto_connect, auto connect test.);
```
The results are as follows:
![Autoconnection](figures/an0026_5.png)

314
documentation/dlmodule/README.md Normal file
View file

@ -0,0 +1,314 @@
# Dynamic Module: dlmodule #
In traditional desktop operating systems, user space and kernel space are separate. The application runs in user space, and the kernel and kernel modules run in kernel space. The kernel module can be dynamically loaded and deleted to extend the kernel functionality. `dlmodule` is a software component of the dynamic module loading mechanism provided in kernel space of RT-Thread. In versions of RT-Thread v3.1.0, this was also called the `Application Module`. After RT-Thread v3.1.0 and later, it returned to the tradition and was named after the `dynamic module`.
`dlmodule` is more of an ELF format loader. The code segment and data segment of a separately compiled elf file are loaded into memory, and the symbols are parsed and bound to the API address exported by the kernel. The elf files are primarily placed on file systems under RT-Thread.
## Introduction ##
The dynamic module provides a mechanism for dynamically loading program modules for RT-Thread. Because it is also compiled independently of the kernel, it is more flexible to use. In terms of implementation, this is a mechanism to separate the kernel from the dynamic modules. Through this mechanism, the kernel and dynamic modules can be compiled separately, and at runtime, the compiled dynamic modules are loaded into the kernel through the module loader in the kernel.
In the dynamic module of RT-Thread, two formats are currently supported:
* `.mo` is an executable dynamic module that is suffixed with `.mo` when compiled; it can be loaded, and a main thread is automatically created in the system to execute `main()` function in this dynamic module; at the same time, `main(int argc, char**argv)` can also accept arguments on the command line.
* `.so` is a dynamic library compiled with `.so` as a suffix; it can be loaded and resided in memory, and some set of functions is used by other programs (code or dynamic modules in the kernel).
The current RT-Thread architecture supporting dynamic modules mainly includes ARM architecture and x86 architecture, and will be extended to MIPS and RISC-V architecture in the future. The RT-Thread kernel firmware section can use a variety of compiler toolchains, such as GCC, ARMCC, IAR and other toolchains; however, dynamic module partial compilation currently only supports GNU GCC toolchain compilation. Therefore, compiling the RT-Thread module requires downloading GCC tools, such as CodeSourcery's arm-none-eabi toolchain. In general, it's best to use kernel and dynamic modules to compile with the same toolchain (so that it doesn't produce inconsistent behavior in *libc*). In addition, dynamic modules can only be loaded into RAM and used for symbol resolution binding to the API address exported by the kernel. Instead of running directly in XIP mode based on Flash (because Flash can't modify the code segment again).
## Using Dynamic Module ##
When you want to use the dynamic modules in your system, you need to compile a firmware that supports dynamic modules, as well as dynamic modules that need to be run. The following two parts are compiling firmware and compiling dynamic modules.
### Compile Firmware ###
When you want to use the dynamic module, you need to open the corresponding option in the firmware configuration, use menuconfig to open the following configuration:
```c
RT-Thread Components --->
POSIX layer and C standard library --->
[*] Enable dynamic module with dlopen/dlsym/dlclose feature
```
Also open the configuration options of the file system:
```c
RT-Thread Components --->
Device virtual file system --->
[*] Using device virtual file system
```
The configuration parameters required for dynamic module compilation are set in *rtconfig.py* file corresponding to bsp:
```Python
M_CFLAGS = CFLAGS + '-mlong-calls -fPIC'
M_CXXFLAGS = CXXFLAGS + '-mlong-calls -fPIC'
M_LFLAGS = DEVICE + CXXFLAGS + '-Wl,--gc-sections,-z,max-page-size=0x4' +\
'-shared -fPIC -nostartfiles -nostdlib -static-libgcc'
M_POST_ACTION = STRIP + '-R .hash $TARGET\n' + SIZE + '$TARGET \n'
M_BIN_PATH = r'E:\qemu-dev310\fatdisk\root'
```
The relevant explanation is as follows:
* **M_CFLAGS**: C code compilation parameters used in dynamic module compilation, generally compiled here in PIC mode (that is, the code address supports floating mode execution);
- **M_CXXFLAGS**: C++ code compilation parameters used in dynamic module compilation, parameters similar to M_CFLAGS above;
- **M_LFLAGS**: Parameters when the dynamic module is linked. The same is the PIC method, and is linked in a shared library (partial link);
- **M_POST_ACTION**: the action to be performed after the dynamic module is compiled. Here, the elf file is stripped to reduce the size of the elf file.
- **M_BIN_PATH**: When the dynamic module is successfully compiled, whether the corresponding dynamic module file needs to be copied to a unified place;
Basically, these compilation configuration parameters for the ARM9, Cortex-A, and Cortex-M series are the same.
The kernel firmware also exports some function APIs to the dynamic module via `RTM(function)`. All exported symbols information in firmware can be listed by command A under MSH:
```
list_symbols
```
The `dlmodule` loader also parses the symbols that need to be parsed in the dynamic module according to the symbol table exported here to complete the final binding action.
This symbol table will be placed in a special section named `RTMSymTab`, so the corresponding firmware link script also needs to retain this area, and will not be removed by the linker optimization. You can add the corresponding information in the link script:
```text
/* section information for modules */
. = ALIGN(4);
__rtmsymtab_start = .;
KEEP(*(RTMSymTab))
__rtmsymtab_end = .;
```
Then execute the `scons` under the BSP project directory and generate the firmware without errors. Execute the command in the BSP project directory:
`scons --target=ua -s`
to generate the kernel header file search path and global macro definitions that need to be included when compiling the dynamic module.
### Compile Dynamic Module ###
There is a separate repository on github: [rtthread-apps](https://github.com/RT-Thread/rtthread-apps) , which contains some examples of dynamic modules and dynamic libraries.
Its directory structure is as follows:
| **Directory** | **Description** |
| --- | ---------------- |
| cxx | Demonstrates how to program in C++ using dynamic modules |
| hello | A "hello world" example |
| lib | Example of dynamic library |
| md5 | Generate md5 code for a file |
| tools | *Python/SConscript* scripts required for dynamic module compilation |
| ymodem | Download a file to the file system through the serial port using the YModem protocol |
You can clone this repository locally and compile it with the scons from the command line. For Windows platforms, the ENV tool is recommended.
After entering the console command line, enter the directory where the `rtthread-apps` repo is located (the same, please ensure that the full path of this directory does not contain spaces, Chinese characters, etc.), and set two variables:
* RTT_ROOT: points to the root directory of the RT-Thread code;
- BSP_ROOT: points to the project directory of the BSP;
Use follow commands on Windows in Env tool(assuming the BSP used is qemu-vexpress-a9):
```c
set RTT_ROOT=d:\your_rtthread
set BSP_ROOT=d:\your_rtthread\bsp\qemu-vexpress-a9
```
to set the corresponding environment variable. Then use the following command to compile the dynamic module, such as the hello example:
```
scons --app=hello
```
After compiling successfully, it will generate a `hello.mo` file in the `rtthread-apps/hello` directory.
You can also compile dynamic libraries, such as the lib example:
```
scons --lib=lib
```
After compiling successfully, it will generate the `lib.so` file in the `rtthread-apps/lib` directory.
We can put these `mo` and `so` files under the RT-Thread file system. Under msh, you can simply execute the `hello.mo` dynamic module as a `hello` command:
```c
msh />ls
Directory /:
hello.mo 1368
lib.so 1376
msh />hello
msh />Hello, world
```
After calling hello, the main function in `hello.mo` will be executed, and the corresponding dynamic module will be exited after execution. The code for `hello/main.c` is as follows:
```c
#include <stdio.h>
int main(int argc, char *argv[])
{
printf("Hello, world\n");
return 0;
}
```
## APIs of Dynamic Module
In addition to dynamically loading and executing dynamic modules via msh, dynamic modules can be loaded or unloaded using the dynamic module API provided by RT-Thread in the main program.
### Load Dynamic Module
```c
struct rt_dlmodule *dlmodule_load(const char* pgname);
```
|**Parameter**|**Description**|
| ---- | ---- |
| pgname | Dynamic module path |
|**Return**| —— |
| Dynamic module pointer | Successfully loaded |
| RT_NULL | Failed |
This function loads the dynamic module from the file system into memory, and if it is loaded correctly, returns a pointer to the module. This function does not create a thread to execute this dynamic module, just load the module into memory and parse the symbolic address.
### Execute Dynamic Module
```c
struct rt_dlmodule *dlmodule_exec(const char* pgname, const char* cmd, int cmd_size);
```
|**Parameter**|**Description**|
| ---- | ---- |
| pgname | Dynamic module path |
| cmd | Command line string including the dynamic module command itself |
| cmd_size | Command line string size |
|**Return**| —— |
| Dynamic module pointer | Run successfully |
| RT_NULL | Failed |
This function loads the dynamic module according to the `pgname` path and starts a thread to execute `main` of the dynamic module. At the same time, `cmd` is passed as the command line Parameter to `main` entry of the dynamic module.
### Exit Dynamic Module
```c
void dlmodule_exit(int ret_code);
```
|**Parameter**|**Description**|
| ---- | ---- |
| ret_code | Module's return parameter |
This function is called by the module runtime, it can set the return value of the module exit `ret_code`, and then exit from the module.
### Find Dynamic Modules
```c
struct rt_dlmodule *dlmodule_find(const char *name);
```
|**Parameter**|**Description**|
| ---- | ---- |
| name | Module name |
|**Return**| —— |
| Dynamic module pointer | Successful |
| RT_NULL | Failed |
This function uses `name` to find out if there is already a dynamic module loaded in the system.
### Return Dynamic Module
```c
struct rt_dlmodule *dlmodule_self(void);
```
|**Return**|**Description**|
| ---- | ---- |
| Dynamic module pointer | Successful |
| RT_NULL | Failed |
This function returns a pointer of the dynamic module in the calling context.
### Find Symbol
```c
rt_uint32_t dlmodule_symbol_find(const char *sym_str);
```
|**Parameter**|**Description**|
| ---- | ---- |
| sym_str | Symbol name |
|**Return**| —— |
| Symbol address | Successful |
| 0 | Failed |
This function returns the symbol address based on the symbol name.
## Libdl API of POSIX Standard ##
The POSIX standard libdl API is also supported in RT-Thread dlmodule. It is similar to loading a dynamic library into memory (and parsing some of the symbol information). This dynamic library provides the corresponding set of function operations. The libdl API needs to include the header files: `#include <dlfcn.h>`
### Open Dynamic Library
```c
void * dlopen (const char * pathname, int mode);
```
|**Parameter**|**Description**|
| ---- | ---- |
| pathname | Dynamic library path name |
| mode | The mode when opening a dynamic library, not used in RT-Thread |
|**Return**| —— |
| Dynamic library handle (`struct dlmodule` structure pointer) | Successful |
| NULL | Failed |
This function is similar to the `dlmodule_load` , which loads the dynamic library from the file system and returns the handle pointer of the dynamic library.
### Find Symbol
```c
void* dlsym(void *handle, const char *symbol);
```
|**Parameter**|**Description**|
| ---- | ---- |
| handle | Dynamic library handle, return value of `dlopen` |
| symbol | The symbol address to return |
|**Return**| —— |
| symbol address | Successful |
| NULL | Failed |
This function looks in the dynamic library `handle` for the presence of the symbol of `symbol` , if there is an address that returns it.
### Close Dynamic Library
```
int dlclose (void *handle);
```
|**Parameter**|**Description**|
| ---- | ---- |
| handle | Dynamic library handle |
|**Return**| —— |
| 0 | Successful |
| Negative number | Failed |
This function closes the dynamic library pointed to by `handle` and unloads it from memory. It should be noted that when the dynamic library is closed, the symbolic address originally returned by `dlsym` will no longer be available. If you still try to access it, it may cause a fault error.
## FAQs
Please refer to [*User Manual of Env*](../env/env.md) for issues related to the Env tool.
### Q: Dynamic modules cannot be run successfully according to the documentation.
**A:** Please update the RT-Thread source code to version 3.1.0 and above.
### Q: Compile the project with the scons command, prompting "undefined reference to __rtmsymtab_start".
**A:** Please refer to the qemu-vexpress-a9 BSP GCC link script file *link.lds* to add the following to the TEXT section of the project's GCC link script.
```
/* section information for modules */
. = ALIGN(4);
__rtmsymtab_start = .;
KEEP(*(RTMSymTab))
__rtmsymtab_end = .;
```

2
documentation/doxygen/.gitignore vendored Normal file
View file

@ -0,0 +1,2 @@
html/
latex/

2715
documentation/doxygen/Doxyfile Normal file
View file

File diff suppressed because it is too large Load diff

14
documentation/doxygen/basicdef.h Normal file
View file

@ -0,0 +1,14 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup BasicDef Basic Definitions
*
* @brief Basic data type in RT-Thread RTOS.
*
* These are the basic definitions which used in RT-Thread RTOS. In general,
* RT-Thread kernel uses its own definition of the basic data types, such as
* rt_uint32_t, rt_uint8_t, etc., which does not depend on the compiler or
* architecture.
*/

44
documentation/doxygen/filesystem.h Normal file
View file

@ -0,0 +1,44 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup DFS Device Virtual File System
*
* @brief DFS is a virtual file system in RT-Thread RTOS.
*
* The DFS (Device Virtual File System) is a vfs file system of RT-Thread RTOS,
* which is focused on embedded device. VFS is an abstraction layer on top of a
* more concrete file system. The purpose of a VFS is to allow client applications
* to access different types of concrete file systems in a uniform way.
*
* @image html dfs.png "Figure 4: Device Virtual File System Architecture"
*
* The DFS specifies an interface between the kernel and a concrete file system.
* Therefore, it is easy to add support for new file system types to the kernel
* simply by fulfilling the interface.
*/
/**
* @addtogroup DFS
* @{
*/
/**
* @defgroup Fd File Descriptor
*
*/
/**
* @defgroup FsApi File System API
*/
/**
* @defgroup FileApi File API
*/
/**
* @defgroup FsPosixApi File POSIX API
*/
/**@}*/

19
documentation/doxygen/finsh.h Normal file
View file

@ -0,0 +1,19 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup finsh finsh shell
*
* @brief finsh shell is a user command shell in RT-Thread RTOS.
*
* finsh shell is a user command shell in RT-Thread RTOS, which is a shell can
* accept C-expression like syntax in command. From finsh shell, user can access
* system area, such as memory, variables and function by input C-expression in
* command.
*
* @image html finsh.png "Figure 3: finsh shell architecture"
* There is a shell thread, which named as "tshell", in the finsh shell, it read
* user command from console device, and then invokes system function or access
* system variable to output result (by rt_kprintf).
*/

87
documentation/doxygen/hardware.h Normal file
View file

@ -0,0 +1,87 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup bsp Hardware Related Package
*
* @brief Hardware Related Package includes board support package(BSP) and CSP(Chip
* Support Package).
*
* Board Support Package(BSP) is the hardware related wrapper, for example, peripherals
* in board, the pinmux setting etc. In RT-Thread RTOS, the bsp is placed under bsp
* directory.
*
* Chip Support Package(CSP) is a software set that contains chip specific software.
* A CSP usually includes operating system porting and peripheral device drivers inside
* chip. In RT-Thread RTOS, the csp is placed under libcpu directory.
*/
/**
* @addtogroup bsp
* @{
*/
/**
* This function will return current system interrupt status and disable system
* interrupt.
*
* @return the current system interrupt status.
*/
rt_base_t rt_hw_interrupt_disable(void);
/**
* This function will set the specified interrupt status, which shall saved by
* rt_hw_intterrupt_disable function. If the saved interrupt status is interrupt
* opened, this function will open system interrupt status.
*
* @param level the interrupt status to be set.
*/
void rt_hw_interrupt_enable(rt_base_t level);
/**
* This function initializes interrupt.
*/
void rt_hw_interrupt_init(void);
/**
* This function masks the specified interrupt.
*
* @param vector the interrupt number to be masked.
*
* @note not all of platform provide this function.
*/
void rt_hw_interrupt_mask(int vector);
/**
* This function umasks the specified interrupt.
*
* @param vector the interrupt number to be unmasked.
*
* @note not all of platform provide this function.
*/
void rt_hw_interrupt_umask(int vector);
/**
* This function will install specified interrupt handler.
*
* @param vector the interrupt number to be installed.
* @param new_handler the new interrupt handler.
* @param old_handler the old interrupt handler. This parameter can be RT_NULL.
*
* @note not all of platform provide this function.
*/
void rt_hw_interrupt_install(int vector, rt_isr_handler_t new_handler,
rt_isr_handler_t *old_handler);
/**
* This function will reset whole platform.
*/
void rt_hw_cpu_reset(void);
/**
* This function will halt whole platform.
*/
void rt_hw_cpu_shutdown(void);
/**@}*/

BIN
documentation/doxygen/images/Kernel_Object.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 9.9 KiB

BIN
documentation/doxygen/images/System_Arch.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 70 KiB

BIN
documentation/doxygen/images/Thread_Scheduler.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 8.5 KiB

BIN
documentation/doxygen/images/dfs.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 11 KiB

BIN
documentation/doxygen/images/finsh.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 7.1 KiB

BIN
documentation/doxygen/images/rtthread_logo.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 24 KiB

160
documentation/doxygen/kernel.h Normal file
View file

@ -0,0 +1,160 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup Kernel RT-Thread Kernel API
*
* The Kernel APIs are the core APIs of RT-Thread, which supports the following
* features:
* - Multi-thread management
* - Synchronization mechanisms
* - Inter-thread communication
* - Memory management
* - Asynchronous timer
*/
/**
* @addtogroup Kernel
* @{
*/
/**
* @defgroup Thread Thread Management
* @brief the thread management
*
* RT-Thread operating system supports multitask systems, which are based on thread
* scheduling.
* - The scheduling is a full preemptive priority-based scheduling algorithm.
* - 8/32/256 priority levels are supported, in which 0 is the highest and 7/31/255 the lowest.
* The 7/31/255th priority is used for idle thread.
* - Threads running at same priority level are supported. The shared time-slice
* round-robin scheduling is used for this case.
* - The time of scheduler to choose the next highest ready thread is determinant.
* - There are four status in thread management
* -# Initialization
* -# Running/Ready
* -# Blocked
* -# Closed
* - The number of threads in the system is unlimited, only related with RAM.
*/
/**
* @defgroup Clock Clock and Timer Management
* @brief clock and system timer management
*
* RT-Thread uses clock tick to implement shared time-slice scheduling.
*
* The timing sensitivity of thread is implemented by timers. The timer can be set as
* one-shot or periodic timeout.
*/
/**
* @defgroup KernelObject Kernel Object Management
* @brief kernel object management
*
* The Kernel object system can access and manage all of the kernel objects.
*
* Kernel objects include most of the facilities in the kernel:
* - thread
* - semaphore and mutex
* - event/fast event, mailbox, messagequeue
* - memory pool
* - timer
* @image html Kernel_Object.png "Figure 2: Kernel Object"
* @image rtf Kernel_Object.png "Figure 2: Kernel Object"
*
* Kernel objects can be static objects, whose memory is allocated in compiling.
* It can be dynamic objects as well, whose memory is allocated from system heaps
* in runtime.
*/
/**
* @defgroup IPC Inter-Thread Communication
* @brief inter-thread communication
*
* RT-Thread operating system supports the traditional semaphore and mutex.
* - Mutex objects use inherited priority to prevent priority reversion.
* - The semaphore release action is safe for interrupt service routine.
*
* Moreover, the blocked queue for thread to obtain semaphore or mutex can be sorted
* by priority or FIFO. There are two flags to indicate this mechanism.
* - RT_IPC_FLAG_FIFO
* when the resource is available, thread pended on this resource at first would get
* the resource.
* - RT_IPC_FLAG_PRIO
* when the resource is available, thread pended on this resource who had the most high
* priority would get the resource.
*
* RT-Thread operating systems supports event/fast event, mail box and message queue.
* - The event mechanism is used to awake a thread by setting one or more corresponding
* bit of a binary number when an event ocurs.
* - The fast event supports event thread queue. Once a one bit event occurs, the corresponding
* blocked thread can be found out timing accurately, then will be waked up.
* - In mailbox, the mail length is fixed to 4 byte, which is more effective than message queue.
* - The send action for communication facilities is also safe for interrupt service routine.
*/
/**
* @defgroup MM Memory Management
* @brief memory management for memory pool and heap memory
*
* RT-Thread operating system supports two types memory management:
* - Static memory pool management
* - Dynamic memory heap management.
*
* The time to allocate a memory block from the memory pool is determinant. When
* the memory pool is empty, the allocated thread can be blocked (or immediately return,
* or waiting for sometime to return, which are determined by a timeout parameter).
* When other thread releases memory blocks to this memory pool, the blocked thread is
* wake up.
*
* There are two methods in dynamic memory heap management, one is used for small memory,
* such as less than 1MB. Another is a SLAB like memory management, which is suitable
* for large memory system. All of them has no real-time character.
*/
/**
* @defgroup Device Device System
* @brief device I/O subsystem
*
* The Device System is designed as simple and minimum layer to help communication between
* applications and drivers.
*
* The Device System provide five interfaces to driver:
* - open, open a device
* - close, close a device
* - read, read some data from a device
* - write, write some data to a device
* - control, send some control command to a device
*/
/**
* @defgroup Hook Runtime Trace and Record
* @brief the hook function set in runtime
*
* In order to trace and record RT-Thread activity in runtime, a hook mechanism
* is introduced.
*
* The hooks are a series of routines, which are invoked in some special checkpoints.
* The hook routines include:
* - object hook, invoked at object created, deleted, taken and put etc.
* - scheduler hook, invoked at thread switch and idle thread loop.
* - memory hook, invoked when allocate or free memory block.
* - timer hook, invoked when timer is timeout.
*/
/**
* @defgroup KernelService Other useful kernel service
* @brief other useful service in the kernel
*/
/**
* @defgroup Error Error Code
* @brief error code
*
* The error code is defined to identify which kind of error occurs. When some
* bad things happen, the current thread's errno will be set. see @ref _rt_errno
*/
/**@}*/

49
documentation/doxygen/mainpage.h Normal file
View file

@ -0,0 +1,49 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @mainpage Introduction
* @author RT-Thread Development Team
* @version 1.2.0
*
* RT-Thread RTOS is an open source embedded real-time operating system and is
* designed specifically for small memory footprint platforms. The real-time and
* embedded characters are the most significant advantages of RT-Thread.
*
* - Real-Time Character
*
* RT-Thread has a real-time operating system kernel, with fully preempted
* multi-thread scheduler, inter-thread communication with timing sensitivity
* and transparent interrupt handling.
*
* - Embedded Character
*
* RT-Thread is suitable for embedded systems for small footprint characters.
* The kernel is implemented as a simple C library. The simplest application
* costs less than 1 Kbytes RAM on the ARM Cortex-M platform.
*
* @section kernel_arch RT-Thread Architecture
*
* RT-Thread system architecture is like:
* @image html System_Arch.png "Figure 1: RT-Thread Architecture"
*
* @section kernel_service Kernel API
*
* The Kernel APIs are the core APIs of RT-Thread, which supports the following
* features:
* - Multi-thread management and scheduler
* - Synchronization mechanisms, semaphore, recursive mutex and event set
* - Inter-thread communication, mailbox and message queue
* - Memory management, memory pool and dynamic heap memory management
* - Asynchronous timer
*
* For more details, please refer to @ref Kernel
*
* @section system_init System Initialization
*
* Once RT-Thread operating system starts up, the facility in system must be initialized
* firstly.
*
* For more details, please refer to @ref SystemInit
*/

14
documentation/doxygen/module.h Normal file
View file

@ -0,0 +1,14 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup Module Application Module
*
* @brief Application Module is a feature let user to execute application in RT-Thread RTOS.
*
* Application Module is implemented as dynamic object loader, but it can handle
* the dependences relationship between application and dynamic library, moreover,
* it also can handle the kernel object destroy and memory release issue when application
* (abnormally) exit.
*/

8
documentation/doxygen/readme.md Normal file
View file

@ -0,0 +1,8 @@
# How to build doxygen html
1. download from https://doxygen.nl/index.html
2. open `Doxywizard`
3. `File` -> `Open`
4. Open the file ./Doxyfile
5. To tab `Run` , Click `Run doxygen`

63
documentation/doxygen/systeminit.h Normal file
View file

@ -0,0 +1,63 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @defgroup SystemInit System Initialization
*
* @brief System initialization procedure.
*
* When RT-Thread operating system starts up, the basic operating system facility
* initialization routines must be invoked.
*
* The suggested initialization sequence is:
*
* - initialize device hardware
* rt_hw_board_init();
*
* User can put the low level hardware initialization in this function, such as
* DDR memory setting, pinmux setting, console device setting etc.
*
* - show version
* rt_show_version();
*
* - initialize timer system
* rt_system_timer_init();
*
* - initialize system heap memory
* rt_system_heap_init(__bss_end, __end_of_memory);
*
* - initialize module system
* rt_system_module_init();
*
* - initialize scheduler system
* rt_system_scheduler_init();
*
* - initialize application
* rt_application_init();
*
* - initialize system timer thread
* rt_system_timer_thread_init();
*
* - initialize idle thread
* rt_thread_idle_init();
*
* - start scheduler
* rt_system_scheduler_start();
*/
/**
* @ingroup SystemInit
*
* This function will initialize user application.
*
* This function will be invoked when system initialization and system scheduler
* has not started. User can allocate memory, create thread, semaphore etc. However,
* user shall not suspend 'current' thread.
*/
void rt_application_init();
/**
* @ingroup SystemInit
*/
void rt_system_heap_init(void* begin_addr, void* end_addr);

89
documentation/doxygen/thread.h Normal file
View file

@ -0,0 +1,89 @@
/*
* This file is only used for doxygen document generation.
*/
/**
* @addtogroup Thread
* @{
*/
/**
* @brief This function will handle IPI interrupt and do a scheduling in system.
*
* @param vector is the number of IPI interrupt for system scheduling.
*
* @param param is not used, and can be set to RT_NULL.
*
* @note this function should be invoke or register as ISR in BSP.
*
* @note this function is only implemented in scheduler_mp.c.
*/
void rt_scheduler_ipi_handler(int vector, void *param);
/**
* @brief This function will perform one scheduling. It will select one thread
* with the highest priority level in global ready queue or local ready queue,
* then switch to it.
*
* @note this function is implemented in both scheduler_up.c and scheduler_mp.c.
*/
void rt_schedule(void);
/**
* @brief This function checks whether a scheduling is needed after an IRQ context switching. If yes,
* it will select one thread with the highest priority level, and then switch
* to it.
*
* @param context is the context to be switched to.
*
* @note this function is only implemented in scheduler_mp.c.
*/
void rt_scheduler_do_irq_switch(void *context);
/**
* @brief This function will insert a thread to the system ready queue. The state of
* thread will be set as READY and the thread will be removed from suspend queue.
*
* @param thread is the thread to be inserted.
*
* @note Please do not invoke this function in user application.
*
* @note this function is implemented in both scheduler_up.c and scheduler_mp.c.
*/
void rt_schedule_insert_thread(struct rt_thread *thread);
/**
* @brief This function will remove a thread from system ready queue.
*
* @param thread is the thread to be removed.
*
* @note Please do not invoke this function in user application.
*
* @note this function is implemented in both scheduler_up.c and scheduler_mp.c.
*/
void rt_schedule_remove_thread(struct rt_thread *thread);
/**
* @brief This function will lock the thread scheduler.
*
* @note this function is implemented in both scheduler_up.c and scheduler_mp.c.
*/
void rt_enter_critical(void);
/**
* @brief This function will unlock the thread scheduler.
*
* @note this function is implemented in both scheduler_up.c and scheduler_mp.c.
*/
void rt_exit_critical(void);
/**
* @brief Get the scheduler lock level.
*
* @return the level of the scheduler lock. 0 means unlocked.
*
* @note this function is implemented in both scheduler_up.c and scheduler_mp.c.
*/
rt_uint16_t rt_critical_level(void);
/**@}*/

260
documentation/env/env.md vendored Normal file
View file

@ -0,0 +1,260 @@
# User Manual of Env
Env is a handy utility tool developed by RT-Thread team to build enviornment, graphical system configuration, and packages management for software projects that intend to run on RT-Thread operating system.
It is a wrapper tool for build-in menuconfig; an open source GUI tool which is designed to tailor for ease of use for developers. It can also be used to configure the kernel configuraiton parameters, components and software packages so that developers can construct the system like lego blocks.
## Main Features
- Menuconfig provides graphical interface to interact with operational logic and congfiguration parameters
- Each configuration option come with help session by default.
- It automates dependencies installation process.
- Automatically generate rtconfig.h without manual modification.
- It uses scons tool to streamline build project and compliation enviornment.
- Modular software packages and decoupling design make it easier to maintain.
- It also featured with point and click to download additional software packages and dependencies directly from Internet.
## Preparation
Env tool come with source code builder, compilation enviornment and package management system.
- [Download the Env tool](https://www.rt-thread.io/download.html?download=Env).
- Install Git (download link - https://git-scm.com/downloads). Follow git installation instructions and configure environment variable to add git.
- Take a note for working environment, all paths are not allowed to have Chinese characters or Spaces.
## User Guide of Env
### Open the control Console
The rt-thread software package environment is mainly based on the command line console so that the rt-thread development environment can be set up by minimizing the modification of configuration files.
There are two ways to open the console:
#### 1. click the Env directory executable file
To enter the Env directory, you can run `env.exe` in this directory. If it fails to open, you can try to use `env.bat`.
#### 2. open the Env console from the right-click menu in the folder
Add Env to the right-click menu:
![env settings](figures/Add_Env_To_Right-click_Menu-1.png)
![1561968527218](figures/Add_Env_To_Right-click_Menu-2.png)
![1561968626998](figures/Add_Env_To_Right-click_Menu-3.png)
Follow the steps from the image to launch the Env console from the right-click menu in any folder. Result are as follows:
![Right-click menu to launch the Env console](figures/console.png)
> Due to the need for the environment variables of the Env process to be set, the anti-virus software may misreport at the first startup. If the anti-virus software misreport is encountered, allow Env related programs to run, and then add related programs to the white list.
### Compile
Scons is a compile building tool used by RT-Thread to compile RT-Threads using the scons related commands.
#### Step One: Switch to the BSP root directory
If you use Method 1 to open Env console, you need to switch to the target BSP using the `cd` command.
For example, the target BSP is `rt-thread\bsp\stm32\stm32f103-dofly-lyc8`:
![stm32f429-apollo project directory](figures/cd_cmd.png)
#### Step Two: Compile the BSP
- Env carries `Python & scons` . To compile BSP, just use the default ARM_GCC toolchain by running `scons` command in the target BSP directory.
![compilation project using scons command](figures/use_scons.png)
Compiled successfully:
![complied successfully](figures/scons_done.png)
If you use mdk/iar for project development, you can use the project file in the BSP directly or use one of the following commands to regenerate the project and compile and download it.
```
scons --target=iar
scons --target=mdk4
scons --target=mdk5
```
For more scons tutorials, please refer to [*Scons*](../scons/scons.md).
### BSP configuration: menuconfig
Menuconfig is a graphical configuration tool that RT-Thread uses to configure and tailor the entire system.
#### Instruction for Shortcuts
Go to the BSP root directory and open the interface by entering `menuconfig`. The menuconfig common shortcuts are as shown:
![Commonly-used Shortcuts for menuconfig ](figures/hotkey.png)
#### Modify Settings
There are many types of configuration items in menuconfig, and the modification methods are different. The common types are:
- On/Off Type: Use the space bar to select or close
- Value, string type: After pressing the Enter key, a dialog box will appear, and the configuration items will be modified in the dialog box.
#### Save Settings
After selecting the configuration item, press `ESC` to exit, and select `Save` to automatically generate the `rtconfig.h` file. At this point, using the `scons` command again will recompile the project according to the new rtconfig.h file.
### Package Management
RT-Thread provides a package management platform where the officially available or developer-supplied packages are stored. The platform provides developers with a choice of reusable software packages that are an important part of RT-Thread.
[Click here](https://github.com/RT-Thread-packages) to view the official RT-Thread package, most of which have detailed documentation and usage examples.
As a part of Env, the `package` tool provides developers with management functions such as downloading, updating, and deleting packages.
Enter the `pkgs` command on the Env command line to see an introduction to the command:
```
> pkgs
usage: env.py package [-h] [--update] [--list] [--wizard] [--upgrade] [--force-upgrade]
[--printenv]
optional arguments:
-h, --help show this help message and exit
--update update packages, install or remove the packages as you set in
menuconfig
--list list target packages
--wizard create a package with wizard
--upgrade update local packages list from git repo
--force-upgrade update local package index file from git repo forcely (will auto-fix the conflicts when git merge).
--printenv print environmental variables to check
```
#### Download, update, and delete packages
Before downloading and updating the software package, you need to **open** the target package in `menuconfig`.
These packages locates in `RT-Thread online packages` , Once you enter the menu, you can see the following package categories:
![Package Categories](figures/menuconfig_packages_list.png)
Find the package you need and open, then save and exit menuconfig. The package will be marked, but has not been downloaded locally, so it is still unavailable.
- **download**: if the software package is selected but not downloaded, enter: `pkgs --update`, then the software package will be downloaded automatically;
- **update**: if the selected package has a latest update on the server and the version is selected **latest**, then enter `pkgs --update` , the package will be updated in local;
- **delete**: if a software package is not needed, deselect it in menuconfig and then use `pkgs --update` command. Then locally downloaded but unselected packages will be deleted.
#### Update local package information
As the package system grows, more and more packages will be added, so the list of packages in menuconfig may be **unsynchronized** with the server. This can be fixed by using `pkgs --upgrade` command, which not only synchronizes updates to local package information, but also upgrades to Env's functional scripts, which are recommended for regular use.
### Env Tool Configuration
- The new version of the Env tool includes an automatic update package and an option to automatically generate mdk/iar projects. The default is not enabled. It can be configured using `menuconfig -s/--setting` .
- Use `menuconfig -s` command to enter the Env configuration interface
![Env Configuration Interface](figures/menuconfig_s.png)
Press Enter to enter the configuration menu with 3 configuration options:
![configuration options](figures/menuconfig_s_auto_update.png)
The three options are:
- **Auto update pkgs config**：Automatic package update function: After exiting the menuconfig function, `pkgs --update` command is automatically used to download and install the package and delete the old package. This feature is used when downloading online packages.
- **Auto create a MDK/IAR project**: After modifying the menuconfig configuration, you must re-generate the project by typing `scons --target=xxx` . Turning on this feature will automatically regenerate the project when you exit menuconfig, without having to manually enter the scons command to regenerate the project.
- **Use China Mainland server**: Please **cancel it** if you are NOT living in mainland China.
- **Send usage data for improve product**: For user number statistic.
## Use Env in Your Project
### Requirements for Using Env
- Menuconfig is a feature of RT-Thread over version 3.0. It is recommended to update RT-Thread over version 3.0.
- Currently RT-Thread does not support `menuconfig` for all BSPs, which means that some BSPs can't be configured with menuconfig for the time being, but the commonly used BSPs are already supported.
### How to Modify Options in Menuconfig
If you want to add a macro definition in the configuration item of menuconfig, you can modify the `Kconfig` file under BSP. The modification method can search Kconfig syntax on the Internet for detailed documentation, or refer to the Kconfig file in RT-Thread or The Kconfig file in the BSP that supports menuconfig.
### To Add menuconfig function to New Project
New project here refers to a newly developed project that has not yet generated `.config` and `rtconfig.h`. Because these two files are only created when menuconfig is first saved. The specific process is as follows:
1. Copy the kconfig file from the BSP that already supports the menuconfig function to the new project root directory.
2. Note that modifying the RTT_ROOT value in Kconfig is the directory where RT-Thread is located, otherwise RTT_ROOT may be not found.
3. Start the configuration with the menuconfig command.
### To Add menuconfig function to Old Project
Old project here refers to the development that has been going on for a while, and there is a modified `rtconfig.h` file in the project, but there is no project configured with menuconfig. The specific process is as follows:
1. First back up the rtconfig.h file in the old project.
2. Use `scons --genconfig` command to generate a `.config` file from the existing `rtconfig.h` file. The `.config` file generated here saves the configuration parameters of the `rtconfig.h` file in the old project.
3. Copy the `kconfig` file from the BSP that already supports the menuconfig function to the root directory of the project you want to modify.
4. Note that modifying the RTT_ROOT value in Kconfig is the directory where RT-Thread is located, otherwise RTT_ROOT may be not found.
5. Use the menuconfig command to configure the old project we want to modify. Menuconfig will read the `.config` file generated in the second step and generate a new `.config` file and rtconfig.h file based on the configuration parameters of the old project.
6. Check the old and new rtconfig.h files. If there are any inconsistencies, you can use the menuconfig command to adjust the configuration items.
## Explore More with pip
In the Env environment, you can't directly use the pip tool provided by Python to install more modules. If you need to use the pip function in Env environment, you can reinstall the pip tool as follows:
1. Download the get-pip.py file from https://bootstrap.pypa.io/get-pip.py and save it on disk.
2. Run `python get-pip.py` command in the Env environment to reinstall the pip tool.
3. After the pip tool is reinstalled successfully, you can use `pip install module-name` command to install the required modules.
## Notes for Using Env
- For the first time, Env is recommended to go to the official website to download the latest version of the Env tool. The new version of Env will have better compatibility and also support automatic update commands.
- You can use the Env built-in command `pkgs --upgrade` to update the package list and Env's function code to minimize the problems you have fixed.
- Do not have Chinese or spaces in the routes of Env.
- Do not have Chinese or spaces in the routes where the BSP project is located.
## FAQs
### Q: There's unintelligible texts appear in Env.
**A:** First check if there is a Chinese route.
Check if the `chcp` command has been added to the system environment variable and try to change the character format to English using the `chcp 437` command. If the prompt does not have a `chcp` command, it is considered not to be added to the environment variable.
The directory where the `chcp` command is located may be added to the environment variable in the `system32` directory.
### Q: It prompts that the git command cannot be found.
'git' is not recognized as an internal or external command, possible program or batch file.
**A:** Git is not installed. You need to install git and add environment variables.
### Q: It prompts that the CMD command cannot be found.
**A:** Right-click–>> Property—>> Advanced System Settings—>> Environment Variable, Add `C:\Windows\System32` to system environment variables.
### Q: Prompt "no module named site" when running python.
**A:** Computer right button –>> Properties—>> Advanced System Settings—>> Environment Variable, in the user variable of the administrator, create a new variable named PYTHONHOME, and the variable value is: `F:\git_repositories\env\tools\Python27` （the installation route of Python in Env）, do not add ";" afterwards, otherwise it will be invalid. If add PYTHONHOME can not solve theproblem, try to add PYTHONPATH in the same way.
### Q: What types of projects can I generate under Env?
**A:**
1. Currently, you can use the scons tool to generate mdk/iar projects under Env. There is no automatic generation of eclipse projects.
2. Generally, using gcc's toolchain, using an editor such as source insight or VS Code to edit the code and compile with `scons` command.
### Q:How can my own BSP support menuconfig?
**A:** You can refer to this chapter **Use Env in Your Project**.
### Q: What is the difference between the pkgs --upgrade command and the pkgs --update command?
**A:**
1. The `pkgs --upgrade` command is used to upgrade the Env script itself and the list of packages. You cannot select a recently updated package without the latest package list.
2. The `pkgs --update` command is used to update the package itself. For example, if you selected json and mqtt packages in menuconfig, you did not download them when you exit menuconfig. You need to use the `pkgs --update` command, at which point Env will download the package you selected and add it to your project.
3. The new version of Env supports the `menuconfig -s/--setting` command. If you don't want to use the `pkgs --update` command after replacing the package, configure Env after using the `menuconfig -s/--setting` command. Select each time you use menuconfig. After the package is automatically updated.
### Q: Prompt "can't find file Kconfig" while using menuconfig.
**A:** The Kconfig file is missing from the current working BSP directory. Please refer *To Add menuconfig function to New Project* and *To Add menuconfig function to Old Project*.

BIN
documentation/env/figures/Add_Env_To_Right-click_Menu-1.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 24 KiB

BIN
documentation/env/figures/Add_Env_To_Right-click_Menu-2.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 52 KiB

BIN
documentation/env/figures/Add_Env_To_Right-click_Menu-3.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 76 KiB

BIN
documentation/env/figures/cd_cmd.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 25 KiB

BIN
documentation/env/figures/console.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 18 KiB

BIN
documentation/env/figures/hotkey.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 83 KiB

BIN
documentation/env/figures/menuconfig_packages_list.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 27 KiB

BIN
documentation/env/figures/menuconfig_s.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 22 KiB

BIN
documentation/env/figures/menuconfig_s_auto_prj.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 21 KiB

BIN
documentation/env/figures/menuconfig_s_auto_update.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 29 KiB

BIN
documentation/env/figures/q1.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 122 KiB

BIN
documentation/env/figures/scons_done.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 20 KiB

BIN
documentation/env/figures/use_scons.png vendored Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 27 KiB

BIN
documentation/figures/architecture.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 85 KiB

BIN
documentation/figures/architecturezh.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 73 KiB

BIN
documentation/figures/env.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 50 KiB

BIN
documentation/figures/logo.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 23 KiB

BIN
documentation/figures/qrcode.jpg Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 26 KiB

BIN
documentation/figures/studio.gif Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 3 MiB

BIN
documentation/figures/studiozh.gif Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 4.1 MiB

1027
documentation/filesystem/README.md Normal file
View file

File diff suppressed because it is too large Load diff

BIN
documentation/filesystem/figures/elm-fat-mkfs.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 22 KiB

BIN
documentation/filesystem/figures/fs-dir-mg.png Normal file
View file

Binary file not shown.
Side by side

After

Width:  |  Height:  |  Size: 11 KiB

Some files were not shown because too many files have changed in this diff Show more